shouldn't negatively affect anything, since I didn't remove a line
from the original patch which assigned to a variable. However, the new
patch added a line (after some comments) which assigned a value to the
same variable, so the end result was I left in extra code that did
nothing.
Pointed out by: bde
I noticed this one wasn't brought in, and was specifically mentioned in the
logs. I've tested this and the previous vix on my box and it appears to work
as well as before. :)
revision 1.42
date: 1996/11/13 18:31:57; author: bde; state: Exp; lines: +28 -17
Don't fiddle with RTS if RTS flow control is off. This gives applications
almost complete control over RTS (control of its initial value is still
missing).
This fixes PR 1644 for sio.
The author of PR 1644 wants it in 2.1.6 and 2.2. This may be safe since
the complications are only in rarely used cases that I hope I've covered.
Fixed handling of modem status changes. Only the most common case of
connect/hangup in !CLOCAL mode was handled correctly. mgetty and ppp
didn't work because they turn on CLOCAL and poll for carrier (or RI?).
Pointed out by: bde (on mailing list)
to fill in the nfs_diskless structure, at the cost of some kernel
bloat. The advantage is that this code works on a wider range of
network adapters than netboot. Several new kernel options are
documented in LINT.
Obtained from: parts of the code comes from NetBSD.
branch if one were going to try for orthogonality with the tag names
(RELENG_2_1_0 = 2.1.0-STABLE, RELENG_2_2 = 2.2-STABLE) but why perpetuate
the evil? :-)
Noticed-By: rgrimes
When compiling with '-Wall -pedantic', the byte swapping macros gave the
following warning:
warning: ANSI C forbids braced-groups within expressions
Adding __extension__ before the statement-expression seems to work right.
Submitted by: bde (a *long* time ago)
Requested by: jkh
Security patch from OpenBSD: fixes potential buffer overflow. (manually
applied because the diff was rejected).
Reviewed by: Warner Losh
Obtained from: OpenBSD
NOTE: I do not plan to move the RELENG_2_1_7_RELEASE tag after this
commit since the release has presumably already been rolled. If Jordan
wants to include this change, then he'll need to move the tag himself.
negotiation messages may be tagged, we were overrunning the old buffer.
The variable that was getting squashed is updated before the message goes
out, causing corrupted SDTR or WDTR messages. Depending on the phases
traversed before message out, this could cause the wrong offset to be
negotiated allowing data overruns to occur. The problem is easier to
detect with wide targets on the chain since the allowed offset is smaller.
Also removed the unnecessary clearing of SPIORDY during the message out
phase. We don't rely on SPIORDY any more.
to coredump previously since it (somewhat uniquely) is setuid and forks
without execing, and thus without passing P_SUGID the child could
coredump and possibly divulge sensitive information (such as encrypted
passwords from the passwd database).
Fully support auto termination and setting high byte termination.
Add support for memory mapped I/O.
Changed initialization order so that the ahc_in/outb functions can
be used for all I/O even at startup.
Reviewed by: wcarchive
Fully support auto termination and setting high byte termination.
Much better error handling and recovery code.
Add rudimentary Queue Full recovery code.
Style and type fixes.
Split up the interrupt handler into subfunctions to improve readability.
Reviewed by: wcarchive
SCB paging is now performed largely at the sequencer level.
Totally rewritten mesgin and mesgout phase handling
WDTR and SDTR message handling replaced with generic extended message
handling pushing the handling of extended messages up to
the kernel driver.
Support the NOOP message.
Don't clobber in-progress PCI transfers when shutting down DMAs.
Many other changes to improve error detection and correction.
Reviewed by: wcarchive
boxes since it was submitted.
The following small diff fixes the annoying fsck bug that causes it
to need to be run twice to end up with correct reference counts for
inodes for directories that had subdirectories relocated into the
lost+found directory.
Modstat is sgid kmem which is really handy to become if you feel like
looking through /dev/mem and /dev/kmem (gee, wonder what you might
want to do that for ). Like just about everything else under the sun
it has a buffer overflow problem. The problem exists in the dostat()
routine where an arbitrary sized string is shoved into sbuf.name
through a strcpy().
<http://www.l0pht.com/advisories.html>
This change was committed to 2.2 as rev. 1.4 of modstat.c by joerg, and is
being duplicated verbatim in 2.1-STABLE -JG
configuration changes having to do with DMA limits, change to the
way that the board is reset to avoid PCI/system hang, and don't
count short frames as input errors.
Tested extensively on wcarchive.
_startup_setlocale() per recent security hole bug report by
Thomas H. Ptacek <[email protected]>. The bug was also fixed
at a lower level in libc.
hole
of ugly hacks, and causes many side-effects in places it shouldn't.
The cvs people are aware of the problem but can't solve it, so I don't think
I should be touching it either.
versions, the DES-contaminated and the exportable one, during a `make
release'. This should fix the problems where /sbin/init and /bin/ed
have been missing in the `des' distribution of 2.1.6.
Requested by: jkh
Reviewed by: markm
David and I talked for quite awhile today about how to differentiate
2.1.6 from the "service patched" 2.1.6, and while the packaging
can and should stay the same, we still need to know version information
in bug reports. I'm therefore bumping the version to 2.1.6.1, though
I hope we won't need to refer to it often as such since the 2.1.6 CD will
be, in fact, 2.1.6.1 and I intend to also replace the FTP release with it.
2.1.6a and 2.1.7 were also debated and rejected. This version number
is the only one we've precedent for (1.1.5.1).
Bring in the more secure 8.8.3 sources onto the soon to be dead stable
branch in order to have them be part of the 2.1.6a 'security update'.
Reviewed by: Tom Samplonius <[email protected]>
block, even if newer GCC lets you get away with it. Case labels do
not begin a block, so I added a block around the code that requires
the new variable.
`ee' on the boot floppy already provides a screen editor anyway (not
the best, but hey - what do you expect for 1.2MB?).
Just getting this off my TODO list, in case this is ever picked up again.
I thought I *merged* this already! I even remember fixing the exact
same things I just fixed this time. Sigh. Maybe I just dreamed it.
Anyway, this would more than explain my floppy build problems. :-(
If anyone wants me, I'll be in the corner wearing the orange traffic cone.
Please be more careful when modifying code in this branch!
If my 8 hour release build had died (and it would have, in a few
more hours) because of this, I'd have been displeased. :)
Allow us to enable the 'XT_KEYBOARD' code using a configuration flag.
This allows the user to add modify syscons's configuration flags using
UserConfig that will allow older/quirky hardware (most notably older IBM
ThinkPad laptops) to work with the standard boot kernel.
(note: I used the same flag as in -current so the documentation would be
the same)
Inspired by: The Nomads
that -current is based on. This has been tested on wcarchive for about
12 hours and in -current for a couple of months.
This update should fix many of the compatibility problems that people
have reported.
fix, but low-impact and worth the comeasurate risk. I [jkh] can't even
test it in -current since systat's vmstat display is completely broken
there at the moment, printing out: "The alternate system clock has died!"
Submitted-By: Heiko Blume <[email protected]>
3COM 3C590 Etherlink III PCI,
3COM 3C595 Fast Etherlink PCI,
3COM 3C592 Etherlink III EISA,
3COM 3C590 Fast Etherlink EISA,
3COM 3C900 Etherlink XL PCI and
3COM 3C905 Fast Etherlink XL PCI.
This driver is based on OpenBSD's driver. I modified it to run under FreeBSd
and made it actually work usefully.
Afterwards, [email protected] (HAMADA Naoki) added EISA support as well as
early support for 3C900 Etherlink XL PCI and 3C905 Fast Etherlink XL PCI.
He also split up the driver in a bus independant and bus dependant parts.
Especially the 3c59X support should be pretty stable now.
Submitted by: partly [email protected] (HAMADA Naoki)
Obtained from:partly OpenBSD
if it comes down to it, but not that many. BTW, in case it's not
obvious, I'm mostly merging away in -stable while phk and joerg do the
2.2-current merging for now. I'm getting 2.1.6 out of the way so that
I can concentrate on 2.2.
doing so breaks the looping and bad things will happen. This was exposed
when testing some (aha2940) fixes from Justin that didn't work because of
this.
This fix is relevant only to -stable since -current already has the
equivilent in the contigmalloc() routine.
this eliminates cosmetic differences and brings over the staticizing
of this file.
Add detection of several Intel chips recently added to HEAD (Natoma and
Orion GX/KX).
More clean up work will happen after pass 2 of merging once the files
are pretty much identical. After that additional bootverbose chipset
register dumps will be added (Triton-II and Natoma).
lib/libdisk, and secure/lib/libdes. Now a make -DCLOBBER includes _fully_
recreates /usr/include, which then allows the x2ph stuff to get all of the
files when DESTDIR is set.
Alphabetize the gnu/lib/lib* section of includes:
This ought to make it more tolerant against another chip set that does
not conform to the PCI spec with regard to the configuration address
register ...
as soon as Peter sees this. :-) Peter: Another problem: There were
two files modified in -current; installUpgrade.c and label.c. Of the two,
only label.c is branched properly (re: our earlier conversation with apache.c).
I don't know what effect this has, if any, but just FYI..
already been tagged onto the -stable branch):
aic.4, eg.4, el.4, ep.4, mtio.4, ncr.4 and wt.4
Also include some additional MLINKS for the spkr and pcvt man pages.
GENERIC - Add a commented out line for adding support for IBM ThinkPad
keyboards
LINT - Add SCANSET=2 support to the LINT kernel and comments reflecting it's
purpose.
decode the partition bits, so having both wcd0a and wcd0c is dangerous
and almost useless) and sound and mouse anachronisms. All cosmetic
except for fixing some transiently wrong permissions and one missing
chgrp (there are still many minor bugs in this area).
of the Intel Architecture Lab, disabled the optimized Pentium microtime.
It causes two bugs in 2.1.x: it doesn't account for laptops with power
management and it sometimes is broken completely because the cycle_counter
comes up with the wrong value. I've seen this latter bug occur dozens of
times. The implementation in the main branch addresses some of these
issues, but we're too close to the release to consider bringing in all
of those changes, so this is the safest solution.
Reviewed by: bde
except that upages are handled differently in -stable. This version
fixes a potentially serious hole dealing with incorrect object locking.
Reviewed by: dyson
``no advertisment'' clause).
NB that i've also included the find_interface examples into 2.1.X, but
this happened by a CVS tag operation behind the scene, thus no commit
message. The parent Makefile is supposed to pick this change
automagically.
It's important that pmap_enter() be used here because the pages won't
be removed from the kernel VM when freed otherwise. This would result
in the potential for the wrong page(s) being used if a vm_map_pageable()
was done on this same address space (since no fault would occur, the
previous page(s) would be bogusly used instead). This is almost
certainly yet another cause of wcarchive instabilities.
Thanks to John Dyson for helping me track this one down!
mapped into any processes.
Also set b_pages[]=0 when the pages are removed from the buffer - this
is to satisfy my paranoia by making sure that nothing bogusly messes with
the pages after the buffer has been reclaimed. A similar change was made
in the main branch some time ago.
condition. Also, it's possible that we might not be dealing with the same
page if the vget() should block but still succeed (this is possible), so
be sure to check to see that the page is still dirty and on the PG_INACTIVE
queue. Checks in vm_pageout_clean() will guarantee that the page is still
a condidate for pageout (busy, hold, PG_BUSY, etc).
to the major differences in the VM systems in current and stable, this
retrofit does have some significant algorithmic differences. In any
case, it should be superior to the old (recursive) algorithm in every way.
This, along with the vm_glue.c fix, should fix all of the recent
paging performance complaints.
Reviewed by: dyson
This fixes a serious profiling bug: All addresses >= 256K caused
an overflow, and had their times tallied in the wrong counters.
Bruce Evans has devised a more complete fix that addresses other
issues as well. But for now, this simple fix is effective and
easy to understand, making it worthy of inclusion in 2.1.5.
few edits to this still don't solve the original problem. It appears
that the recursion is *much* worse than we thought - I'm already testing
at 30 levels deep, and it still terminates before finishing the job.
This problaby explains some people's stack overflow problems... :-(
broken and return wrong data to the user. Sigh...I need a vacation.
This patch is copied directly from John's edit on the main branch,
so I'm *sure* it is correct. :-)
MAXPHYS/PAGE_SIZE pages. This occurs when there is a non-page aligned
I/O of MAXPHYS size. The fix is to trim the request to MAXPHYS-PAGE_SIZE.
It apparantly wasn't noticed previously because of other bugs.
- Install Makefile.yp as /var/yp/Makefile.dist and only make a link
to it from /var/yp/Makefile if /var/yp/Makefile doesn't already
exist. This way we won't clobber an existing copy of /var/yp/Makefile
which the user may have modified and wants to keep.
- Make the services.byname target generate proper map keys.
This will probably be my last commit to this branch unless the
freeze deadline changes for some reason.
removed special sparc support; added ${LDFLAGS} to linker rules.
Enabling the .c rule fixes PR 1347. The bugs in null suffix rules that
stopped this being enabled in 2.0.5R were fixed long before 2.1R.
In _yp_dobind(), don't spew an error message on failure to contact
ypbind unless it's for something really out of the ordinary. This stops
_yp_check() from generating a lot of pointless noise. (Example: set your
system domainname but don't turn on NIS, then do an rpcinfo -p. Watch
as 'clnttcp_create' errors scroll by.)
pw_yp.c:
- Fix silly bug in copy_yp_pass().
- In yp_submit(), use the password from the pw struct passed in as
an argument instead of calling getpwnam() to find it: for one thing
this is unnecessary since we already have the crypted password, and
for another it cause us to pick the wrong password in the event that
the user exists both in the local database and in YP.
edit.c:
- Change shell restriction policy: if the shell field isn't restricted
and it's valid, or if the the user is root, allow the shell field to
be edited.
- Show the "B" flag on blackhole routes (as documented)
- fixes from 4.4Lite-2 to make the dns reverse-lookups a little less
broken in the face of subnets (and show network route size)
- more sensible trimming of the local host's domain name.
- more readable '-w' statistics output
(The actual import of wormcontrol(8) into the branch is done behind
the scene by a cvs tag operation, you'll only see a commit message for
the Makefile change.)
The existing worm driver there was entirely useless, you couldn't do
anything with it. Thus i believe that shipping a beta-quality driver
is still better. (The only other option would have been to remove it
from the branch.)
Not only is the code higher quality, but it also fixes a rounding/off-by-
one bug that caused a panic when doing physio() with DIAGNOSTIC. This
fix closes PR#1195.
need to be merged as well for this to work, but they're in a different part of
the subtree. I have to merge this because a) our -stable docs are way out of
date and b) I need the "doc" distribution to appear in -stable if I'm to use
a single copy of sysinstall for both. Reviewers of this MOST welcome!
queues and inadvertantly stepping off the queue via a page that was
previous removed from it. Also killed the potentially evil RSS limiting
code in the vmdaemon - it traverses allproc which would not be consistent
if the code should block for some reason (it shouldn't block, but we're
not completely sure of that...).
Submitted by: dyson
version isn't ready and the version in -stable is quite broken):
- read optimization
- corrections in data flow mechanism
- restoring board memory window state while returning from
reentrable functions
1996/03/16:
- now several boards can coexist and share the same memory window
1996/03/24:
- eliminated 'b_to_q to a clist..' message while turning off modem
1996/04/10
- 'static int nports'... - next attempt to drive several boards.
Reported that with this fix it works with 2 boards.
1996/04/20
- Overloading channel (ping -f host) caused 'No buffer space..'
state until slip unit restart. Fixed.
Submitted by: "Serge A. Babkin" <[email protected]>
Changes by: Oleg Panashchenko <[email protected]>
can/will allocate map entries at interrupt time. This is similar to a
(splvm) change that was made in the main branch, but much simpler. The
code in the main branch is broken (the thresholds are of such that
freed map entries will accumulate on the non-kernel pool)...so the fix
was re-implemented with just the spl protection and minor algorithmic
simplification.
This is similar to the splvm() protection that was added in the main
branch. It protects the queues from page insertions that can happen during
buffer rundown of asynchronous I/O read-aheads.
call to pmap_enter(). Closes a window where PG_MAPPED might be cleared
if the process blocked and someone else does a vm_page_protect(NONE)
before the process unblocks.
Reviewed by: dyson
that has to do with the PG_MAPPED flag not being set at the right time,
and PG_BUSY the page rather than doing a vm_page_hold/unhold. This
fixes a potential problem where some mapped pages might go unnoticed by
other parts of the vm system, which can be a real problem if the page(s)
are reclaimed.
Reviewed by: dyson
instead of buggy explicit code to fix the `Avail' count returned
by statfs() for file systems larger than 11GB. This also fixes
a minor rounding bug. The count is still wrong for file systems
larger than 1TB/minfree (normally 128GB).
mode when this occurs and allow the target to complete the transaction.
Force a retry on overruns since they are usually caused by termination or
cable problems.
deserve a life there, and chances that it compromises some other part
of the system are low.
Reviewed by: [email protected] (Greg Lehey)
(Should have made it into a single commit, but i've botched this.)
Note, I'm only bringing in the bare minimum necessary to support doing
reverse PTR using CNAME's, which is necessary for the
'Classless in-addr.arpa delegation' draft, which is now in use by many
ISPs. This file is now the at the 'bind-4.9.3-REL' revision level.
Inspired by: John Capo
Fixed bogus changes from mega-commit 3. This reverts the files to their
revisions *before* the mega-commit but makes sure any subsequent fixes
are brought in.
by mistake). CVS is acting _very_ strangely here; claims everything in
/sys/sys for 2.1 is in conflict, even if I remove it every time. I'm starting
to REALLY HATE CVS and will do no more merge work with it once the tree is
working again. I've had it with trying to merge things with CVS - that's it,
I quit! I've merged my last change into 2.1.
Bring in changes from if_ep.c for PCCARD driver.
Properly determine the offset of the remaining bytes we need to
transfer after outsl'ing all the long words we can during transmission
in 32bit mode.
Used the above as part of a fix for an architectural flaw in the way that
sysctl_doproc works. sysctl_doproc can block while traversing the proc
lists and the state of the list may have changed during this time. The
fix is to check that the process still exists, and if not, restart the
loop from the beginning.
Note that I don't understand how to unwind SYSCTL_OUT things in -current,
SO SOMEBODY ELSE WILL HAVE TO IMPLEMENT THIS FIX THERE!!! (Poul?)
set-id ktrace bug, some cosmetic changes (brought in to make the merge of
other fixes possible), and use kmem_alloc_wait/kmem_free_wakeup to
eliminate a transient string space allocation failure due to running out
of map space.
Watch out for falling rock until phase 3 is over!
libc completely merged except for phkmalloc & rfork (don't know if David
wants that).
Some include files in sys/ had to be updated in order to bring in libc.
The problem with doing this is that getpwnam() will process all the special
inclusion and exclusion lines in /etc/master.passwd, including substitution.
So, for example, if you have a line on your NIS master server that says:
+@disallowed-users:::::::::/etc/nologin
Then yppasswdd will end up with a user record that has /etc/nologin as
a shell. This in turn will get propagated into /var/yp/master.passwd
when an update is performed, and the user's shell will be changed to
/etc/nologin, thus locking them out of the system.
To fix this, yppasswdd now retrieves the user's master.passwd record
directly from ypserv using a call to yp_match(). This bypasses all
the inclusion/exclusion/substitution processing in getpwent(3).
Note that rpc.yppasswdd in FreeBSD-current does not suffer from this
problem: it digs directly into the map database files when searching
for user records, which means it not only bypasses getpwent(3), it
will also work even if your NIS master server isn't set up as an NIS
client. I could have done something similar here, but that would have
meant adding DB interface code which would have been much more complicated.
Bug pointed out by: Tom Samplonius
constants that can be overridden at kernel config time that are not
visible while running that kernel.
Also, dont dig into /proc/<pid>/mem to read process space if working
on a crashdump.
libkvm to adapt to the kernel VM layout changing. (such as on wcarchive,
and some of the stuff I'm experimenting with at the moment. -current
already has this, so that 2.1 programs that have setproctitle statically
linked will work on 2.2 even if 2.2 ends up with PS_STRINGS in a different
location)
Also, added the somaxconn etc entries, because of the way that the
user-mode sysctl program is built and it was either add the real things, or
some placeholder stubs.
Fix a race condition in p_mesgout* and inb* code that could allow a
phasemiss to sneak by without detection. This should fix the
Wide/Narrow boot problems that have been reported since this bug
caused the driver ignore a narrow target rejecting wide negotiation.
Properly determine the offset of the remaining bytes we need to transfer
after outsl'ing all the long words we can during transmission in 32bit mode.
Closes PR:i386/1243
Submitted by: [email protected]
Setup ULTRAEN in SXFRCTL0 to match the syncrate we are using during the
call of ahc_scsirate. Otherwise, the proper setting may not get set until
the next reconnection/selection.
The saved_queue used to re-order the QINFIFO during error recovery or
certain SCB paging operations should be an array of u_chars not ints.
saved_queue type error pointed out by: Noriyuki Soda <[email protected]>
Dynamically Enable/Disable Ultra mode on a per target basis. Remove
broken Ultra sync rate entries. Remove an unneeded printf. Turn a
panic into a printf since the sequencer will recover if a bad phase
is detected.
This covers the security problem descibed in SA-96:10 and Jeff says that
when we upgrade to Lite2 (which fixes this problem), mount no longer needs
to be setuid, so we'll never be going back.
Submitted by: hsu
Reviewed by: pst
Leave 16 lines in front of each component partition. It's now safe to
use sd87a or sd237e even if they start at the beginning of the slice.
You can also use sd85c if you prefer, although you need to change the
type field in the disklabel to "4.2BSD".
Fix a brain-o. The scratch ram on aic78X0 controllers is initialized to 0x00
not 0xff after POST, so test for that when trying to determine if a BIOS
intialized the card for us.
Add io_port to SCSICONF when
Add missing '+ io_port' to two outbs.
Add missing splx() in one error case during probes.
Remove unnecessary return and break.
Submitted by: Noriyuki Soda <[email protected]>
2. Nuke libdisk from here in preparation for a move to /usr/src/lib, as in
-current.
3. Remove explicit references to libdisk in Makefile (which will probably
be merged outright from the HEAD later, but this will do for now).
used in /etc/hosts.equiv and /etc/netgroup doesn't exist), fixes another
bogon that I discovered independently (_yp_innetgr flag not reset at
the right time) and small performance tweak.
1) allocate map VM from the kernel_map, not the kmem_map.
2) update map hint properly when simplifying a map and remove unnecessary
restriction on object->paging_in_progress.
The above problems wouldn't have caused any panics, and it's unlikely
that there were any noticeable effects due to the bugs...but they're bugs
nonetheless.
Submitted by: dyson
of the optimizations. Most of this is a rewrite to get rid of the inline
assembly. I've been seeing some very strange page table related panics
on wcarchive with the old code; the current thinking on this is that the
inline assembly in pmap_remove isn't getting along with the gcc code
generator for some reason (possibly due to a bad or missing register
constraint) and in any case the problems seem to disappear with the C
(new) version of this code.
Reviewed by: dyson
- This code adds some backwards compatability hacks for buggy APM BIOS
implementations, and synchronizes us with the Nomad's latest code.
This code is based on the Nomad code, but heavily hacked by me.
Reviewed by: phk
Submitted by: the 'Nomads'
Add the APM hooks into the generic pccard kernel files. With this code
in place device drivers can now register power-down/power-up routines so
that we can use common routines to power-up/power-down cards for
insert/removals, suspend/resume, etc..
Reviewed by: phk
Submitted by: the 'Nomads'
regarding apm to LINT
- Disabled the statistics clock on machines which have an APM BIOS and
have the options "APM_BROKEN_STATCLOCK" enabled (which is default
in GENERIC now)
- move around some of the code in clock.c dealing with the rtc to make
it more obvios the effects of disabling the statistics clock
Reviewed by: bde
- Addition of my name to the APM Copyright
- More code cleanups
- #ifdef DEBUG debugging code
- More consistant printfs
- Better handling of the apm_int() assembly code (mostly from Bruce Evans)
- Save/restore the FS data segment.
Reviewed by: bde
When cslip gets an uncompressed packet, it attempts to save off the TCP/IP
header for use in decompressing subsequant packets. If cslip gets garbage
(such as what happens when there is a port speed mismatch or modem line
noise), it will occasionally mistake the packet as a valid uncompressed
packet. When it tries to save off the header, it doesn't bother to check
for the validity of the header length and will happily clobber not only
the cslip data structure, but parts of other kernel memory that happens
to follow it...causing, ahem, undesired behavior.
- Changed #includes of <i386/include/foo.h> to #includes of <machine/foo.h>.
- pccard.c:
#include <i386/include/clock.h> to get sysbeep() prototype
- pcic.c:
add appropriate #ifdef around a prototype to quiet GCC because
fn decl. is also #ifdef'd.
Don't immediately give up if a single read() or write() wasn't
sufficient to transfer all the data from stdin, or to stdout. Working
on pipes causes further fragmentation.
Purge the SCSI system from its internal types int32, int16, int8, u_int32,
u_int16, u_int8.
aic7870.c
Remove "scb walking" code. Its replaced by the dynamic SCB discovery
code in aic7xxx.c. Fix setup of SCSICONF.
bt9xx.c
spaces -> tabs
ncr.c
Use XS_SELTIMEOUT error code for selection timeouts.
Purge the SCSI system from its internal types int32, int16, int8, u_int32,
u_int16, u_int8.
aic7xxx.c aic7xxx.h
Change method for dealing with parity errors. Support the aic7850.
Fix the timeout code. Remove bogus declaration of RESTART_SEQUENCER
and UPDATE_SEQUENCER from aic7xxx.h. Dynamically determine the number
of SCBs. This driver is identical to the one in -current except I've
left parity error handling disabled until it is verified in -current.
bt.c
Use varargs/stdarg in bt_cmd. Use the XS_SELTIMEOUT error code for
selection timeouts.
Purge the SCSI system from its internal types int32, int16, int8, u_int32,
u_int16, u_int8.
aha1542.c
Use stdarg/varargs in aha_cmd. Use the XS_SELTIMEOUT error code for
selection timeouts. Staticize.
bt5xx-455.c
Overide the unit number passed in in our isa_device structure with the
current unit in bt_unit. This kludge makes the unit numbers sane when
there are PCI/EISA/ISA probes going on.
isa.c
Regester the ISA bus as "ISA bus" instead of "ISA or EISA bus".
if_ep.c
Many bug fixes from -current. Split out the eisa probe into an
eisaconf probe so it doesn't conflict with the aic7xxx driver.
Bring all changes to the eisaconf code from -current back to -stable.
aha1742.c
Don't pass unit numbers around. Use softcs instead.
3c5x9.c
Eisaconf probe for the 3c579 and 3c509(in eisa configuration mode).
Another round of fixes:
. Replace my NIH-suffering code to detect the number of lines on
the terminal by the curses variable LINES.
. Fix the selection code for countries with more than one screenful
of locations. The very few people living in America/US/Pacific
now won't be charged for Indiana any longer... :)
. Removed the gross code that copied over the timezone file to
/etc/localtime, and create a symlink now instead.
I've also added tzsetup.8 while i was at it.
Change v_usecount & v_writecount from a short to an int. As shorts they
can and will overflow on large machines - especially on machines with
filesystems with lots of files (like netnews servers), and the result
is a "free vnode isn't" panic or worse.
This fixes one of the causes of these panics that I've been experiancing on
wcarchive.
freebsd.mc/cf is a generic configuration, while freefall.mc/cf is the
industrial-strength configuration that we actually use on freefall.
The freebsd mailing list mail-relays may find freefall.mc template a much
better starting point.
holes and a lot of bugs.
8.7.* has pretty much finished development, 8.8 is in alpha testing.
A seperate commit will follow to do a couple of 2.1.x specific things and
to turn off the infamous 8bitmime->quoted-printable conversion when talking
to older sendmails.
OK'ed by: davidg
(Note: a lot of tags were added behind the scenes for the new files)
Bloat the -stable etc tree with unused PC-CARD support hooks to make
testing go easier. This code won't do anything in -stable, but it
minimizes the # of patches the testers will have to make to their
systems.
- Fix the APM 'idle/busy' functions.
- Call apm_int() instead of doing direct assembly calls.
- Added kernel compile time failure if more than one APM device is configured.
- Always enable interrupts before calling the APM idle/busy routines.
- Minor bugfixes from the recent PC-CARD release.
Move the YP initialization earlier, so it's done before the evaluation
of -p/-s/-a related cruft.
Closes PR # misc/933 "chpass -s <shell>" does not work
(enable/disabled) now that the APM_GETINFO ioctl returns the necessary
information. Also, print out the status along with the other
information as the default behavior.
just in case a connection already existed.
Also, a minor optimization in the code which determins if a APM BIOS exists.
Reviewed by: phk
This is based on the APM-0.5 patch for Linux, but written entirely by me.
revision 1.4
date: 1996/01/30 22:53:13; author: mpp; state: Exp; lines: +2 -2
Fix a bunch of spelling errors in the comment fields of
a bunch of system include files.
a sigreturn, There's up to 20 of these per second, and syslogd is
fsync()'ing the /var/log/messages file.. :-(
This is "expected behavior" for the level of code in -stable.
doesn't break support for the older models (tested with my 3C589B).
Reviewed by: Joshua Gahm <[email protected]>
Submitted by: [email protected] (HOSOKAWA Tatsumi)
build/install xinstall before doing a 'beforeinstall' in includes.
allow "make -DNOCLEAN" to avoid the clean/cleandir/cleandist altogether
"tools" -> "build-tools" label to avoid the risk of "make tools" actually
seeing a stray "tools" directory when working with both -current and -stable
Obtained from: -current
Close the ip-fragment hole.
Waste less memory.
Rewrite to contemporary more readable style.
Kill separate IPACCT facility, use "accept" rules in IPFIREWALL.
Filter incoming >and< outgoing packets.
Replace "policy" by sticky "deny all" rule.
Rules have numbers used for ordering and deletion.
Remove "rerorder" code entirely.
Count packet & bytecount matches for rules.
This has remote repository access via "rsh".
(eg: $CVSROOT = freefall.freebsd.org:/home/ncvs)
This is not quite the latest version, but it's a "known quantity".
There were a few covert tagging operations done as well to bring some
new files onto the -stable branch, these do not show here.
flags. This is so that all the "cmp -s foo /usr/xyz/foo || install -c .."
gunk doesn't need to be re-added to a couple of things heading this way
from -current.
the other way around - the changes in -current were based on these).
The NO_SWAPPING option disables U-area paging (struct user & kernel stack)
and can help improve performance in some special circumstances where a
system has plenty of main memory and also has a lot of processes that are
often in short waits (< 1 minute) but wake up frequently. Such is the
case on a busy FTP archive like wcarchive. This option does not affect
generic VM system paging.
accounts for the weird behavioral differences that Satoshi and I saw
when testing out the new link testing changes to bsd.port.mk - he was
running -current and I -stable.
The ipfw code will no longer sort the rules as default.
This means that access-lists may take a different meaning now.
>>> Please review your access lists <<<
If the salt starts with $1$, preserve it rather than overwriting it.
This allows a dual-personality crypt to sense which algorithm to use.
Some other cosmetic nits from HEAD too (null terminate a salt string in
#ifdef'ed out code).
This is a "trivial" change - if it is presented with a "$1$ salt (which
is illegal for the DES crypt), it switches to the md5 routine instead.
If it never sees a MD5 string, it behaves exactly as before.
This will be a lifesaver for people who install from cdrom, add users or
set passwords, then go and select the "secure" dist from the ftp server
and would have locked themselves out of their machine.
Some -Wall cleanups came along with it.
Added/updated some standards for the .St macro.
Updated the .Os macro to stop reporting "BSD Experimental", and
taught it about FreeBSD and our various versions.
part of rev.1.115:
Fix the tests for being a console by reverting to the ones that
were used before the the RB_SERIAL changes...
all of rev.1.123:
Removed builtin list of port addresses. The address for sio3
conflicted with S3 graphics cards...
Take a different approach to the SPIORDY race condition. Simply clear
SPIORDY just before we ack on the bus so that there is no chance to
see SPIORDY for the same byte twice.
Make some small modifications so that the Linux aic7xxx driver can use
our sequencer and register definition files verbatum.
-Added support for the slip.hosts options 'normal', 'compress', 'noicmp',
and 'autocmp'.
-Additionly parse /etc/sliphome/slip.slparms* to set keepalive,
outfill and slunit.
-Make it more POSIXed.
-Describe undocumented stuff.
int shmget(key_t key, int size, int shmflg);
If the 'key' has already existed in the system and set 'shmflg'
as '(IPC_CREAT|IPC_EXC)', then shmget() must return the error 'EEXIST'.
Submitted by: [email protected] (Mihoko Tanaka)
Add a name to the context structures for compatability
with the CVS in -current. Basically,
typedef struct { ... } MDx_CTX; becomes
typedef struct MDxContext { ... } MDx_CTX;
Disallow setgroups() with ngroups=0. There should always be one group (the
effective gid). This works around a panic ("nfsreq nogrps") that occurs
with NFS clients. This change is too late for 2.1-release.
Obtained from: 4.4BSD-Lite2
2.1-release. The effects of the missing splx would be seen on NFS clients
with soft or intr mounted filesystems and then only after a timeout had
occurred.
Submitted by: dyson
Bleah. Now the chained dependency adds work from FTP sites. This was
really totally broken before, despite my claims to the contrary. Sorry
folks. I guess nobody uses the pkg_add ftp://... feature or somebody
would have reported it by now! :-)
cd ${.CURDIR}/eBones/lib/libkadm && ${MAKE} beforeinstall
To includes target. Move the other one inside the eBones .ifdef too; must
have been really sleepy before!
[Mark, you really don't need a diff for this - it's pretty obvious! :-)]
o Caution against use of `W' options in label/partition screens (dangerous!)
o Make various types of debugging dreck conditionalize on DEBUG flag
o Make a fake /var/db/mountdbtab file so new system doesn't complain
o Apply uniform permissions to entire /usr/X11R6 tree.
o Set erase character to ^H for all interactive commands.
o Don't panic if user exits upgrade shell, reboot.
o Document dangers of `W' options in help screens also.
2. Fix a stupid bug that resulted in strange (but usable) looking entries in
/etc/hosts.
3. Make sure /usr/X11R6/bin is executable by all (I really need an mtree
script to run for the entire /usr/X11R6 hierarchy since cpio is scrambling
the perms for some reason and I suspect that this is only a partial fix!)
that the adduser command is just too broken to allow it to be used
in automated creation mode (it loops forever) and this option is therefore
retired until we get it fixed.
1. Fix the bogon I introduced that made some root filesystems fail to be
made with `unable to make filesystem on sd1s1a' or some such error
message.
2. Latest installment in the never-ending chapter on making FTP do the right
thing on a cruel internet.
3. Make `express install' a truly express install and split off what it used
to do into a `novice install' that's even more geared to the novice
by asking questions in order, rather than forcing them through the menu
interface.
4. Make anonymous FTP setup truly DTRT.
5. Build lndir directly into sysinstall and make the novice install offer
to set up the ports tree. Also make the ports setup truly explanatory
about what it's doing, and always link the ports destination to /usr/ports
if necessary so that bsd.port.mk doesn't need to be tweaked.
1 ) Tar was being called to process the archive after chdir()ing into the
playpen, but the pathname given to it was uncorrected for the chdir().
This is corrected by converting _all_ pathname arguments using
realpath() (fileFindByPath() is used as a last-ditch attempt if the
argument can't be found)
2 ) min_free was being called on the saved invocation directory, not on
the playpen at one point. (There are currently two seperate space
checks, one when the playpen is created, and one later. This is
harmless cruft)
Submitted by: Michael Smith <[email protected]>
belong. They should be actually moved in the source tree to be under
eBones, but I don't want to mess with that now. This should hopefully
fix the main problem people were having when they selected the "des"
distribution and not krb, but got the Kerberos version of telnet and
friends as a side effect.
Submitted by: Justin Gibbs <gibbs>
o Lots of documentation fixes.
o Rename FTP active to "FTP" and explain passive mode better.
o Make tcpip screen a bit more friendly.
o Literally dozens of nits.
2. Fix an infinite recursion bug in FTP retry. Tricky, this FTP install!
3. Add messaging routines for scripts.
4. Fix yet more bogons. I think I'm fixing them faster than they're growing,
but it's hard to say. I'm really glad we're throwing this code away for
2.2!
don't bogusly restore the screen to the message that was the cause of the
abort. That resulted in lots of weird flickering dialog boxes that appeared
to be displayed out of sequence.
blithly assume that HOME *is* set, but it's probably easier to just set
it to some reasonable default here rather than assuming that no other
apps will get similarly confused.
that the FTP install doesn't deal with timeouts and hasn't since it was
written. Fixed.
2. Totally eliminate the OptionFlags. I only had to work harder to
sync them with configuration variables, so why not simply always use
configuration variables? This has actually greatly simplified areas
of the code.
o Implement the 2.0.5->2.1 upgrade procedure (gah).
o Bring in Coranth's support for configuration of anon ftp and Samba
plus some changes of my own.
o More attempts to actually write the documentation in english.
o Update docs to contain more 2.1-centric information.
I'm really, truly using it). Allow distribution fetch to get .info
files from the root.flp OR the distribution in question, allowing us
to add flexibility to the scheme. At some point, perhaps soon, the
cached copy should probably go away entirely!
Merge today's work.
Now support an attributes file loaded at startup (true front-loaded install).
Add fuller debugging support to all device I/O routines.
Lots-o-bug fixes.
Remove the ATAPI kernel hack.
Remove the now-unnecessary work-around for booting root off a slice; it
appears to work just fine now and will confuse a lot fewer folks.
methods. This should make the process rather more robust in the face
of entropy.
o Let tape cpio extract guess type of tape format.
o Hide cursor better in options screen.
gzip'ed kernel image over itself.
I've tested this on a 4 MB machine using a MFSKERNEL provided to me by
Jordan and it worked. It was possible to finally do an install of a SNAP
on the machine.
Submitted by: Gary Jennejohn <gj%[email protected]>
Don't gratuitously shutdown network after NFS or FTP install.
Centralize release version string to one location included by everyone.
Bring in new options screen.
o Allow user to specify blocksize to cpio for tape extract.
o Allow user to chose cpio extraction verbosity level (-V or -v).
o Hopefully stomp the fstab sorting bug once and for all.
o Create termcap file for fixit operation.
o Create spwd.db file for fixit operation.
o Upgrade to XFree86 3.1.2 (and add a few new collections for same).
jkh:
Change the fixit floppy paradigm somewhat. Rather than having
a fixit floppy be a stand-alone boot floppy with emasculated
command set due to space crunch, make boot floppy a filesystem
of nice utilities and *no* kernel. The idea is that you boot
the standard boot floppy and choose the "Fixit" item off the top
menu. It then asks for and mounts the fixit floppy, adds the mount
point to $PATH and then forks a shell with the inherited PATH. You
can use the shell to traipse around the filesystem, tweaking things
as desired.
Mutate the useless shell option in first menu to far more useful fixit.
Fix the bogus `ifconfig sl0' case once and for all with a special case
hack for cuaa0.
gpalmer:
Fix benign-yet-bogus incorrect `password' to anon ftp sites.
joerg:
Allow cpio to guess at input format again.
Submitted by: jkh, gpalmer, joerg
to:
A) Use consistent variable expansion syntax.
B) *NOT* expect rc files to be directly in /usr/local/etc. That
was a very poor choice since lots of ports dump things straight
into /usr/local/etc and invoking anything with a .sh suffix in
there would be a bad idea indeed. It's now /usr/local/etc/rc.local.d
for much greater clarity and safety.
RELENG_2_1_0 tags to effect the reorg of the directories and files below
the help directory. (which is why I did it via the HEAD.. cvs cannot add
files to a branch in this version)
request, it cores due to using the unitialized global req_name_ptr
pointer. -Wall does not reveal this.
Repeat by having an old valid ticket and start kerberos. rsh to
a non-realm system.
Also intialize lifetime to DEFAULT_TKT_LIFE and kerno to KSUCCESS since
they can be refernced before being initialized.
Submitted by: John Capo <[email protected]>
1) Bruce and Andrey's tty fixes
2) many of Bruce's prototype and function argument fixes/corrections
3) Bruce's version of the Cyclades driver
4) Improvements to the RISCom/8 driver
John's malloc() patches, it doesn't bring it what looks to be a number
of Bruce's changes which probably depend on the tty changes.
Submitted by: dyson
route expire time calulation, and fill in default value for pipe sizes.
NOTE: Part of rev 1.15 left out at Garrett's request; the default mtu is
not filled in.
Time to go to `newc' format for cpio. This works-around a bug currently
in cpio and gives us a little more robust format anyway (with CRC checking).
[Note that 2 hunks of the old delta no longer apply due to intervening
changes from other branches that obsolete the effected lines.]
Latest eBones target
Submitted by: markm
[Note, I have had to hand apply this due to the order of deltas
being different, so it does not match the original delta, but
achivies the desired results].
Provide default values for the disklabel fields sbsize, interleave,
and rpm. This prevents a subsequent ``disklabel -B'' from failing.
Closes (my - joerg) PR #i386/251 disklabel(8) refuses to install new
bootstrap.
Submitted by: [email protected] (Craig Struble)
Fix a number of problems and add a couple of new features:
o Don't frob the network/CD/DOS/etc configuration when not running as init
(e.g. post-install). Assume that everything's happily up and working already.
o Add express and custom install options. Now you can invoke just about
every individual installation option manually as well as have sysinstall
lead you by the nose (or some other suitable appendage) through all the
appropriate screens.
o Mount the DOS partition read-only by default in /etc/fstab until we figure
out why MSDOSFS is so terribly broken. It doesn't appear to be quite so
pathological if you don't mount it read/write.
Reviewed by:
Submitted by:
Obtained from:
Fix bogon in network address checking code. It nows allows the number
255 in the first three fields, although 255 in the last octet is still
considered an error, as it is still a broadcast address (AFAIK).
Noticed By: [email protected] (Larry Granroth)
Reviewed by:
Submitted by:
Obtained from:
cvs admin -o 1.1.1.1.6.1
cvs update -j 1.3
----------------------------
revision 1.3
date: 1995/06/25 03:35:49; author: bde; state: Exp; lines: +2 -1
41 headers must be implicitly included and one more (<sys/param.h>) must
be explicitly included before kvm_getprocs() can be used.
----------------------------
revision 1.2
date: 1995/06/24 18:53:09; author: joerg; state: Exp; lines: +9 -9
Update the man page for kvm_getprocs.3 to reflect our sysctl-based
kvm mechanism.
Submitted by: (Vic Abell) <[email protected]>
----------------------------
Added a missing vm_object_unlock(). This is a no-op since we don't use
object locking, but it looks like a bug and it's good to be consistent
anyway.
Reviewed by: John Dyson
editor" here and in the docs. People have come to understand "FDISK"
as a more generic term and have been complaining that they didn't
equate the "master" partition editor with the old fdisk stage and were
confused.
on me:
1. Mark Murray's eBones patches.
2. Joerg's German docs + fixes.
3. Various sysinstall bug fixes from me + Mark's eBones menu changes.
4. Steven G. Kargl's doc fixes.
Submitted by: markm, joerg, jkh, [email protected]
".../packages/All". The "all" category that was automatically added
for every package is gone.
Note that bsd.port.mk requires category names to start with lowercase
names, otherwise it may get confused.
Reviewed by: jkh
By the way, here is a small script to convert your local package
hierarchy. Run it in bash, as /bin/sh not only will bark at the
$(.) command substitution but will also botch the [a-z]*/*.tgz
expansion (long-standing and annoying bug, reported before).
cd /usr/ports/packages
mv .packages All
for i in [a-z]*/*.tgz; do
j=$(basename $i)
/bin/rm $i
ln -s ../All/$j $i
done
speak english. In this doc I say that "2.0.5 fills a much needed
gap between 2.0R and 2.1." No wonder the translators were confused!
I'm trying to say that we _wanted_ a gap between 2.0.5 and 2.1? That
such gaps are much needed? Wurgh! Not what I was trying to say at
all! It should have (and now does) read: "2.0.5 fills a critical
gap between 2.0R and 2.1." Critical gap, not much needed. :-)
Translators: You may wish to adjust your own translations as
well if you tried to translate my original botch! Send me diffs
as soon as you can. Thanks!
Submitted by: me
changes over another! Bad form, and I thought they
were both coming from the same author or I wouldn't have done
it. Revert to original author's version until the two Spanish
translators figure out who's doing what.. :-)
actually had this done at one point and lost it somewhere along the
line. Again, this is an honest to gosh bug fix only: no functionality
is changed.
- After a child broadcaster process dies or is killed, set its dom_pipe_fds
descriptors to -1 so that the 'READFD > 0' test in the select() loop
does the right thing.
Since descriptor values can be re-used, failure to do this can lead
to a situation where a descriptor for an RPC socket can be mistaken for
a pipe. If this happens, RPC sockets could be incorrectly handed off to
handle_children(), which would then clear the descriptor from the select()
descriptor mask and prevent svc_getreqset() from handling them. The end
result would be that some RPC events would go unserviced. Curiously,
the failures only happen intermittently.
BTW, if somebody would like to take a look at the German
README I notice that the special characters got totally stripped
somehow and I'm not entirely sure how to put them back! [-jkh] :(
Submitted by: "Philippe Charnier" <[email protected]>
Folks - please review these! I'm quite sleepy at the moment, and I'm
sure that some of this could be worded better. I'd like to have at least
a reasonable syntax pass over this before handing it off to the translation
folks! Thanks! Feel free to commit any changes directly if it's any time
in the next 8 hours, BTW. I won't mind since I'll be asleep!
- the major number wasn't checked, so accesses beyond the end of bdevsw[]
were possible. Bogus major numbers are easy to get because `sysctl -w'
doesn't handle dev_t's reasonably - it doesn't convert names to dev_t's
and it converts the number 1025 to the dev_t 0x35323031.
- Driver d_psize() functions return -1 to indicate error ENXIO or ENODEV
(the interface is too braindamaged to say which). -1 was interpreted
as a size and resulted in the bogus error ENOSPC.
- it was possible to set the dumpdev for devices without a d_psize()
function. This is equivalent to setting the dumpdev to NODEV except
it confuses sysctl.
- change a 512 to DEV_BSIZE. There is an official macro dtoc() for
converting "pages" to disk blocks but it is never used in /usr/src/sys.
There is much confusion between PAGE_SIZE sized pages and NBPG sized
pages. Maxmem consists of both.
Not fixed:
- there is nothing to invalidate the dumpdev if the media goes away.
This reduces the benefits of the early calculation of dumplo. Bounds
checking in the dump routines is relied on to reduce the risk of
damage and little would be lost by relying on the dump routines to
calculate dumplo.
- no attempt is made to stay away from the start of the device to
avoid clobbering labels.
Fix wrong && anachronistic comment about the type of bootdev.
Reviewed by: davidg
Submitted by: Bruce Evans
handled correctly. This would manifest itself as "object deallocated too
many times" panics and perhaps other strange inconsistencies on NFS servers.
Reviewed by: me, of course
Submitted by: John Dyson
Remove unused devices (*[sw]d*[bdefgh]).
Dont gzip boot_crunch. (This SAVES space on a 4 MB machine, since the
file can be segment can be paged from now.
This (with the kzip patch) makes a 4M machine boot and run again.
Margin in my build is 22 blocks and 9 inodes.
I will look at tgz'ing the help files, we need that.
Add a NOMAN= . It doesn't have a manual page yet.
Please don't cry :-). I ask Rod first. the whole isdn subdir is not
used in the moment and is only dead source code in the tree.
Add Bt956 as being supported.
Include 2940 in the 2742/2842 section.
Anyone with a new feature or driver in 2.0.5 should think about adding "blurbs"
to this file. Some features say exactly what they do, others say nothing...
this document needs some rounding out.
LINT talks about about 2.1. I changed that to 2.0.5,
and clarified why certain devices need "at scbus?".
There is still a crazy "PCVT=210" which shouldn't be there,
but corrected comment as it is needed for 2.0.5.
multi part stuff centralized.
The final check is backwards or something so it always said it failed,
even it it didn't.
Fixed tcpip address check to not be stupid, 10.0.255.1 is legal.
being called more than once. Also fix a problem where the URL was getting
smashed in the environment by copying it to a temporary area before we
jump up and down on it.
floppy (for slip install).
2. Try to work around a bodge in the ftp extraction loop where FtpEOF() was
being called more than once. Also fix a problem where the URL was getting
smashed in the environment by copying it to a temporary area before we
jump up and down on it.
for broadcasts if point-to-point links shared the same IP address as
the ethernet. The fix must be enabled with P2P_LOCALADDR_SHARE option
in the kernel config file. This will someday likely be standard, but
there isn't sufficient time before release to determine if there are
any interoperability problems with routed and/or gated.
Reviewed by: Garrett Wollman, and me
Submitted by: Peter Wemm
- option DODUMP no longer exists (remove all references to it).
- directive `swap on' is now a no-op (don't bother documenting it; remove
comment to match code).
- directive `dumps on' still works (restore code to match comment; deprecate
it in comment).
Reviewed by: Poul-Henning Kamp, and me
Submitted by: Bruce Evans
Submitted by: bde
rc.i386 failed messily when I used a serial console.
Editors note:
Use file redirection so that all the kbdcontrol and vidcontrol
commands act upon /dev/ttyv0 instead of stdin. Though this feature
is not documented it is the intended behavior of {vid,kbd}control
and shall be documented in the future as such.
Change root.flp from a new format CPIO archive to a tar archive.
Unless we're willing to change the main tarballs from tar format to
"newc" (or, even better, "crc") cpio format, we need to use one common
one for all and that's tar for now. Install will now grab "root floppy"
from an ftp site if that's what you've got set.
Fix even more gripes from Poul's list.
P.S. As soon as I get the distfiles copied over to freefall tomorrow
morning, those of you wishing to test minimal installs over ftp should
be able to do so by grabbing the boot floppy and nothing else. Keep
your eyes open for my announcement.
Change root.flp from a new format CPIO archive to a tar archive.
Unless we're willing to change the main tarballs from tar format to
"newc" (or, even better, "crc") cpio format, we need to use one common
one for all and that's tar for now. Install will now grab "root floppy"
from an ftp site if that's what you've got set.
Fix even more gripes from Poul's list.
Root floppy (which actually may be able to go completely away at some point
soon!) is now loadable from ftp/nfs/dos as well as CDROM and (of course)
floppy.
Fix more problems on Poul's Gripe List.
Rod, Jordan and David have more or less given me the OK on this
with the understanding that it doesn't change any functionality.
It doesn't: these are bug fixes only. No other part of the system
should be affected. Of course, since I'm the only one working on
NIS, you'll just have to take my word on it. :)
Fixes for the following annoyingly subtle bugs:
- ypbindproc_setdom_2 is supposed to be declared void *, not boot_t *,
and it fails to correctly signal failures back to the ypset(8) command:
we need to call one of the svcerr_*() functions (in this case,
svcerr_noprog() seems a logical choice -- we're really cheating
a bit here because nothing else quite fits) to tell ypset that the
attempt to set the binding for a domain failed. If we don't do this,
failed ypset attempts either appear (incorrectly) to succeed, or
they time out.
- The lock handling for child processes isn't quite right. The
child broadcaster processes have to release all locks on the
binding files and the ypbind.lock file.
- The parent ypbind process will SEGV if you do the following:
-- start ypbind with the -ypset or -ypsetme flag
-- type 'ypwhich -d random_unserved_domain'
-- type 'ypset -d random_unserved_domain anyhost'
-- type 'ypwhich -d random_unserved_domain' again
-- wait about 60 seconds
What happens is this: the ypwhich command causes ypbind to fork a
broadcaster process that searches for a server for random_unserved_domain.
If you then use ypset to force a binding while this process is still alive,
the state flags that tell the ypbind parent process that the child
is running will be cleared. The second ypwhich command then causes
a *second* child process to be forked for random_unserved_domain,
which is verbotten. When the first broadcaster exits and tells the
parent that it wasn't able to find a server for the domain, the parent
clobbers the entry for random_unserved_domain. Then the second broadcaster
exits and the same thing happens, only trying to clobber the entry
twice causes a SEGV.
The fix for this is a slight change in program structure: since we
can't have more than one broadcaster for a given domain at a time,
we save the pipe descriptors and pid for the child broadcaster in members
of the _dom_binding struct for the domain. (As a side effect, we
can get rid of the global child_fds variable.) So when rpc_received()
finds that it's been asked to do a ypset for a domain for which a
broadcaster process exists, it sends a SIGINT to the child to kill it
and closes the pipe to the now-dead child. This keeps everything in sync
and insures that we don't leak file descriptors.
- ping() should be using YPPROC_DOMAIN rather than YPPROC_DOMAIN_NONACK
when it does its clnt_call() to the server.
- Removed the check for client_handle == NULL in ping() and make
client_handle local to ping instead of a member of the _dom_binding
struct. This fixes another potential ypset problem: using ypset to
force a binding to a machine that has an NIS server but which *doesn't*
support the domain we're after can result in permanently bogus bindings.
- the 'server OK' message prints the wrong IP address.
etc.). The tulip_start routine was rewritten to use less stack space (I've
been having problems with wcarchive overflowing the stack and this should
help a little). This version also has preliminary NetBSD support.
Rod Grimes helped in testing this version of the driver. Thanks Rod. It's
additionally been extensively tested here and on wcarchive.
Submitted by: Matt Thomas
The site in Island has only the 1.1-RELEASE dist.
The previous South Africa sites are dead and the brasilian one
is very hard to get into and painfully slow.
The two South Africa sites come from MIRROR.SITES.
Basically, this is just a simple name change. People were historically
confused by the "cpio floppy", having no clear idea as to what it was
(even if they knew what "cpio" stood for) given that the name gives
one absolutely no indication as to what it's FOR. It's about as content
free as calling it a "data floppy". Root floppy isn't much better, but
it's got some historical weight (Linux divides their set into boot and
root floppies) and is reasonably descriptive for a floppy that comprises
the beginnings of a stand-alone root filesystem.
in machdep.c (it should use the global nmbclusters). Moved the calculation
of nmbclusters into conf/param.c (same place where nmbclusters has always
been assigned), and made the calculation include an extra amount based
on "maxusers". NMBCLUSTERS can still be overrided in the kernel config
file as always, but this change will make that generally unnecessary. This
fixes the "bug" reports from people who have misconfigured kernels seeing
the network hang when the mbuf cluster pool runs out.
Reviewed by: John Dyson
in machdep.c (it should use the global nmbclusters). Moved the calculation
of nmbclusters into conf/param.c (same place where nmbclusters has always
been assigned), and made the calculation include an extra amount based
on "maxusers". NMBCLUSTERS can still be overrided in the kernel config
file as always, but this change will make that generally unnecessary. This
fixes the "bug" reports from people who have misconfigured kernels seeing
the network "hang" when the mbuf cluster pool runs out.
Reviewed by: John Dyson
regular user could panic the machine with a simple "tail /proc/curproc/mem"
command. The problem was twofold: both kernfs and procfs didn't fill in
the mnt_stat statfs struct (which would later lead to an integer divide
fault in the vnode pager), and kernfs bogusly paniced if a bmap was
attempted.
Reviewed by: John Dyson
device.
v_numoutput wasn't incremented to match the b_iodone nesting. It's still
fishy that vwakeup() clears B_WRITEINPROG before biodone() has finished;
however, B_WRITEINPROG seems to be never used.
Submitted by: Bruce Evans
usage is very bad.
And I found some bugs(?) in ja_JP.*/usage.hlp.
1. I have made typo.
2. Mr. Hubbard didn't change about number of virtual consoles.
Submitted by: NIIMI Satoshi <[email protected]>
the National Semiconductor InfoMover PCMCIA cards also. In tests on a
NE4100 on Jordan's laptop here, the ze driver works fine with that
card.
Reviewed by: Jordan Hubbard, Rod Grimes, and me
Submitted by: Gary Palmer
1. Fix a few bugs in the ftp installation code and implement proper
ftp and network shutdown routines.
2. Clean up the menus a fair bit - add a FreeBSD configuration menu.
3. Eliminate the last of the "chaining" - the installation now does
the most obvious thing in the most obvious cases and doesn't present
you with more menus than you were expecting. This makes it necessary to be
a little more explicit in places, but it's still less confusing.
4. Add a few more safety nets for the user. Change a few hard-and-fast
limits to warnings (it now runs as non-root, Bruce).
5. Add descriptions for all the supported ethernet cards.
6. Make the cpio floppy extract put up a menu requesting the drive you wish
to use if you have more than one; don't just always assume drive A.
Add testftp: target
ftp.c:
add more debugging output and fix a few more problems
media_strategy:
make the ftp system actually do something resembling common sense.
it now works after a fashion, although it soon falls over for some
reason.
ftp installation method should now function. We'll know as soon as my
make release builds the floppies. I'm just committing this out of my
release tree now so that it doesn't get clobbered again.
use them yet, but it's close (we're working on the last wrinkles
in the CD install for now).
2. Complete the CDROM installation strategy code.
3. Simplify the distribtuion loading code.
4. General error message cleanup.
5. Write the /etc/fstab file now and split those routines into config.c
6. Clean up the menus a little more.
to most users (the wrong length is passed to ether_input). The
second is more serious. The multicast hash algorithm uses the wrong
(low) bits instead of the right (high) bits. This is only an issue
if you use >12 multicast addresses but if you are using IP multicast
then it might affect you...
Submitted by: Matt Thomas
thrown out if bpfilter support and no BPF listener. (submitted by Bill
Fenner)
Removed unused variable and changed another from a stack variable to a
static - the variable was a rather large array of structs that consumed
a lot of stack space. (me)
1) Files weren't properly synced on filesystems other than UFS. In some
cases, this lead to lost data. Most likely would be noticed on NFS.
The fix is to make the VM page sync/object_clean general rather than
in each filesystem.
2) Mixing regular and mmaped file I/O on NFS was very broken. It caused
chunks of files to end up as zeroes rather than the intended contents.
The fix was to fix several race conditions and to kludge up the
"b_dirtyoff" and "b_dirtyend" that NFS relies upon - paying attention
to page modifications that occurred via the mmapping.
Reviewed by: David Greenman
Submitted by: John Dyson
This is getting ridiculous. I may have to put the clear() back
and take the performance penalty, Poul.
Tweak the TCP/IP setup menu to look a little nicer.
Add lp0 to the list of available network devices (it was found before
but simply not described properly).
Justin can see it.
2. Attempt to fix the redisplay problems in label.c some more. Not clearing
the screen each time is certainly faster, but it's causing all sorts of
problems.
of optimizations. Add a check to make sure that root filesystems
are at least 20MB in size (this is just a thumbnail approximation,
and we can revise it later if necessary).
disks.c: clrtobot() so that deleted stuff disappears.
disks.c: offset is signed (for OnTrack diskmanager)
system.c: don't setbuf(stdout,0), it's too slow.
Add size argument to new_part, so it can come up with a good default for newfs.
Fix (possibly) a dialog botch after label.c's wizard mode.
Make vsystem even smarter abour crunched binaries (what a speedup!)
(You need to recompile crunchgen !)
partition editors (ugh). Fix an utterly bogus message (no arguments :)
in dist.c. This should all make Poul a little happier and slide in
before the next CTM update window.
with the diff/CVS hassles - this represents far too many CVS commit
messages for you folks, and trying to document each and every iteration
of the code is a hassle (and not very useful at that).
Don't notify in vsystem() - it obscures the original message.
Put some debugging code into cpio_extract() so that I can see
why it doesn't work now. :(
crypt salt string begin with a '_', no other crypt's do. If you remove the
initialization of $salt to '_' in sub salt(), everything works as advertised.
Submitted by: Charles Henrich <[email protected]>
implementation.
2. Totally rework device registration. It's about half the size and
more powerful now.
3. Add DOS discovery.
4. Start filling in some of the strategy routines.
5. Another clean-up pass over the menus.
6. Make wizard code use Disk typedef.
If I can get the first strategy routine finished tonite, we should have a working
install (from ftp, at least) this weekend.
as per Andrey's letter. Make a few modifications for correctness.
2. Add Language menu back to first menu - it was too buried in the
Options menu.
3. Add size information to all distributions.
4. Add a compat20 distribution (we need to make one of these!! Any takers? Please?)
Submitted by: Nickolay N. Dudorov <[email protected]> & jkh
2. Adjust some of my previous wording to be more indicative of the way things
currently are and using less bogus corporate categorizations ("Directors"
and "Officers" only exist in real corporations, which the FreeBSD Project
is not, so it sounded kind of pompus on reflection).
These changes solve the problem in a general way by moving the
initialization out of the individual fs_mountroot's and into swaponvp().
Submitted by: Poul-Henning Kamp
syscons (and/or cons25) at all. This code looked just fine running
on an xterm, but on a console the attributes are all wrong. I
now have to sacrifice some screen real-estate to pring cheesy
`-' characters to accomplish the same thing.
broken in syscons, or at least in the cons25 termcap entry! :-( A_BOLD
won't show up on monochrome adapters (I don't think) but they'd be screwed
anyway since I don't have an attribute to use for them now at all.
2. Don't use russian screenmap - apparently not necessary with right font.
3. Dequote bogusly quoted font name in english language setting.
4. Use setterm() and hack around an undesirable side-effect (cbreak is unset).
5. be smarter about setting OnVTY, and use it in cases where it makes sense.
Submitted by: Nickolay N. Dudorov <[email protected]>
won't know until Poul wakes up again).
2. Make vsystem() put its output on the debugging fd.
3. DTRT with root filesystem placement - now I see how this has to work
(thanks, Poul).
4. Many miscellaneous spelling errors fixed and general cleanup.
changes. The check for nswap was bogus, but the code was so convoluted
that it was difficult to tell. It's better now. :-)
Reviewed by: David Greenman (extensively), and John Dyson
Submitted by: Poul-Henning Kamp, w/tweaks by me.
Rearranged a few sections, add memoryuse section.
current.sgml, ports.sgml, porting.sgml
Added a <label>s for cross reference targes.
submitters.sgml
Lots of editing, added cross references to other sections of
the handbook. Added a sample BSD-style copyright statement.
eresources.sgml
Updated the mailing list section, thanks to Peter Dufault.
authors.sgml
Added Peter Dufault, David Greenman and Joerg Wunsch.
memoryuse.sgml
A new section about how/where in PC memory the FreeBSD kernel
gets loaded and run.
inconsistencies in the VM system that eventually lead to a panic. These
changes fix the behavior to conform to the behavior in SunOS, which is
to deny faults to pages beyond the EOF (returning SIGBUS). Internally,
this is implemented by requiring faults to be within the object size
boundaries. These changes exposed another bug, namely that passing in
an offset to mmap when trying to map an unnamed anonymous region also
results in internal inconsistencies. In this case, the offset is forced
to zero.
Reviewed by: John Dyson and others
built release after fixing all the wrong directory permissions in that release.
Then use diff -c -b to verify them against the old versions, nothing but
new directories added :-). And a lot of alphabetizing done!
serial_putchar() always hung if it was called and the serial port existed,
so booting with -h hung when the above bug was fixed. Previously, setting
-h did nothing but -h was sometimes the default due to the stack garbage
bug.
Submitted by: DI. Christian Gusenbauer <[email protected]>
The `howto' arg to boot() was not supplied, so it was stack garbage (actually
the return address in the boot program). I didn't use the submitted fix.
1) If a target initiated a sync negotiation with us and happened to chose a
value above 15, the old code inadvertantly truncated it with an "& 0x0f".
If the periferal picked something really bad like 0x32, you'd end up with
an offset of 2 which would hang the drive since it didn't expect to ever
get something so low. We now do a MIN(maxoffset, given_offset).
2) In the case of Wide cards, we were turning on sync transfers after a
sucessfull wide negotiation. Now we leave the offset alone in the per
target scratch space (which implies asyncronous transfers since we initialize
it that way) until a syncronous negotation occurs.
3) We were advertizing a max offset of 15 instead of 8 for wide devices.
4) If the upper level SCSI code sent down a "SCSI_RESET", it would hang the
system because we would end up sending a null command to the sequencer. Now
we handle SCSI_RESET correctly by having the sequencer interrupt us when it
is about to fill the message buffer so that we can fill it in ourselves.
The sequencer will also "simulate" a command complete for these "message only"
SCBs so that the kernel driver can finish up properly. The cdplay utility
will send a "SCSI_REST" to the cdplayer if you use the reset command.
5) The code that handles SCSIINTs was broken in that if more than one type
of error was true at once, we'd do outbs without the card being paused.
The else clause after the busfree case was also an accident waiting to
happen. I've now turned this into an if, else if, else type of thing, since
in most cases when we handle one type of error, it should be okay to ignore
the rest (ie if we have a SELTO, who cares if there was a parity error on
the transaction?), but the section should really be rewritten after 2.0.5.
This fix was the least obtrusive way to patch the problem.
6) Only tag either SDTR or WDTR negotiation on an SCB. The real problem is
that I don't account for the case when an SCB that is tagged to do a particular
type of negotiation completes or SELTOs (selection timeout) without the
negotiation taking place, so the accounting of sdtrpending and wdtrpending
gets screwed up. In the wide case, if we tag it to do both wdtr and sdtr,
it only performs wdtr (since wdtr must occur first and we spread out the
negotiation over two commands) so we always have sdtrpending set for that
target and we never do a real SDTR. I fill properly fix the accounting
after 2.0.5 goes out the door, but this works (as confirmed by Dan) on
wide targets.
Other stuff that is also included:
1) Don't do a bzero when recycling SCBs. The only thing that must explicitly
be set to zero is the scb control byte which is done in ahc_get_scb. We also
need to set the SG_list_pointer and SG_list_count to 0 for commands that do
not transfer data.
2) Mask the interrupt type printout for the aic7870 case. The bit we were
using to determine interrupt type is only valid for the aic7770.
Submitted by: Justin Gibbs
Add comment that you should not have to edit netstart, and if you
do we would like to know about it.
The lo0 interface is now handled just like any other interface,
This makes it possible to do things to it from sysconfig.
Redo the comments in sysconfig about network_interfaces and ifconfig_${X}
to reflect the moving of lo0 to this scheme. We now have an uncommented
variable for sysintall to find and play with. (Your welcome Jordan)
Redo the way static routes are handled. Basically use the same
scheme for routes that I did for network interfaces. This allows
any number of static routes to be added from sysconfig.
Make sure we do the default route first so we stand a chance of
getting to our DNS server (if we have one) to resolve our own
IP address from $hostname.
It remains to be seen how successfully. The distribution loading code
is still not here yet, but the partition/newfs/mount/cpio-extract cycle
is as complete as it's ever going to get, modulo possible bug fixes.
The TCP/IP setup screen is also sort of here, albeit in a highly-changing
state due to the fact that per-interface information isn't being kept
right now but is being added (thanks, Gary!).
one of the key components of the system, but I'm sure that this:
===
- ${ECHO_MSG} "===> Registering installation for ${PKGNAME}"; \
+ ${ECHO_MSG} "===> Registering installation for ${PKGNAME}"; \
===
change has absolutely no chance to screw us up, right? :)
full directory hierarchy, as is the format of the new ports collection.
It used the old "all packages in one directory" paradigm, which is wrong for
ports now.
Submitted by: Marc van Kempen <[email protected]>
IGMPv2 spec. This fixes the following bugs:
o ntohs() on a char provides silly results
o timer needs to be scaled to units of PR_FASTHZ; this was being done
inconsistenly so now it gets done when it is initialized.
Reviewed by: Garrett Wollman
Submitted by: Bill Fenner <[email protected]>
the fixes!):
o Scoped addresses might let traffic in
o IGMP queries sent with wrong timeouts
o Possible core dump in mtrace if we get a request for which we have no route
o If a member on a transit network left a group, mrouted would stop forwarding
even if there was a downstream router
o Various code cleanups and logging changes
Reviewed by: wollman
Submitted by: Bill Fenner <[email protected]>
have non-critical nfs volumes in /etc/fstab they should have option bg
on them. The behavior of the system is more tuneable this way, and
allows a slow mounting /usr over nfs to work.
Submitted by: bde
when the single user shell was terminated. These changes disallow mounting
or R/W upgrading filesystems that are dirty unless "-f" (force) option
is used with mount. /etc/rc has been modified to abort the startup if
one or more non-nfs partitions fail to mount.
Reviewed by: Poul-Henning Kamp, Rod Grimes
I ran into another manifestation of the problem reported in PR 211 and
fixed it. Try this:
as non-root:
cd /tmp; mkdir x y x/z
as root:
chown root /tmp/x/z
as non-root:
cd /tmp/x; mv z ../y # EACCES as expected
as root:
cd /tmp/x; mv z ../y # EINVAL NOT as expected
This is because ufs_rename() sets IN_RENAME and fails to clear it.
Reviewed by: davidg
Submitted by: bde
the 802.3 frames generated by the DC21040 (which does automatic padding
of less-than-minimum frames) and the frames generated by the 'ed'
driver, I've found that there is indeed a bug in the size of "ETHER_MIN_LEN"
as reported by several people, John Hay being the most recent. The driver
was actually setting the length to 6+6+2+50 (64 bytes), which when adding
in the CRC (which is automatically appended to the frame and not included
in the length), the minimum frame is 4 bytes larger than it is supposed to
be. All of this is confirmed by tcpdump showing 50 bytes of data for
minimum frames from the 'ed' cards and 46 bytes from 'de' cards. This
analysis has also revealed that there is garbage in the un-filled in
portion at the end of the minimum frames from the 'ed' driver; I don't
plan to fix this.
Print a final newline to stderr after the scan finishes, only do it
at the right place in this version, 1.1.5.1 caused an extra newline
if you where not running -s, and it went to stdout instead of stderr.
Obtained from: FreeBSD 1.1.5.1
device table layout...basically, don't output the cruft anymore - it
is now dynamic.
Reviewed by: John Dyson and David Greenman
Submitted by: Poul-Henning Kamp
require specific partitions be mentioned in the kernel config
file ("swap on foo" is now obsolete).
From Poul-Henning:
The visible effect is this:
As default, unless
options "NSWAPDEV=23"
is in your config, you will have four swap-devices.
You can swapon(2) any block device you feel like, it doesn't have
to be in the kernel config.
There is a performance/resource win available by getting the NSWAPDEV right
(but only if you have just one swap-device ??), but using that as default
would be too restrictive.
The invisible effect is that:
Swap-handling disappears from the $arch part of the kernel.
It gets a lot simpler (-145 lines) and cleaner.
Reviewed by: John Dyson, David Greenman
Submitted by: Poul-Henning Kamp, with minor changes by me.
existance of ${CHROOTDIR}.
Remove -k option from make install for building chroot tree, makes it
error out early if you forgot to populate the pre-chroot obj tree.
Reviewed by: phk
Ports for which we can't build packages should define NO_PACKAGE but
still prepare pkg/* files. The user who really wants a package and
clear of the legal problems can say FORCE_PACKAGE from the command line
to build a package anyway.
A phone call from Manfred quickly pointed up the fact that I got the conflict
check backwards. NOW we implement the conflict checking correctly! Wheesh!
- Do the right thing when booting in NFS diskless mode, which is nothing.
Make the default unconfigured entries for swdevt[0] and dumplo something
that swapconf() will ignore and not choke on (the swap setup is done
in nfs_vfsops.c when booting diskless).
is more representative of worst case situations of 4 files/directory. (If
that last sentence doesn't make any sense, I'm not surprised. It's rather
compilcated how this all fits together....).
This should fix a problem that Ed Hudson has been complaining about where
directories with lots of symlinks could cause excessive disk I/O.
with davidg about it, I hereby kill two undocumented misfeatures:
The code to skip a miniroot in the swapdev is not particular useful, and
if we need it we need it to be done properly, ie size the fs and skip all
of it not some hardcoded size, and subtract what we skip from the length
in the first place.
The SEQSWAP dies too. It's not the way to do it, it doesn't work, and
nobody have expressed any great desire for it to work. The way to
implement it correctly would be a second argument to swapon(2) to give
a priority/policy information. Low priority swapdevs can be made so
by adding them at a far offset (0x80000000 kind of thing), with almost no
modification to the strategy routine (in particular a offset per swapdev).
But until the need is obvious, it will not be done.
it really should have been printing all this time. Also fix my rather
bogus handling of the id_conflicts value by moving it to the end of
isa_device and dealing with that correctly now.
to access it. setdelayed() actually ORs the bits in `idelayed' into
`ipending' and clears `idelayed'.
Call setdelayed() every (normal) clock tick to convert delayed
interrupts into pending ones.
Drivers can set bits in `idelayed' at any time to schedule an interrupt
at the next clock tick. This is more efficient than calling timeout().
Currently only software interrupts can be scheduled.
boot diskless with it, you get a panic because setconf() is only
called for mountroot == ffs_mountroot. It really needs to be called
no matter what manner of rootfs we have. I can't really say if
swapgeneric will work with a CD-ROM though. (I get the feeling I'm
the only one who uses swapgeneric these days anyway.)
others. The flag can be put in descriptive locations, e.g.:
device sb0 at isa? port 0x220 irq 7 conflicts drq 1 vector sbintr
or
device psm0 at isa? port "IO_KBD" conflicts tty irq 12 vector psmintr
But is nonetheless boolean only. You can't turn conflict checking off for
only a given type of conflict. I didn't deem it worth the trouble at this
stage, and it's far better than the ALLOW_CONFLICT_* that preceeded it.
currently considering reducing the TCP fasttimo to 100ms to help improve
things, but this would be done as a seperate step at some point in the
future.
This was done because it was causing some sometimes serious performance
problems with T/TCP.
there may even be LKMs.) Also, change the internal name of `unixdomain'
to `localdomain' since AF_LOCAL is now the preferred name of this family.
Declare netisr correctly and in the right place.
- Make the child process reaper signal-driven. (Previously, we called reaper()
once a second each time we went through the select() loop. This was
convenient, but inefficient.)
- Increase main select() timeout from 1 second to 60 seconds and use
this as the ping timer instead of using timestamps in the _dom_binding
structure. This nd the reaper() change noted above makes ypbind a little
less CPU-intensive.
- Don't flag EINTR's from select() as errors since they will happen as a
result of incoming SIGCHLD's interrupting select().
- Prevent possible resource hogging. Currently we malloc() memory
each time a user process asks us to establish a binding for a domain,
but we never free it. This could lead to serious memory leakage if a
'clever' user did something like ask ypwhich to check the bindings
for domains 0.0.0.0.0.0.0.0.0.0 through 9.9.9.9.9.9.9.9.9.9 inclusive.
(This would also make a mess out of the /var/yp/binding directory.)
We now avoid this silliness by a) limiting the maximum number of
simultaneous bindings we can manage to 200, and b) free()ing _dom_binding
structures of secondary domains whose servers have stopped responding.
We unlink the /var/yp/binding/domain.vers files for the free()ed
domains too.
(This is safe to do since a client can prod us into reestablishing the
binding, at which time we'll simply allocate a new _dom_binding structure
for it.)
We keep count of the total number of domains. If asked to
allocate more than the maximum, we return an error. I have yet to hear
of anybody needing 200 simultaneous NIS bindings, so this should be
enough. (I chose the number 200 arbitrarily. It can be increased if need
be.)
- Changed "server not responding"/"server OK" messages to display server
IP addresses again since it looks spiffier.
- Use daemon() to daemonify ourselves,
- Added a SIGTERM handler that removes all binding files and unregisters
the ypbind service from the portmapper when a SIGTERM in received.
- The comment 'blow away everything in BINDINGDIR' has no associated code.
Give it some: clean out /var/yp/binding at startup (if it exists).
This completes my ypbind wishlist. Barring bug fixes, I shouldn't need to
go poking around in here anymore. (Of course, this means I can start
working on my ypserv whishlist now... :)
Do another clean-up pass over this, making the generic menu handler much
more powerful (now handles multiple dispatch). A few more menus fleshed
out and the beginnings of the distribution handler committed. Should
be transfering full distributions over in the next commit.
msdosfs_lookup() did no validation to see if the caller was validated
to delete/rename/create files. msdosfs_setattr() did no validation
to see if the caller was allowed to change the file permissions (turn
on/off the write bit) or update the file modification time (utimes).
The routines were fixed to validate the calls just like ufs does.
On Tue, 09 May 1995 04:35:27 PDT, Richard Stevens wrote:
> In tcp_dooptions() under the case TCPOPT_CC there is an assignment
>
> to->to_flag |= TCPOPT_CC;
>
> that should be
>
> to->to_flag |= TOF_CC;
>
> I haven't thought through the ramifications of what's been happening ...
>
> Rich Stevens
Submitted by: [email protected] (Richard Stevens)
"the amount of text above the current point" instead of "the amount of text
remaining", which was of the exact opposite meaning! Urk.
Submitted by: joerg
It closed the wrong device (usually the B partition instead of the C
partition).
It closed a device without having opened it.
It didn't open a device often enough. This caused swap partitions on
slices other than the first slice looked at to be unavailable for swapping.
It didn't check the device number sufficiently.
Reopen the bdev for the raw partition and not the cdev if only the bdev
was open.
Don't use a bogus limit for the number of partitions to possibly reopen
(bug found by Julian).
Add function dssize() to help fix wdsize() and sdsize(). The slice
layer knows more about (un)open partitions and partition sizes than
the driver layer.
Remove silly "Naffy, the Wonder Porpoise" attribution and add more
justifiable (and overdue) attribution to Bruce Evans. Look at it
as a delete and add operation batched together, not a substitution. :-)
using %lu. This became more broken when I fixed dbtob() to support byte
offsets >= 4GB. The type had to change to [u]quad_t. Previously the
expressions had type unsigned long and were printed using %d. After
division by 1024, the expressions are guaranteed to fit in an unsigned
long, at least for the standard DEV_BSIZE, so edquota doesn't need to
know about quad_t's explicitly.
Fix all the other format mismatches exposed by compiling with -Wformat
(6 more quota limits of type unsigned long printed using %d and 6 time_t's
(i.e., longs) printed using %d).
notice, performed all of the structural changes necessary to get this thing
to work with the unidirectional-DMA version of voxware.
This work is -not- complete, but it's in far better shape than it was, and
I may not touch it again for another few months.
in read() and write(). FNONBLOCK is valid in ioctl() and close().
The bug caused hung ptys when a process talked to itself using nonblocking
i/o and exited while the slave pty had output to flush. ttywait() was
called and hung. Signals didn't work because the process was exiting.
`comcontrol /dev/ttyp0 drainwait 1' worked to terminate the wait. This
shows that comcontrol is not limited to hardware control. It has no i386
or driver dependencies and doesn't belong in src/sbin/i386.
Bruce
to emit spurious page outside of object type messages. It is not
a fatal condition anyway, so the message will be omitted for
release. Also, the code that "clips" the allocation size, associated
with the above problem, was fixed.
The ``flags 1'' in the fdc line is now only needed for owners of an
Insight tape (perhaps there aren't any? Mine is disfunctional). All
other probes are safe wrt. to the motor-control line of floppy disk
drives. Document the flag in LINT finally.
fixed, we should be able to fully set up the user's disk. Still to come
with next commit: filesystem setup, distribution extraction, final
configuration.
fragmented.
Added support for Cogent em100 boards.
Fixed bug that caused BPF to toggle the card to UTP.
Various other improvements.
Submitted by: Matt Thomas and David Greenman
Change IPTOS_PREC_ROUTINE to 0 (was conflict with IPTOS_LOWDELAY) according
to RFC 791 (unchanged since it) and BSDI 2.0 style
Submitted by: Igor Sviridov <[email protected]>
There is a bug in sh: the built in command "fc -l" generates
a core dump (*NULL in not_fcnumber).
According to the sh manual page (fc -l [-nr] [first [last]]), fc -l
is a correct sequence (in that case, values are defaulted to -16 and -1)
but fails when first is not given.
initializing proc0's frame base, too, using cpu_set_init_frame(). It's
a kludge because that macro is intended to be used only for init, but
does what we want nonetheless.
loading kernel
worm.o: Undefined symbol `_STUNIT' referenced from text segment
I copied the STUNIT definition from the old scsiconf.c into this file to
work around this problem.
if the 'time on a node is 0,..
tell the world it is the same as 'boottime'.
This is becasue 'time' is not set up when we create the nodes,
so we can't set them then.
may not be desired if you're just going to blow the kernel away again later)
and substitute one that tells the user where the new kernel build
directory actually IS, which can at least be argued to be useful information
in all cases.
Reviewed by: davidg
ypbind.c:
Make fewer assumtions about the state of the dom_alive and dom_broadcasting
flags in roc_received().
Cosmetic changes and paranoia checks:
ypbind.c:
Make fewer assumtions about the state of the dom_alive and dom_broadcasting
flags in roc_received().
If select() fails, use syslog() to report the error rather than perror().
Check that all our malloc()s succeed. Report malloc() failure in
ypbindproc_setdom_2() to callers.
yplib.c:
Use #defined constants in ypbinderr_string() rather than hard-coded values.
ypbind.c:
Make fewer assumtions about the state of the dom_alive and dom_broadcasting
flags in roc_received().
If select() fails, use syslog() to report the error rather than perror().
Check that all our malloc()s succeed. Report malloc() failure in
ypbindproc_setdom_2() to callers.
yplib.c:
Use #defined constants in ypbinderr_string() rather than hard-coded values.
Added CONTROL device that only does user-ioctl and nothing else;
Added protection so user-ioctl requires write access;
Clean up scsiconf.h a little. It needs more work.
- set TCP_NOPUSH to keep from sending short packets at each write(2) boundary
- set SO_SNDBUF to 64k so we have a reasonable amount of buffer space
- for a regular file in binary mode which is not being restarted and is
. smaller than 16 Meg, use mmap(2) and write(2) the whole file in one big
gulp
In the most common circumstances, this should dramatically reduce the
system-call load from ftpd, since the call to write() will not return until
the entire file has been written, rather than writing just a few K at a time
in a loop.
In the case where ypserv is started with the -dns flag, fall through to
the DNS lookup code only if asked to match a map with the word 'host'
in its name. This prevents failed matches on non-host maps from being
incorrectly handed off to DNS.
the lookup fails. Updated callers to deal with this. Call in_pcblookuphash
instead of in_pcblookup() in in_pcbconnect; this improves performance of
UDP output by about 17% in the standard case.
Remove bogus targets.
Allocate partition letters as follows:
lowest offset "flags & CHUNK_IS_ROOT" gets 'a',
lowest offset "subtype==FS_SWAP" gets 'b'
the rest is allocated in offset order from this sequence "defghab".
This will generally make sense.
Added rules to complain if more than one CHUNK_IS_ROOT or more than one
FS_SWAP per FreeBSD chunk.
Set CHUNK_IS_ROOT on the 'a' partition in Open_Disk.
Run Fixup_Names in Open_Disk.
Correct Makefile so that we build during all: and only install for
make install.
If /etc/sysconfig exists source it to get the flags for restarting
named with. If /etc/sysconfig says no named runs, don't try to start one.
Don't attempt to kill anything if we can not find the named.pid file.
Reviewed by: Nickolay N. Dudorov <[email protected]>
space for the hash list buckets and is a little faster. The features
of tailq aren't needed. Increased the size of the object hash table
to improve performance. In the future, this will be changed so that
the table is sized dynamically.
as side-effect, removed some legacy code that was necessary
when we called vm_fault inside of vm_fault_quick instead of using
the kernel/user space byte move routines.
(2GB). If this limit is not imposed, then filesystem corruption will
ensue when files larger than 2GB are created. This is temporary,
and the underlying limitation will be removed later.
nor is it in sync with my working sources, but it leaves me less CVS hassles
to bring in the new files at this time. Still no documentation to translate
quite yet, but soon. This stuff is actually very close now.
algorithm is used on aic7770 Rev E or higher chips to improve perfomance.
This required a hardware change but we don't know exactly what (most
likely some special register to do fast SCB indexing into host memory),
and we are not at all sure that there are more than 4 SCBs on these
chips. This probe will still classify the revision of the aic7xxx, but
we now default to 4 SCBs (at least until we know more of what was done).
This also fixes a bug in the timeout routine where we cleared a flag
too soon making it imposible to enter one section of the routine.
Submitted by: Timeout bug - Dan Eischen <[email protected]>
interrupts to zero to start with. This is the value we return in
most cases. The sense code then outbs the apropriate value to cause
sense retrieval. The return value was uninitialized before this
change (something that was an okay thing with the old sequencer code,
but not with the semantics of the new).
This problem caused us to always retrieve sense upon recieving a non
zero status byte. This is exactly what was happening for the "target
busy" status returned by exabyte tape drives when they rewind or
power on with a tape installed. The request sense proved fatal.
This should fix the tape problems.
but it outlines what I'm GOING to do to this file.
It's sort of an unignorable notification of coming changes..
This is a bit rude I understand.. but I can't afford to haqve the
diskslice code drifting off too much further from a workable system
and I think I need to jump in now to make it obvious what has to be done
before it's too late.
appologies to bruce in advance.
bin/stty. Define alias CCAR_OFLOW for MDMBUF.
Declare speeds as having type speed_t instead of long. speed_t is
long, which is wrong (POSIX specifies it to be unsigned integral),
but fixing it might introduce more serious bugs.
package: check installation, build package, create links,
touch cookie
repackage: ditto but don't check cookie
package-noinstall: just build package from installed stuff, no cookies
involved at all
package-links create the symbolic links only
delete-package: delete package and symbolic links
delete-package-links: delete links only
These should make the management of the spaghetti of package links
a little friendlier. :)
Add mbr and bteasy17 to tst01
read partitions from kernel instead of disk.
Still problems with writing labels, discussing with Bruce.
Extended slices doesn't get written yet.
user-level part has already been commited.)
Note that i've lost the "official" code for this; it went into the
system after 1.1.5.1. The commited code is my own version, but it has
proven to work for me for more than a year now.
o Make the framework generally more robust.
o Figured out how to nest the menu descriptions - no more grotty initialization
of menus.
o Fix bug with helpline and helpfile not being reset.
o Add stubs for the media selection code.
Coming next: Fdisk and disklabel screens using Phk's new libdisk stuff.
- If you take the wheel entry out of /etc/group and turn on NIS,
the '+:*::' line is incorrectly flagged as the entry for wheel (the
empty gid section is translated to 0), hence getgrgid() returns '+'
as the name of the group instead of 'wheel.'
- Using just '+:' as the 'turn on NIS' switch in /etc/group makes
getgrgid() dump core because of a null pointer dereference. (Last
time I was in here, I foolishly assumed that fixing the core dump
problems with getgrnam() and getgrent() would fix getgrgid() too.
Silly me.)
and `rtsflow' are the components of `crtscts'. `dtrflow' and `dsrflow' are
new and not yet supported. `dtrflow' may be useful for Cyclades serial
careds, which have h/w support for it and no h/w support for `rtsflow'.
print.c:
Report NTTYDISC in case the line is in this obsolescent state.
if an invalid ioctl is done on /dev/klog. logioctl() needs to return
an errno instead of -1 on a failed ioctl.
Submitted by: Mike Pritchard <[email protected]>
Made an All_FreeBSD() function.
Added a cmd-line interface (lowest rank) to the tst01 program.
The tst01 program is harmless (worst it can do is coredump), but it
is instructive to run, you can see what the slice-code things of your
disk...
This submission was done by hand-applying FreeBSD local modifications on
top of the UCB code, rather than trying to patch the UCB code in on top
of the FreeBSD code due to the extensive changes.
Reviewed by: pst (been handling 30k routes for 4+ months)
Obtained from: Sklower/Woody/Honing/Traina (8.4 UCB release)
Added another couple of menu item types.
Reshuffled the menus and added a few more. Sure wish I could figure out
how to initialize a menu with _one_ initializer rather than two! :(
It is the kernel driver's responsibility to do the list manipulation whenever
a selection timeout or a request sense occurs.
Print out the interrupt type that the device has been set to. It seems that
one of the Asus motherboards botches this and David thought a diagnostic would
be nice.
Fix a bug in my diagnostic code that David found.
Reviewed by: Wcarchive and David Greenman
the adapter's selections. Many fast periferals were getting upset when
the sequencer decided to rearbitrate after the device had already won
arbitration. This also forced the creation of a list threaded through
the SCBs (since we don't have enough space anywhere else) of commands that
are awaiting reselection. This list is run down before any new transactions
from the input queue are allowed. The list is appened to whenever we begin
a selection (simple case since the selecting device is always at the head)
and by the kernel driver whenever a request sense occurs. In the common
case, the list is only one element long, but when a reselection wins out
over a selection and that reselection generates a request sense, the
outstanding selection required for the retreval of the sense code grows
the list. On machines with many targets, this might cause the list to grow
large, so this solution, which will allow up to the maximum number of I/O
requests capible of the card elements in the list, was chosen. The list
manipulation is trivial and adds three sequencer instructions of overhead
to the selection phase.
This fixes the "target busy" errors from micropolis drives and the bursty
I/O problem when performing I/O between a Quantum Grand Prix and any other
device. I anticipate that this will correct many of the problems that
have been reported with this driver.
Reviewed by: Wcarchive and David Greenman
more to come in the next 24 hours, this is just the first stable result of
8 hours of hacking so far. The specification format for menus is pretty
much hammered out and the beginnings (very humble) of the doc hierarchy
are present for an example. It should be quite easy to add a lot more
menus quickly to this since I did go somewhat out of my way to make the
framework easy to work with. This is NOT the glorious semi-graphical
sysinstall (or whatever its name will be) that the install-geeks are working
on, this is simply the "son of sysinstall" I've been promising to write in
the interim for 2.0.5 and 2.1R (super install doesn't come until 2.2R).
>Number: 368
>Category: bin
>Synopsis: Lpd doesn't log errors after failed exec
>Description:
If an exec done by lpd fails, nothing is sent to the system log
indicating what went wrong. This is because lpd closes all of
the file descriptors before doing the exec, thus closing the syslog
file descriptor in the process.
[Fix applied]
Submitted by: [email protected]
- Moved to a more client-driven model. We aggressively attempt to keep
the default domain bound (as before) but we give up on non-default
domains if we lose contact with a server and fail to get a response
after one round of broadcasting. This helps drastically reduce the
amount of network bandwitdh that ypbind consumes: if a client references
the secondary domain at some later point, this will prod ypbind into
establishing a new binding anyway, so continuously broadcasting without
need is pointless.
Note that we still actively seek out a binding for our default domain
even if no client program has queried us yet. I'm not exactly sure if
this matches SunOS's behavior or not, but I decided to do it this way
since we can get into all sorts of trouble if our default domain comes
unbound. Even so, we're still much quieter than we used to be.
- Removed a bunch of no-longer pertinent comments and a couple of
chunks of #ifdef 0'ed code that no longer fit in to the new layout.
- Theo deRaadt must have become frustrated with the callback mechanism
in clnt_broadcast(), because he shamelessly stole the clnt_broadcast()
code right out of the RPC library and hacked it up to suit his needs.
(Comments and all! :)
I can understand why: clnt_broadcast() blocks while awaiting replies.
Changing this behavior requires surgery. However, you can work around
this: fork the broadcast into a child process and relay the results
back to the parent via a pipe. (Careful obervation has shown that the
SunOS ypbind forks children for broadcasting too, though I can only
guess what sort of interprocess communication it uses. pipe() seems to
do the job well enough.)
This may seem like the long way around, but it's not really that
hard to implement, and I'd prefer to use documented RPC library functions
wherever possible. We're careful to limit the number of simultaneous
broadcasters to avoid swamping the system (the current limit is 5).
Each clnt_broadcast() call only sends out a small number of packets
at increasing intervals. We're also careful not to spawn more than one
bradcaster for a given domain.
- Used clntudp_bufcreate() and clnt_call() to implement a ping()
function for directly querying a particular server so that we can
check if it's still alive. This lets me completely remove the old
bradcasting code and use actual RPC library calls instead, at the
cost of more than a few handfulls of torn-out hair. (Make no mistake
folks: I *HATE* RPC.) Currently, the ping interval is one minute.
- Fixed another potential 'nfds too big for select()' bug: use
_rpc_dtablesize() instead of getdtablesize().
- Quieted gcc -Wall a bit.
- Probably a bunch of other stuff that I've forgotten.
ypbind.8:
- Updated man page to reflect modifications.
ypwhich.c:
- Small mind-o fix from last time: decode error results from
ypbind correctly (*groan*)
yplib.c:
- same as above
- Change behavior of _yp_dobind() a little: if we get back a 'Domain
not bound' error for a given domain, retry a few times before giving
up and passing the error back to the caller. We have to sleep for a
few seconds between tries since the 'Domain not bound' error comes
back immediately (by repeatedly looping, we end up pounding on ypbind).
We retry at most 20 times at 5 second intervals. This gives us a full
minute to get a response. This seems to deviate a bit from SunOS
behavior -- it appears to wait forever -- but I don't like the idea
of perpetually hanging inside a library call.
Note that this should fix the problems some people have with bindings
not being established fast enough at boot time; sometimes amd is started
in /etc/rc after ypbind has run but before it gets a binding set up. The
automounter gets annoyed at this and tends to exit. By pausing ther YP
calls until a binding is ready, we avoid this situation.
- Another _yp_dobind() change: if we determine that our binding files
are unlocked or nonexistent, jump directly to code that pokes ypbind
into restablishing the binding. Again, if it fails, we'll time out
eventually and return.
>Number: 364
>Category: bin
>Synopsis: Interrupting man results in half-baked man page
>Description:
Interrupting man while it is waiting for the page to be formatted
results in a zero length file or a half-baked file.
>How-To-Repeat:
Inetrrupt man while it is formatting a page.
>Fix:
Pay more attention to the return value from the system command.
Submitted by: John Capo <[email protected]>
Also allow URL specification for a package. This works for things the
package may depend on, too.
Allow PKG_PATH to be used anywhere a package is being searched for.
go away whenever a clone's parent is changed, or a route is added in a
certain set of circumstances.
This also includes code to forbid setting a route's gateway to an
address which can only be reached through that route, thus (hopefully)
eliminating one class of cloning bottomless-recursion bugs.
components of the system.
The license is poorly worded, though I have an (email only) release
from the author for unlimited FreeBSD use. I will try to get something
more concrete, though the author's remote location makes this difficult.
Submitted by: Oleg Orel <[email protected]>
to be `int' or smaller and some functions returned `int' instead
of `void'. The first bug was detected when console functions were
defined in a place central enough for type checking to actually
work and the second bug was introduced when the interface was
changed to match what the console functions in other drivers actually
return.
too (otherwise the chain won't work).
(2) If NO_WRKDIR is set, "make clean" removes "./.*_done" (assuming
these are cookies...or should I list all the cookies?)
through the use of the config file flags as opposed to the option
"NSECS_MULTI". "NSECS_MULTI" has been removed from the driver.
The new capability allows boot-time modification of the config.
I made the changes I sent you before. In the interests of cleanliness, I made
modifications to /sys/i386/isa/tw.c to kill the warnings and make it compile
clean. While I was at it, I also made a bunch of internal functions static.
Submitted by: Gene Stark <[email protected]>
flags parameter to all xxstart routines so that the correct information can
be passed down into the device specific routines. This is needed to ensure
that ccb/scb allocation routines don't hang.
Submitted by: John Dyson
higher level scsi code.
Spls should never be conditionalized, so don't do so here.
Restructure the get_scb routine so that we can't get into an infinite
loop if the ccbs are exhausted and we are are called with SCSI_NOSLEEP set.
Other driver maintainer's that based their scb allocation routines on Julian's
code should look at these changes and implement them for their driver.
The aic7xxx driver inspired these changes because early revs of the
aic7770 chips have so few SCBs that you can actually run out. If you
have a rev C or aic7770 (as is reported by the driver probe) and had more
than 2 drives, you could get into an infinite loop when using up all of
the SCBs. Since the driver will only allow two SCBs per device and I
only had two devices, I never saw this problem on my Rev C card.
Bzero only 19 bytes of the scb instead of 2k (ack!). This was a hold
over from when a struct SCB only contained the information downloaded
to the board, but we now store kernel driver data in there as well. This
greatly lowers the overhead for small transactions (I get ~1MB/sec for
dds with a 512 byte block size).
Submitted by: John Dyson with the aic7xxx specific optimization by me
higher level scsi code.
Spls should never be conditionalized, so don't do so here.
Restructure the get_ccb routine so that we can't get into an infinite
loop if the ccbs are exhausted and we are are called with SCSI_NOSLEEP set.
Other driver maintainer's that based their ccb allocation routines on Julian's
code should look at these changes and implement them for their driver.
Submitted by: John Dyson
incomplete declarations here any more. Some things depend on
incomplete declarations elsewhere. The `offset' arg to d_mmap_t is
bogus (it is `int' but should be `vm_offset_t') but it is what the
driver mmap functions actually accept, although they are passed a
`vm_offset_t'.
Function declararions in headers should always be complete to avoid
warnings from `gcc -Wstrict-prototypes' for compiling modules that
don't even use the offending declarations.
don't expect this to work yet.. but at least they're here..
(hey this cvs stuff is fun!)
activate with a line exactly like the isa line in the config file,
(but specifying eisa :)
patches to come..
Headers should always use `__inline' for inline functions to avoid
syntax errors when modules that don't even use the offending functions
are compiled with `gcc -ansi'.
We now have RELEASE=CURRENT in the CVS-tree.
If this hasn't been edited, we will use "BUILT-yyyymmdd" where the time is
that of the compile, and leave it at that, we can't do any better.
If there is no serious objections, I will modify the "cvs co" script on
freefall to fiddle this file after checkout so that it becomes
CURRENT-yyyymmdd, where the time is that of the checkout.
1. Make paths work correctly.
2. Make pkg_add generally more robust in the face of failure.
3. Make the depend messages come out on stderr or stdout, but not both
interspersed! :-)
2. Fix a long-standing bug in pkg_add where the failure of one package in
a multipackage installation (pkg_add *.tgz) would blow you right out of
the water. Ick.
seperate exit values depending on the error. (The error values are
#defined and commented near the top of the file for clarity). This
is to help write a small bit of shell script for /etc/rc that calls
ypwhich a few times after ypbind is invoked to make sure we're
actually bound to a server before proceeding (if we aren't, the
automounter can fail if it's using NIS maps).
out by Bruce.
2. Add a "feature" to pkg_create (OK, OK, it's a miserable hack!) to get
it to dump its internal packing list out so that the `fake-pkg' rule in
bsd.port.mk can generate a more meaningful packing list.
ypbind.c: if a client program asks ypbind for the name of the server
for a particular domain, and there isn't a binding for that domain
available yet, ypbind needs to supply a status value along with its
failure message. Set yprespbody.ypbind_error before returning from
a ypbindproc_domain request.
yplib.c: properly handle the error status messages ypbind now has the
ability to send us. Add a ypbinderr_string() function to decode the
error values.
ypwhich.c: handle ypbind errors correctly: yperr_string() can't handle
ypbind_status messages -- use ypbinderr_string instead.
Change the interfaces of these functions to save space. The code
that takes the least amount of space is often the opposite to what
you might expect. E.g., it helps to waste a few bytes passing
pointers so that the compiler can't see that certain addresses
are identical (gcc likes to waste space by reloading fat constants
even when the constant is already in a register).
Rewrite getbootdev() to save 80 bytes of space and to make it less
ugly. 32 bytes were saved simply by omitting the continue statements
in the pseudo-switch.
recently introduced bloat in just 2 calls to biosread(), although
very little in calls to putc() and serial_putc(). Gcc produces
amazingly bad code for unnecessary conversions. E.g., if it has
`int x' in register %edx and wants to pass a char, then it could
simply push %edx and access only one byte in the callee. Instead,
it sometimes unnecessarily spills %edx; it always sign extends
%edx and pushes the result.
Remove useless `extern' in function prototypes.
Remove unused declaration of `end'.
Declare pbzero() and pcpy() like the library bzero and bcopy().
Declare printf() properly.
- it succeeded on non-directories (see POSIX 5.1.2.4).
- it hung on (non-open) named pipes.
- it leaked memory if the second malloc() failed.
- it didn't preserve errno across errors in close().
examination, I'm not entirely sure this was meant to be public. It's not
idempotent or anything. I'll make pkg_manage deal with it another way
until it's been confirmed one way or the other by Marc.
do fit, and beeping in case of an overflow.
. Drop a comment about the ``FORCE_COMCONSOLE'' option into
README.serial.
. Increase the name buffer for the root directory from 100 bytes
to 8 KB; this is in no way ideal, but (IMHO) the best that can
be done by now. People did encounter problems with their root
dir name listing overflowing the allocated buffer space. Once
we've got the three-stage boot, we should implement some basic
malloc(). Swap space is already getting tight now, perhaps the
swap should go into another 64 KB segment instead.
. Make the keyboard probe less paranoid. It should not give up in
case of a keyboard that's continuously demanding RESEND's. Even
though the keyboard reset apparently has not been reported to be
complete, it's at the very least proven that there IS something
like a keyboard available.
This solves problems with the ``Gateway-2000 AllKey programmable''
(sp?) keyboard, that experienced a total hang with the previous
probe.
Thanks goes to Scott Blachowicz <[email protected]> for his
extensive testing of my various interim (debugging) bootblocks
to get this working.
build, install) are now all skeletons and do nothing but
(1) Call pre-* target (if exists)
(2) Call scripts/pre-* script (if exists)
(3) Call do-* target
(4) Call post-* target (if exists)
(5) Call scripts/post-* script (if exists)
The do-* targets do all the work. The pre-* and post-* targets/scripts
don't exist by default. The main targets check for the cookies too, so
porters shouldn't have to worry about them at all.
NOTE: THE MAIN TARGETS IN THE PORTS MAKEFILES SHOULD GO AWAY. We need
to fix this before wcarchive comes back up. Change the names to do-*,
rip out the cookies, rip out the calls to pre-* etc. and most of them
should work.
Also, reorganize the whole thing so that similar targets are together
and add more comments. Surround section header with 64 #'s (C-u C-u
C-u # in emacs :).
Hopefully this will be the last major change to bsd.port.mk. Now let
the Makefile-hacking begin.
some (hopefully) less offensive stupidity:
If we detect that a user has loaded a module that fails to initialize
itself correctly, panic. There really isn't a safe way to recover from
something like this; we can't know that the module is bad until after
the entry point is called, by which time it's too late to do anything
about it.
now that we have the space.
If this works out to our liking, we will kill BOOTFLP.
Now, if only we could extract the kernel, incl symbols from a kzip'ed kernel...
can use the vn-driver instead of physical floppies, thanks guys !
Add the fixit-floppy back now that kzip made it fit again.
Don't make the gzip'ed *.flp files anymore.
rule.
2. Have all non-X11 prefix using packages include the BSD.local.dist mtree
file for initialization of /usr/local. I'm still not sure if this is
A Good Thing(tm) but I'll see what the users say. It's easily overridden.
3. Standardise on ${PKG_DBDIR} as pointer to /var/db/pkg or local preference.
- in mount_portal.c: included catching of SIGHUP to get portald to
re-read the config file.
- in mount_portal.c: in SIGCHLD handler the return values checked from
waitpid were wrong. Note. this routine was written correclty according
to the manual page for 4.4BSD, but waitpid does not exhibit this
behaviour. It is not returning 0 when WNOHANG is specified. I havent
checked this properly.
- in mount_portal.c: initialized the fdset for the select properly.
- in mount_portal.c: corrected poor casting in the select.
- in mount_portal.c: changed a break; to exit (0); so that the
children die after doing the hard work, this stops the select: bad
file descriptor messages.
- in pt_file.c: the kernel passes kernel style open flags to the
portal code which aren't compatible with "normal" O_ flags. I have
adjusted these in pt_file.c. In general I think the portal fs code
and portal_cred structure need changing to pass to the portald
the right style of flags _and_ the permissions.
- in pt_tcp.c: a few mistakes in typing of the socket structures,
getservbyname returns the port number as an int but sockaddr wants
the port number as an u_short.
- in pt_tcp.c: someone wrote this on a VAX/Sun whatever and forget
about byte ordering!! I've included a few htons about the place.
- in all the above I have sprinkled a few more debugging printf's.
Submitted by: "Duncan McL Barclay" <[email protected]
in a couple of cases, and it doesn't do much anyway. It used to save only
the newfs params (block/frag/cgroup.. and nothing more. Something that
don't belong in a disklabel in the first place.
- Add $Id$ string.
- Fix comment ("we might *not* be able to unload the
module afterwards without panicking...")
- Get rid of variable 'j' that I used in name checking
for(;;) loop and use 'i' instead (I thought there'd be
a problem with this, but there isn't).
got a 2.2 version DC21040 chip in my SMC ethernet card! He suggests bumping
the check all the way down to 2.0 since it's pre-2.0 we're actually guarding
against.
Submitted by: Matt Thomas <[email protected]>
"Building for WWW" (pops up in two different ports) "Installing for
web2c-6.1" (ditto), which aren even't reminiscent of the port's real
name.
Sorry jmz, please don't go fix the print Makefiles' own messages.
We are going to take them out after we do the great bsd.port.mk
update anyway.
if_tun_mod, etc...) from crashing the system. These modules are useful,
but because they don't yet have proper load()/unload() functions,
they can lead to panics: if, for example, you load the if_ppp module,
any user can panic the system by running modstat.
You can also hang the system outright if you try to unload the PPP
module too.
Changes are as follows:
- Save the name passed to us during the RESERVE stage for name matching
(we can't load if_ppp_mod twice: we've have two ppp0's and two ppp1's,
which is beyond strange). This makes the lkmexists() cheks somewhat
redundant, but there's no way around it that I can see.
- If we call the module entry point and find that we have no lkm_any
structure in our 'private' section, create a fake one. This keeps
modstat happy. We mark such modules as LM_UNKNOWN.
- Don't allow LM_UNLOAD modules to be unloaded: it just ain't
possible. (Unless someone wants to write a pppunattach() function. :( )
- In lkmunreserve(), mark private.lkm_any as NULL so we don't get
confused later. I think this is bogus, but I can't prove it.
XXX: the name matching used to keep the user from loading two
instances of the same module can easily be defeated simply by
changing the module name or, in the case of the oddball modules,
simply by renaming the module files. I haven't found a nice simple
way to tell one module from another.
covered now, and i've attempted to give textual representations
instead of magic numbers.
The st(4) driver still misses some pieces; i'm going to implement the
EOM functionality RSN.
Any takers for the MTCOMP command? Seems to have never been implemented.
the top level and have the build-package sequence of each port work
together.
For the old behavior (i.e, just go ahead and blindly pack everything up,
regardless of the contents of work/), there is a new target "repackage".
Since "build" depends on "configure", which depends on "patch", etc.,
this shouldn't disrupt any Makefile that doesn't break the dependency
chain.
The old behavior was very annoying because when I did a "make -k",
it would still try to go configure and build even if the extraction
failed.
The first problem I found was that descriptor 0 was being closed.
This happens because the modem variable is set to 0 to indicate
that it is not valid but there are not enough tests for the modem
variable being 0. You can see where I have done this in the patch.
Code in OpenModem() dups the modem descriptor if it is < 3. Once
this happened the modem was always open and an incomming call would
have getty and ppp reading the modem.
Descriptor 1 is closed when the quit command was executed from a
telnet connection. The next modem open returns descriptor 1
and this gets duped leaving the modem always open again.
The modem was not being closed when the connection dropped or was
closed from the other end. The UUCP lock was also not removed if
the modem could not be opened.
Reviewed by: Atsushi Murai <[email protected]>
Submitted by: John Capo <[email protected]>
interested parties.
Make the loader refuse to load anything below 1 MB -- we didn't
support it since FreeBSD 2.0R. Avoid gratuitously wiping out the BIOS
variables or the loader.
the kernel at 0-640k; we haven't had the ability to do that since before
2.0R. Furthermore, I fail to see how putting an instruction at 0 and then
doing a .org 0x500 is going to prevent the stuff from getting clobbered
in the first place; a.out is just too stupid to know about sparse address
spaces.
is necessary in order for panic+sync to work. Will also gloss over a panic
that Jordan was having with the install floppies that remains unexplainable.
2) Handle "bogus_page" a little better.
3) Set page protection to VM_PROT_NONE if the entire page has become !valid.
Submitted by: John Dyson (2&3), me (1).
1) Rewrote screwy code that uses an incore buffer without making it busy.
2) Use B_CACHE instead of B_DONE in cases where it is appropriate.
3) Minor code optimization.
This *might* fix kern/345 submitted by Heikki Suonsivu.
pages that are in FS buffers. This fixes the (believed to already have been
fixed) problem with msync() not doing it's job...in other words, the
stuff that Andrew has continuously been complaining about.
Submitted by: John Dyson, w/minor changes by me.
Previously they were only guarded by `#ifndef _ANSI_SOURCE'. They are
neither ANSI nor POSIX nor std and should never have been declared here.
Declare functions like abs() as having attribute `__pure2'. Declaring them
as having type `__pure' has been a no-op for some time.
Delete obsolete comment about stub locale functions.
Use consistent formatting for the rand48 functions. These and about 30
other functions should never have been declared here either.
one ypbind broadcast can yield several responses. This can lead to
some confusion: the syslog message from ypbind will indicate a rebinding
to the first server that responds, but we may subsequently change our
binding to another server when the other responses arrive. This results
in ypbind reporting 'server OK' to one address and ypwhich reporting a
binding to another.
The behavior of the rpc_received() function has been changed to prevent
this: subsequent responses received after a binding has already been
established are ignored. Rebinding gratuitously each time we get a
new response is silly anyway.
Also backed out the non-fix I made in my last ypbind commit. (Pass
me the extra large conical hat, please.)
(At some point I'm going to seriously re-work ypbind and the _yp_dobind()
library function to bring them in line with SunOS's documented behavior:
binding requests are supposed to be 'client-driven.' The _yp_dobind()
function should be responsible for retrying connections in response to
calls from client programs rather than having ypbind broadcasting
continously until a server responds. The current setup works okay in
normal operation, but we broadcast far too often than we should.)
- Don't write the label directly - use DIOCWDINFO.
- Avoid overflow in calculation of lseek() offsets.
- Fix format args in strings some more. %ld and %lu were often reversed and
#ifdefed out strings weren't fixed.
- Don't hard code the raw partition letter or DKBAD*.
- Write the qsort() comparision function in `C'.
- Fix all remaining warnings from `cc -Wall -Walmost-really-all'.
Add references to the ahc driver to the other adaptec man pages.
Remove the "NOTE" section of the ahb man page that complained about
Adaptec's NDA policy preventing 274x driver development.
is identical to the older version, just the copyright has changed. Many
thanks go to Dean Gehnert of the Linux camp who went the extra mile to make
this happen.
Other changes:
Update assembler man page to include the -v and -D options
Merge in Dean's latest changes to the assembler
Have the sequencer do a MSG_REJECT when the negotiated syncronous rate
is lower than the adapter supports. This forces asyncronous mode which
is faster at these rates anyway.
This code will be moved shortly to the non-gpld portion of the tree.
Previously, this worked right if both AUTO_EOI_1 and AUTO_EOI_2 are
defined, but not if AUTO_EOI_1 is defined and AUTO_EOI_2 is not defined.
The latter case should be the default. DUMMY_NOPS should be the default
too. Currently there are only two NOPs slowing down rtcin() (although
there are no delays in writertc()) and several FASTER_NOPs slowing down
interrupt handling in vector.s.
Fix stack offsets for the (previously) unused untested
FAST_INTR_HANDLER_USES_ES case.
through a temporary buffer instead of one character at a time. The old
method takes about 6 usec/char on a 486DX2/66. This is larger than than
the combined interrupt and PIO overhead for a 16550!
This change was first implemented in 1.1.5. It was rewritten for 2.1.
The clist access functions allow a simpler implementation at some cost
in correctness and speed. There needs to be an ungetc() function to
recover from EFAULT, and it wastes time to copy through a temporary
buffer.
Don't snoop on single characters that weren't read due to EFAULT.
Rewrite a snoop comment in my approximation to English.
Undo bogus exportation of ttnread().
OBUFSIZ should be increased to the same value as IBUFSIZE (both are
smaller than desirable because they have to fit on the stack), but
there are currently problems with magic buffer limits and watermarks.
Remove unused #define of TTMASK.
Undo bogus exportation of ttnread().
This should NOT go into 2.0.5 /phk
Support disk slices. This involves mainly replacing inline code with
function calls. Support for ST506 drives is temporarily broken since
the `setgeom' arg to dsopen() is not implemented completely enough to
use. The `setgeom' arg will go away and ST506 drives will be supported
in another way. A large amount of dead code is left in wdopen() as a
reminder of the problems here.
Close the device in wdsize(). Open tracking was broken on all drives
with a swap device.
Remove support for soft write protection. There are no ioctls to set
it. It was used to disable writing to unlabelled disks, but we want
to support writing to foreign partitions on unlabeled disks.
Use generic dkbad routines to do about 2/3 of the work for supporting
bad144.
Improve disk statistics: estimate 4MB/sec instead of 8MB/sec for
the transfer rate (ISA max is 4MB/sec, old IDE max is 3.3MB/sec);
fix dk_xfer[] (it counted sectors, not transfers); keep the estimate
dk_seek[] = dk_xfer[] (was sectors, is now transfers); only count
words actually transferred (the count is still too high after a
failed write and after retries). Remove wdxfer[].
Fix indentation in wdattach(). Fix resulting botched printing of the
disk size for ST506 drives. Print the disk geometry less cryptically.
o Fix the keyboard probe to properly wait for the ready bit before
sending a command to the keyboard controller. This should avoid the
problems some people are experiencing where the boot blocks hang the
system during keyboard probe. (It does solve it for me.)
o Fix a bug that effectively prevented the boot blocks from ever
passing control to the serial console. [while(--retries) instead of
while(retries--)]
o Gratuitously reduced the keyboard probe timeout from 500 to 5
seconds. :)
o Introduced a new option ``FORCE_COMCONSOLE'' as a commented-out
example in the Makefile, to force the usage of a serial console
regardless of a keyboard being connected or not.
o Moved all external declarations to boot.h, declared all functions
there, and ANSIfied all function declarations/definitions.
(printf() remains bogus, however -- i'm too lazy to fix this.)
We're in the ninetees, dunno why we should still support compilers
from the 70's.
of the plus or minus lists at all, reject him. This lets you create
a +@netgroup list of users that you want to admit and reject everybody
else. If you end your +@netgroup list with the wildcard line
(+:::::::::) then you'll have a +@netgroup list that remaps the
specified people but leaves people not in any netgroup unaffected.
and #if defined (I586_CPU) thingies into identifycpu() so that we only
compile in what's actually needed for a given CPU. So far as I can tell,
none of my 386 machines generate a cpu_vendor code, so I made the extra vendor
and feature line conditional on I486_CPU and I586_CPU. (Otherwise we
print out a blank line which looks silly.)
at least one user out there who's system won't autoboot from the
serial console because of what sounds like 'phantom keystrokes'
making the timeout timer trip. I've tried to solve this by
adding an extra call to init_serial() right before the 'Boot:'
prompt is printed (done only if RB_SERIAL is set) to hopefully
make sure that the input buffer is clear. Unfortunately, the fellow
is in Germany and I haven't heard back from him yet. I haven't
been able to duplicate this problem on my hardware, so this is
a stab in the dark. At the very least, it shouldn't hurt anything.
kernels with 'options I586_CPU.'
The declaration for pentium_mhz is hidden inside an #ifdef I586_CPU,
but machdep.c refers to it whether I586_CPU is defined or not. This
temporary hack puts the offending code inside an #ifdef I586_CPU as
well so that a kernel without it will successfully compile.
I must emphasize the word 'temporary:' somebody needs to seriously
beat on the identifycpu() function with an #ifdef stick so that
I386_CPU, I486_CPU and I586_CPU will do the right things.
Dropping into the debugger when a break comes down the serial line is a
>MISFEATURE (1st class)< and has been put under it's own #ifdef. This
should be a magic sequence of chars instead.
For those where it was easy, drivers were also fixed to call
dev_attach() during probe rather than attach (in keeping with the
new design articulated in a mail message five months ago). For
a few that were really easy, correct state tracking was added as well.
The `fd' driver was fixed to correctly fill in the description.
The CPU identify code was fixed to attach a `cpu' device. The code
was also massively reordered to fill in cpu_model with somethingremotely
resembling what identifycpu() prints out. A few bytes saved by using
%b to format the features list rather than lots of ifs.
like "3DBorder" and "[". (NB, the "3DBorder" problem has actually
been intention, it allowed for weird section names like "3xyzzy". We
don't have them, either.)
(Partially) Submitted by: [email protected] (Brian Tao)
link stage fell over for any program that attempted to use rexec().
Ruserpass() remains undocumented; i could not find any documentation
for it on other systems.
Also added a BUGS section to the man page, stating that this function
constitutes a potential security hole (as well as the underlying
"exec" service).
Submitted by: rgrimes
Originally submitted by: [email protected] (Alistair G. Crooks)
Obtained from: [email protected]
Fix PR 303: msdosfs: moving a file into another directory causes panic.
" ... the code that does the rename already has the denode
locked when msdosfs_hashins() gets called, resulting in the panic
when the routine attempts to lock the denode again.
...
The attached patch changes the msdosfs_hashins() routine to not lock the
denode. The caller is now resposible for obtaining the lock instead
of having msdosfs_hashins() do it for them."
don't lock the vnode - it doesn't appear to ever be necessary for VCHR
vnode/inodes. This fixes a bug introduced in the previous commit that
caused tty timestamps to act strange (causing 'w' and 'finger' to show
the tty wasn't idle when it may have been for hours).
Have netstart directly source sysconfig so that it stands on its own.
Do not source netstart in rc, run it with sh.
Rework the dangerous /etc/hostname.* so that it uses a variable with
a list of interfaces and a variable for each interface in that list.
The files /etc/hostname.* become obsolete with this change, the
information is now stored in /etc/sysconfig.
Source any /etc/start_if.${ifn} files so they can export things to
netstart (plans for future enhancements in this area.)
Obsolete /etc/defaultrouter, this is now down with $defaultrouter from
sysconfig.
o add missing man pages
o make all man pages clearly refer to the libcompat thingie
o add the information to the vtimes(3) and vlimit(3) man pages
that nobody has reimplemented the functions by now
o add the missing getpw.c
o add code and man pages for cftime(3) and
ascftime(3) -- i found them somewhere in old
unfinished work
in the mrouted. inet_parse returns network byte ordered address, but there
are a couple comaprisons that need to be done on the addresses and the
comparisons are done in host order. I left the comparisions for 0xffffffff
alone, because this value is the same in network and host orders.
Submitted by: Mark Tinguely <[email protected]>
file specifications when they've been extracted (enabling you to get a file
fast if it occurs somewhere close to the front).
Submitted by: Marc van Kempen <[email protected]>
> * the gdb-4.13 of current (compiled and used under 2.0R) can not attach to my
> own processes (it works only then i'm root - else i get open failed - for my
> own processes)
how embarassing ! This turns out to be a bug in infptrace.c. Below
is a patch. Could some kind soul apply it ?
Submitted by: "Gary J." <[email protected]>
where one or more of the non-default domains are not yet bound.
If we make a YP request for a domain other than the default domain,
and there is no binding for the new domain yet, _yp_dobind() sees
that the /var/yp/binding/DOMAIN.VERS file for the unbound domain is
not locked (by ypbind) and from this it concludes that the NIS system
is dead, so it gives up.
This behavior has been changed: before giving up in this case, we now
make a second check to see if the binding file for the *default* domain
is also not locked. Only if the default domain binding file is also
unlocked to we now assume that ypbind has bought the farm and bail out.
(Note: this assumes that the user hasn't changed the default domain
while ypbind is running.)
With this change, _do_ypbind() is allowed to proceed into the next
section of code wherein it prods ypbind into establishing a binding
for the new domain. This first call times out after ten seconds,
after which it should retry and succeed. From then on, the binding
for the second domain should be handled normally.
new driver code, there are diffs to several other existing files
on the system and a man page.
This version of matcd implements the rest of the key ioctls related to
playing audio CDs and reading table of contents information from any
type of disc.
This update also corrects several problems detected since the original
version 1(10) was released. These include:
1. Jordons report on the kernel -c string problem.
2. A problem with the driver being confused by other types of
devices located at addresses it probes.
3. An old CD TOC wouldn't always be cleared after a disc change.
4. Cleaned up code so -Wall yields no warnings on 2.0 and later.
5. A problem with drive getting out of sync with the driver when
changing between CD-Data and CD-DA.
There have only been two reports from the field relating to problems
so either the first release isn't really being used or doesn't have
many problems.
If there are any problems with this submission, please let me know.
Submitted by: Frank Durda IV <uhclem%[email protected]>
1. pkg_create now has a -P argument for specifying dependencies on the
command line.
2. pkg_add will honor dependencies and chain-load them automatically if
it finds the required package(s) in the same directory as the package
that is being loaded. For best results, install packages from a directory
containing all the packages you'll possibly need
(like /usr/ports/packages/all).
2 remaining flaws:
1. pkg_add looks in one place (where you were when you loaded the primary
pkg) for depended packages. If you can come up with a search path scheme
that's not a total hack - be my guest!
2. Recursive dependency expansion can result in the name of a dep being
listed more than once. This doesn't bother pkg_add since it checks
for package existance with pkg_info and will skip already-loaded packages.
I don't know how/if pkg_delete handles this yet, however. I need to look
into it.
all .tgz files go to /usr/ports/packages/.packages, and a relative
symlink is created for every item in CATEGORIES...i.e., if "CATEGORIES
= foo bar", then /usr/ports/packages/{foo,bar}/pkgname.tgz both point
to /usr/ports/packages/.packages/pkgname.tgz.
Suggested by: jkh
bits) along, and rmt did the wrong thing in calling open(2) with random
garbage as third parameter. Make it create new files with 0666
(modified by the umask of the remote shell anyway).
This removed the last show-stopper from tar not working with remote
archives.
Also please note that previous commit regarding UH24F controller was
misattributed to Poul - it was Steve's!
Submitted by: Steve Gerakines <[email protected]>
1.5 seconds in ftintr_wait().
Three people have reported that this fixes the problem they are having.
Submitted by: Steve Gerakines <[email protected]>
Fixed remaining known bugs in the buffer IO and VM system.
vfs_bio.c:
Fixed some race conditions and locking bugs. Improved performance
by removing some (now) unnecessary code and fixing some broken
logic.
Fixed process accounting of # of FS outputs.
Properly handle NFS interrupts (B_EINTR).
(various)
Replaced calls to clrbuf() with calls to an optimized routine
called vfs_bio_clrbuf().
(various FS sync)
Sync out modified vnode_pager backed pages.
ffs_vnops.c:
Do two passes: Sync out file data first, then indirect blocks.
vm_fault.c:
Fixed deadly embrace caused by acquiring locks in the wrong order.
vnode_pager.c:
Changed to use buffer I/O system for writing out modified pages. This
should fix the problem with the modification date previous not getting
updated. Also dramatically simplifies the code. Note that this is
going to change in the future and be implemented via VOP_PUTPAGES().
vm_object.c:
Fixed a pile of bugs related to cleaning (vnode) objects. The performance
of vm_object_page_clean() is terrible when dealing with huge objects,
but this will change when we implement a binary tree to keep the object
pages sorted.
vm_pageout.c:
Fixed broken clustering of pageouts. Fixed race conditions and other
lockup style bugs in the scanning of pages. Improved performance.
Fixed remaining known bugs in the buffer IO and VM system.
vfs_bio.c:
Fixed some race conditions and locking bugs. Improved performance
by removing some (now) unnecessary code and fixing some broken
logic.
Fixed process accounting of # of FS outputs.
Properly handle NFS interrupts (B_EINTR).
(various)
Replaced calls to clrbuf() with calls to an optimized routine
call vfs_bio_clrbuf().
(various FS sync)
Sync out modified vnode_pager backed pages.
ffs_vnops.c:
Do two passes: Sync out file data first, then indirect blocks.
vm_fault.c:
Fixed deadly embrace caused by acquiring locks in the wrong order.
vnode_pager.c:
Changed to use buffer I/O system for writing out modified pages. This
should fix the problem with the modification date previous not getting
updated. Also dramatically simplifies the code. Note that this is
going to change in the future and be implemented via VOP_PUTPAGES().
vm_object.c:
Fixed a pile of bugs related to cleaning (vnode) objects. The performance
of vm_object_page_clean() is terrible when dealing with huge objects,
but this will change when we implement a binary tree to keep the object
pages sorted.
vm_pageout.c:
Fixed broken clustering of pageouts. Fixed race conditions and other
lockup style bugs in the scanning of pages. Improved performance.
drivers to protect DDB from being invoked while the console is in
process-controlled (i.e., graphics) mode.
Implement the logic to use this hook from within pcvt. (I'm sure
Søren will do the syscons part RSN).
I've still got one occasion where the system stalled, but my attempts
to trigger the situation artificially resulted int the expected
behaviour. It's hard to track bugs without the console and DDB
available. :-/
warnings and are cosmetic only. Poul once requested them, but neither
Sean nor Søren commented on them, so i commit it now before it's
getting lost some day.
card. This is the braindamaged card with the 80186 CPU on it. It is
slow, probably not very good after all, but hey, if you have one lying
around doing nothing anyway...
Added the "zp0" driver to GENERIC.
Second part of update to fdlibm 5.2: speed up argument reduction for trig
functions in the case pi/4 < |x| < 3pi/4.
Remove unused static constants ("one").
isctype.c:
o The tolower() and toupper() functions duplicated too much code
and were out of date (surprise). This didn't matter because
it was difficult to call them.
o Change formatting to be more like that in <ctype.h> (with
extra parentheses as in the macros). Perhaps this file should
be machine generated or everything should be handled like
__tolower() so that no code is repeated.
nomacros.c:
o Instead of looking at _USE_CTYPE_INLINE_ to see what <ctype.h>
has done, set _EXTERNALIZE_CTYPE_INLINES_ to tell <ctype.h>
what to do, so that we don't have anything left to do. Note
that code is now generated even if inlines are used by default.
This allows users to switch to non-inline versions.
Fix numerous ANSI conformance bugs and other nits.
ctype.h:
o There were no prototypes behind the macros (conformance bug).
o isascii() didn't have enough parentheses (plain bug).
o tolower() and toupper were always static inline (conformance
bug? You could undef them and take their address, but this
gave different addresses in different modules. You couldn't
undef them and declare them (correctly) again). <stdio.h>'s
treatment of putc() shows one way to handle this problem,
but it only works because the putc() macro is allowed to
reevaluate its args. I used a hack controlled by
_EXTERNALIZE_CTYPE_INLINES_ to get <ctype.h> to generate the
code (the previous hack involving _ANSI_LIBRARY_ goes away).
This has the advantage that the core of the functions is only
written down once and the disadvantage that another layer of
functions is required. The extra layer goes away if inline
functions are used, leaving only the problem of understanding
why there are functions named toupper(), __toupper and
___toupper() as well as a macro named toupper.
o Nothing seems to define _USE_CTYPE_LIBRARY_. Eliminate it
o Let the user set _USE_CTYPE_INLINE_ and _DONT_USE_CTYPE_INLINE_
for full control over inlining.
o The args for the inline functions didn't have enough
underscores (conformance bug).
o The formatting and ordering was inconsistent (style bug).
o TODO: fix conformance bugs brought by including <runetype.h>.
of the linker to enforce linking of modules in command line order it is
not possible to link gdb shared with -lcompat.
*HACK ALERT*
Removed -lcompat from LDADD and bring in the necessary functions out of
libcompat as a source module until the linker can be fixed.
underlying bugs which are caused by mixing static/shared libraries with
this change in place.
The shlib code is not capable of supporting this feature in it's present
state and will need significant modifications in order to do so.
properly. I know, tcsh is not a "Real Shell".
jc p2 :0.0 Tue04PM - -u (tcsh)
^^^
7173 p2 S+ 0:01.33 -u (tcsh)
^^^
Submitted by: John Capo <[email protected]>
If a goto findpcb occurred during the processing of a segment, the TCP and
IP headers were dropped twice from the mbuf which resulted in data acked
by TCP but not delivered to the user.
Reviewed by: davidg
handles default settings and has a prototype translation file for people
wishing to add extra languages (please!).
Submitted by: Wolfram Schneider <[email protected]>
register ourselves as an NIS version 1 UDP server to pacify older SunOS 4
ypbinds that seem to insist on having one around. All this does is allow
ypserv to respond to DOMAIN_NONACK requests that are periodically
transmitted by ypbind: the server will not actually work as an NIS v1
server in any other way.
Unlike the mainline code, which implements this as a compile-time
option, this feature can be turned on with the newly-added -k flag
at runtime.
Bunped version number to 0.13. (What the hell.)
Updated the man page to reflect this change, also made a couple of small
edits to reflect the recent changes in the /etc/rc* setup.
select() returns EINVAL if you try to feed it a value of FD_SETSIZE greater
that 256. You can apparently adjust this by specifying a larger value of
FD_SETSIZE when configuring your kernel. However, if you set the maximum
number of open file descriptors per process to some value greater than
the FD_SETSIZE value that select() expects, many selects() within the RPC
library code will be botched because _rpc_dtablesize() will return
invalid numbers. This is to say that it will return the upper descriptor
table size limit which can be much higher than 256. Unless select() is
prepared to expect this 'unusually' high value, it will fail. (A good
example of this can be seen with NIS enabled: if you type 'unlimit' at
the shell prompt and then run any command that does NIS calls, you'll
be bombarded with errors from clnttcp_create().)
A temporary fix for this is to clamp the value returned by _rpc_dtablesize()
at FD_SETSIZE (as defined in <sys/types.h> (256)). I suppose the Right
Thing would be to provide some mechanism for select() to dynamically
adjust itself to handle FD_SETSIZE values larger than 256, but it's a
bit late in the game for that. Hopefully 256 file descriptors will be enough
to keep RPC happy for now.
add #includes for YP headers when compiling with -DYP to avoid some implicit
declarations.
getgrent.c & getnetgrent.c: add some #includes to avoid implicit declarations
of YP functions.
Added a new type to uiomove - "UIO_NOCOPY" which causes it to update
pointers and counts, but doesn't do any data copying. This is needed
for upcoming changes to the way that the vnode pager does its page
outs.
Added a new hash init function call "phashinit" that allocates and
initializes a prime number sized hash table.
vfs_cache.c:
Changed hashing algorithm to use the remainder of dividing by a prime
number to improve the distribution characteristcs. Uses new phashinit
function in kern_subr.c.
will cause kernel compiles to work even if the src/includes directory
doesn't exist but still do the 'Right Thing' and pull files from the
source tree if it does exist.
Reviewed by: Bruce Evans
Obtained from: Casper H. Dik (by vay of Usenet)
Small patch to help improve NIS rebinding times (among other things):
>From: [email protected] (Casper H.S. Dik)
>Newsgroups: comp.sys.sun.misc,comp.sys.sun.admin
>Subject: FIX for slow rebinding of NIS.
>Summary: a small change in libc makes life with NIS a lot easier.
>Message-ID: <[email protected]>
>Date: 17 Jan 92 17:39:05 GMT
>Sender: [email protected]
>Organization: FWI, University of Amsterdam
>Lines: 138
>Nntp-Posting-Host: halo.fwi.uva.nl
Have you been plagued by long waits when your NIS server is rebooted?
READ ON!
Sun has a patch, but the README says:
********************* WARNING ******************************
This is a new version of ypbind that never uses the NIS
binding file to cache the servers binding. This will have
the effect of fixing the current symptom. However, it might
degrade the overall performance of the system when the
server is available. This is most likely to happen on an
overloaded server, which will cause the network to produce
a broadcast storm.
*************************************************************
Therefor, I have produced another fix.
o What goes wrong.
When the NIS server is rebooted, ypserv will obtain different ports
to listen for RPC requests. All clients will continue to use the old
binding they obtained earlier. The NIS server will send ICMP dst unreachable
messages for the RPC requests that arrive at the old port. These ICMPs
are dropped on the floor and the client code will continue sending the
requests until the timer has expired. The small fix at the end of this
message will pick up these ICMP messages and deliver them to the RPC layer.
o Before and after.
I've tested this on some machines and this is the result:
(kill and restart ypserv on the server)
original% time ypmatch user passwd
user:....
0.040u 0.090s 2:35.64 0.0% 0+126k 0+0io 0pf+0w (155 seconds elapsed time)
fixedhost% time ypmatch user passwd
user:....
0.050u 0.050s 0:10.20 0.9% 0+136k 0+0io 0pf+0w (10 seconds elapsed time)
Rebinding is almost instantaneous.
o Other benefits.
RPC calls that use UDP as transport will no longer time out but
will abort much sooner. (E.g., the remote host is unreachable or
111/udp is filtered by an intermediate router)
ypxfr can't easily be reduced down to one file like yppush because it
needs to do certain special things (such as binding to a specific
machine (the NIS master)) which the yp_*() functions in libc don't
allow.
to open the mounted block device containing the directory to put the bad
sector files in, and opening of mounted block devices hasn't been allowed
since Net/2 or before. Attempt to open the raw device instead. Be more
careful about long names.
Use lstat() instead of stat() to search for block devices so that my
symlink to the default floppy doesn't cause problems.
Check for truncation of the block number when it is squeezed through the
mknod() interface. The maximum used to be only 32767, but now it large
enough.
#179). The fix implements a ttyhalfclose() (sort of), resetting the
session and pgrp pointers when the physical device is about to be
closed.
Suggested by: bde
old type (stty) ioctls can easily bypass locking bits.
It involves manual conversion from old ioctls to new ones,
large piece of code duplicated from tty_compat.c
ypbind is supposed to create it but it doesn't. This is because when
it checks the return value for the attempted open() of
/var/yp/binding/DOMAIN.VERSION, it tests only for a value of -1. This
is bogus because open() doesn't return -1 in this case. Now it checks
for < 0 instead.
This should make life easier for many NIS-newbies who would otherwise
be left scratching their heads wondering why the NIS client stuff won't
work despite their best efforts. ("I set the domain name on my machine,
and /var/yp exists, but when I start ypbind and try a 'ypcat passwd,'
it says it can't bind to a server for this domain! Please help!")
*long, heavy sigh*
declaration for ether_ntohost(). (Does anyone know what header file
is supposed to contain the declarations for the ether_addr functions?
I can't them in the SunOS includes anywhere.)
in libc, we can get rid of the private/special copies of yp_*.c
files and rpcgen them at compile time instead. This leaves us with
just one unique source files: yppush.c
so that these ioctls can be handled by the calling layer(s).
Clean up the recently added code:
- include the appropriate header to declare an implicitly declared function.
- declare timeout functions correctly and remove numerous bogus casts that
hid (but didn't fix) their incorrectness.
after ttioctl too, because it can change t_line.
Remove (TS_CNTTB | TS_LNCH) test, it is always inherits from
old tty mode and can't be reach in currently setted mode.
o the includes are now properly done by <sys/foo.h> instead of "foo.h"
o a bunch of undeclared functions has been resolved
o pcvt finally supports devconfig
When attempting to abort a command, don't assume that just because the
sequecer happens to have SCBPTR pointing at the scb we want that it is
an active command.
old value.
Remove unnecessary check for active messages in setup SCB. This same test
would also jump to p_mesgin_done which would "ACK" an extra time possibly
confusing the target.
Tell the kernel driver whenever we send an ABORT_TAG message.
In rare cases, when the filter specified accesses an multi-byte value that
is split across mbuf's, the value loaded is incorrect. And if you are very
unlucky (like me) it will index off the end of the mbuf and into an
unallocated page and panic the system.
If you look at the code you will discover the the index *k* is added to
the pointer *cp* and the used AGAIN as a subscript.
1. Nuke out the aculib files that crept in somehow by mistake.
2. Fix the ${.CURDIR} path so that this stuff actually compiles.
It actually compiled for me before the commit, but I must have had
something short-cutting the bug.
to poll succesfully even if we are sharing the interrupt.
Register the interrupt handler before the attach.
This commit makes the 294x PCI shared interrupt compliant. This has
been tested with an aic7870 motherboard controller and a 294x in the
same machine shareing an irq.
- Report valid residual byte counts. We actually pause the sequencer
when the residual is non-zero. I thought about using DMA to do this,
bus sequencer program space is tight.
- Fix embarassing off by one error in the computation of a 2's
compliment variable. This was most likely the cause of the
many problems reported with the tagged queuing code.
- Handle "MAX_SYNC" as a special case (ie we are the ones starting
the sync negotiation sequence). This was done so that the target
scratch area can be initialed to 0 offset (asyncronous transfers)
safely. The initialization to 0 (was 15) is necessary since in
some cases a Wide negotiation could run into problems if SCSIRATE
was set wrong and we went into data(in/out).
- Trim the DMA routines a little by using some procedures. Net
effect is more functionality with 3 less instructions after this
update.
- Toggle the WIDEODD bit of the DFCNTRL whenever this is not the
last SG block. It has no effect in the 8bit bus configuration,
but in the Wide configuration ensures that the overlap byte is
held in the SCSI block if the transfer is odd so it will end
up in the next SG (the correct behavior).
- catch the interrupt type (EDGE/LEVEL) before chip reset instead
of guessing the right type.
- Add pause variable to the ahc struct to better handle the different
interrupt types and pausing the sequencer.
- CLRINTSTAT -> CLRSCSIINT: This is a documented bit in the CLRINT
register in newer Adaptec documentation, so use their name for it.
- Report valid residual byte counts.
- Don't mess with the target scratch areas > id 8 on single, narrow,
channel devices. The BIOS does a checksum of this area and can
flip out if we zero it out.
- Initialize the sequencer FLAGS scratch ram variable in the single
channel devices to 0. This was the cause of the annoying warning
where we would get a cmdcmplt the first time we did any type of
transfer negotiation with no valid scb. It also fixes the problem
that looked like the INTSTAT register wasn't clearing fast enough.
This only showed up on 294x cards, not motherboard aic7870s.
- Add the AHC_AIC7870 type and use it as the superset of aic7870
based controllers.
- clear the sync offset section of the targ scratch area so that
we default to asyncronous transfers. This was only a problem
for wide controllers because there was a scenario where the
offset wouldn't get updated before a data(out/in) phase would
occur. This required some change in the sequencer code since we
were depending on this field to hold the rate to negotiate.
- allow sync and wide negotiated commands to be tagged (the sequencer
now handles this properly).
date: 1995/02/04 20:27:23; author: phk; state: Exp; lines: +1 -1
added *.info and *.db to the default "ignore" list in cvs to avoid obviously
common mistakes.
job af warning me about mail as my work version does. This patch will
will fix this for bash(1) if MAILPATH is exported:
Submitted by: Mark Murray <[email protected]>
I'm not exactly sure why all the inb/outw stuff got added to netboot.h
and I'd be happy if someone like Martin or Bruce could take a look at it!
Submitted by: "Serge A. Babkin" <[email protected]>
* to reduce the number of adapter failures. Transceiver select
* logic changed to use value from EEPROM. Autoconfiguration
* features added.
Submitted by: "Serge A. Babkin" <[email protected]>
Etherlink III 'zp' on 2.0R, but it did not work with the -current.
Noriyuki Takahashi <[email protected]> san has fixed this bug.
Our alpha-testers are tested this driver with 3C589B-COMBO and
3C589B-TP. And it works fine.
I also fixed a little about the use of ZP_DEBUG symbol and beautified
the awful Frankenstein-style indent :-) with "indent -c0 -nfc1 -i4".
[Also merge with Bruce's last changes]
Submitted by: "HOSOKAWA Tatsumi" <[email protected]>
that ypxfr is supposed to log messages to /var/yp/ypxfr.log if it exists,
using syslog() makes more sense, especially since ypserv does the same
thing already. Try to use stderr by default, and use syslog() if stderr
is not a tty.
Also update the man page to reflect this change.
It is common case when modem hangs with carier on but don't
receive anything from another side.
This thing commonly healed with hangup and redialing.
Enhancements below allows to determine when such action
is needed and inform attach program with SIGURG signal.
There two ioctls set: outfill and keepalive, used from both
sides of connection. Outfill repeatedly sends FRAME_END with
specified timeout (i.e. 40 seconds). It is needed to get input on
other side even if no user activity on slip line currently.
Keepalive checks FRAME_ENDs from other side, and if no one
got in specified timeout (i.e. 60 seconds, max modem retrain time),
send SIGURG to attach program.
I plan to add code to slattach to handle this thing too.
Reviewed by: wollman
restore but really didn't do it.
Restore message from old rc about configuring syscons whith
echo added before it to go to new line after "echo -n xtend" f.e.
and similar stuff.
changes to it based upon other outstanding bug reports and commits made
after his work.
Comments:
(a) sysconfig is still used to do all configuration. I was not going to
change that out from under you.... a user never need edit netstart
or rc* unless they're being very weird.
(b) rc.maint has been folded back into rc. It is just unworkable as
a separate chunk because of ordering bogosities
(c) netstart does what it says... it starts up enough of the network to
get up, it doesn't start every bloody daemon that might talk to a
socket... netstart ifconfig's the devices and sets up routing if
configured to do so.
(d) nfs disks are mounted immediately after netstart completes
(e) syslog is started as early as possible (right after nfs) so that error
messages can get logged to remote syslog servers properly
(f) named is started (there is an argument that says that named should be
started before syslogd because if you are the dns server for your domain,
you'd like named to resolve remote hosts in syslog.conf, but this is
a minority case and the trivial workarround is to put the syslog host
in /etc/hosts or use an /etc/resolv.conf -- why? because you want syslog
to catch named errors, which is a MUCH more important and likely occurance)
(g) NOW all of the rest of the network daemons such as the time stuff, RPC,
NIS, NFS, Kerberos and inetd are started
(h) the rest of the generic stuff is done (cron/printer/sendmail)
(i) shared libraries are set
(j) /etc/rc.i386 is run (this does FreeBSD/386 specific stuff like ibcs2,
xtend, and all of the syscons stuff
(this is actually started as /etc/rc.`uname -m`
(k) the syscons stuff has gotten a serious cleaning to make it consistent
with rc conventions
(l) rc.local has had the comments about syscons removed (they are not relevant
to this file now) and the full name of the kernel has been restored to
/etc/motd
Submitted by: pts
NIS maps (get rid of extraneous slash a la /var/yp//domainname).
Have ypxfr log all output to /var/yp/ypxfr.log if stdin is not a
tty. This should allow logging to be done when ypxfr is called from
inside ypserv in response to a yppush request.
Update man page to reflect the change (and fix a typo).
update what has actually been touched. This should speed up
screen access on slow hardware.
Introduced setting of "destructive" cursor size, much like
the old hardware cursor.
on a "NQNFS" kernel config option. NQNFS is a 4.4 wart and the performance
penalty of the lease checks on the client/server for _local_ I/O is too high
to have this occur all the time - especially when most people will never
use it.
date: 1995/03/26 18:18:59; author: wpaul; state: Exp; lines: +23 -17
Make syslogd work again: in needs to be started in netstart right
before the rest of the system daemons are brought up and *after* the
network interfaces have been configured.
Also fix one other potential problem: the NIS services need to be started
relavively early since some of the other daemons might need them. The
automounter is a good example: if you use amd with NIS-based maps, you'd
better have NIS running before you start it. :) I think mountd might
need it too, now that netgroups can be read via NIS as well.
date: 1995/03/23 01:25:18; author: jkh; state: Exp;
Another pass through our rc files in an attempt to eliminate historical
crufy and generally make all of this easier to understand and modify.
I got irritated with not seeing the interrupt numbers in a (crowded)
"systat -vmstat" display, so I fixed it. Here is a patch to please be
applied in src/usr.bin/systat
Install the biosboot as /usr/mdec/boot[12]
Make the traditional links from [swf]dboot and boot[swf]d to boot[12] files.
Install dosboot as /usr/mdec/boot/fbsdboot.exe
*Really* strip out unused local symbols from shared objects.
This was a typo on my part caused by an assumption that the profiled
libraries stripped symbols that same way as the non-profiled libraries.
Cut-n-Paste strikes again.
Obtained from: NetBSD
1) Preserve old buffer contents when input buffer overflows.
Old code clear buffer and rewrite it again, if !MAXBEL
(for MAXBEL it does right thing :-).
F.e. if you type too long string, last chars passed,
not first ones as expected.
Moreover, it flush output queue too in this case without any needs.
2) Don't do IXOFF, if IGNCR and c==\r, ignore completely.
3) If PARMRK is active and !ISTRIP and char == 0377
put yet one 0377 to distinguish it from parity mark sequence.
POSIX standard (thanx Bruce).
Reviewed by:
Submitted by:
Obtained from:
CVS:
if (tp->t_line != 0)
test when CS_ODONE, it fails for NTTYDISC, use
if (linesw[tp->t_line].l_start != ttstart)
instead.
Reviewed by:
Submitted by:
Obtained from:
CVS:
BREAK/parity/framing errors.
Term "correctly" assumes POSIX spec. and 4.4 ttyinput() behaviour.
1) Discard BREAK/parity at interrupt level when apropriate IGN*
is set in iflag. It helps "raw" mode works even IGN* is set.
2) Zero parity (if INPCK) and framing directly in buffer
before passing it to b_to_q() in "raw" mode.
Efficency:
interrupt level: if no error occurse, only two "test" commands added
"raw" mode: buf scan incc times for parity/framing added
Reviewed by:
Submitted by:
Obtained from:
CVS:
Grrr. If the dbhash routines weren't grossly overengineered I wouldn't
even need to do this! :-(
Also now export the hash_stats routine. Manpage coming RSN - I promise.
New variables:
PATCH_SITES: patch equivalent of MASTER_SITES, overridable with
. MASTER_SITE_OVERRIDE.
PATCHFILES: Additional files to fetch and give to patch before
. applying the ones in patches/patch-*. If name ends
. with ".gz" or ".Z", it will be piped through zcat first.
Plus PATCH_DIST_STRIP and PATCH_DIST_ARGS that serve the same functions
as PATCH_STRIP and PATCH_ARGS for patches in patches/patch-*.
In the documentation and echo messages, I used the term "distributed
patches" and "FreeBSD patches" to refer to ${PATCHFILES} and patches/patch-*.
If you can come up with better names, by all means go ahead and fix them.
"grep PATCH /usr/ports/*/*/Makefile" reveals seven ports (mule, jless,
jtcl, jtk, dgd, less, color_xterm, gee I wonder why I'm the one who
implemented this) that can benefit from this. I'm now diving headlong
into /usr/ports to fix their Makefiles.
installation script, DEINSTALL for the deinstallation script, and
REQ for the requirement script, will be added with appropriate
flags to PKG_ARGS if they exist under pkg/.
you to push the same host into its NFS export lists twice, but mountd
tries to do it anyway. This means that putting:
/some_file_system -ro host1 host1
in your /etc/exports file causes an error. This is bogus: mountd should be
smart enough to ignore the second instance of host1. This can be a problem
in some configurations that use netgroups. For example, each host in my
netgroups database is has two entries:
startide (startide,-,) (startide.ctr.columbia.edu,-,)
When mountd sees this, it tries to put startide.ctr.columbia.edu into the
export list *twice*. Just listing 'startide' /etc/exports list will also
screw up because mountd will try to resolve the netgroup 'startide' instead
of the hostname 'startide.'
My solution is watch for duplicate entries in get_host() and mark them
as grouptype GT_IGNORE, which do_mount() will now cheefully throw away.
This is a bit of a kludge, but it was the least obtrusive fix I could
come up with.
Also silenced a compiler warning: arguments passwd to xdr_long() should
be u_long, not int. :)
merged cache changes, and figure it out based on the B_VMIO buffer flag.
Fixes a problem where delayed write VMIO buffers would sometimes get
recopied into kernel-alloced memory.
Submitted by: John Dyson
use it. :-)
It now explicitly requires the specification of a directory to import
from, either as an argument to the script, or by asking the user about
it. (Previously, it implicitly used `.', like cvs import does.)
Also implemented an option `-n', which does essentially the same like
the overall CVS option `-n': show only what would have been done,
don't do any commitment. Note that since the modules' database is
checked out in place (and not commited back), it will erroneously be
reported as to be imported, too:
cvs import: Importing /home/ncvs/ports/foobar/foo/modules
I ports/foobar/foo/modules/CVS
N ports/foobar/foo/modules/modules
This is an unwanted side-effect, but gives the user the option to see
if the `ed' magic did the right thing when editing modules/modules.
Rod, can you please check the function ``checktag'' in the script if it
will be restritctive enough?
Report floppy/tape units on seperate lines as fdX:/ftX: to correct lots of
ways the current scheme failed to end the output with \n.
Add controller and/or drive designator to the fron of several messages
that come from this drive. [It's not fun to track down driver messages
using grep over the source tree.]
Reviewed by: joerg
before the rest of the system daemons are brought up and *after* the
network interfaces have been configured.
Also fix one other potential problem: the NIS services need to be started
relavively early since some of the other daemons might need them. The
automounter is a good example: if you use amd with NIS-based maps, you'd
better have NIS running before you start it. :) I think mountd might
need it too, now that netgroups can be read via NIS as well.
Forms now have their own local bindings table so that anything
declared within a form is local to that form. This means you can
have fields of the same name in different forms.
Added inlined attribute setting for strings e.g. "This is \bold bold"
Added entry and exit functions for fields.
1) Eliminate spaces and double ':'.
2) Remove duplicated capabilities from tc= expansion.
It is needed to not overflow historycal 1024 limit.
Add range check and return -1 if entry is too big instead
of corrupting user memory.
include <pci/pcivar.h> without including <sys/devconf.h> and other
drivers include <pci/pcivar.h> before including <sys/devconf.h> if
certain identifiers are defined.
The devconf headers have convoluted interdependencies. <sys/devconf.h>
includes <machine/devconf.h> which includes <pci/pcivar.h>. Most
drivers include <sys/devconf.h> so even isa drivers depend on
<pci/pcivar.h>. For similar reasons, most drivers depend on another
pci header, on an isa header and on two scsi headers.
opposed to 0644 or 0755). It's finally still masked by the process'
umask(2), and it does not make sense to restrict it further than that.
This (especially for mkdir(2)) was causing major headaches for the CVS
tree, since a member of group cvs was later not able to get cvs
checkout permission for the mirrored tree failed to write the lock file).
interpret it. I've preserved the bugs that perl must be installed
to build part of perl and that it must be installed in the wrong place
(no ${DESTDIR}).
- ignore the partition table if it is identical with the bogus one in
/usr/src/sys/i386/boot/biosboot/start.S. Honoring the bogus size
field was fatal. The error is detected but other compatibilty
cruft weakens the error handling too much for this case.
- weaken the partition entry checking to allow the following treatments
of C/H/S addresses when C should be >= 1024:
(1) allow C = 1023, H = max, S = max.
(2) allow C to be correct modulo 1024.
Other compatibilty cruft weakens the error handling to allow all
C/H/S addresses, but there too many errors were reported.
Improve error messages:
- print C/H/S addresses if relevant.
- distinguish primary partition table from extended partition tables.
- don't use diskerr() except for i/o errors.
to accurately track this. It isn't an indicator of resource consumption
anyway.
Removed cnt.v_kernel_pages: We don't implement this and doing so accurately
would be very difficult (and ambiguous - since process pages are often
double mapped in the kernel and the process address spaces).
Make sure all arguments to the yp_*() functions are valid before sending
them off to the server. This is somewhat distressing: once again my
FreeBSD box brought down my entire network because of NIS bogosities.
I *think* the poor argument checking in this module is the cause, but
I still haven't been able to reproduce the exact series of events that
lead to the ypserv crashes. For now I've resorted to sticking my FreeBSD
box in a seprate domain. Hopefully a weekend of heavy testing will
uncover the problem.
NOT derived from the Linux code and is thus not GPL'd. It is the author's
express wish that the GPL copyrighted version be removed and this BSD copyright
version take its place. Considering our own stance on this, I'm certainly
not going to argue! [Note to NetBSD folks: You're free to grab it now :-)]
Submitted by: Mikael Hybsch <[email protected]>
Change strtok() to strsep(), cause memory corruption for all
programs which use strtok() too in the same time.
Fix potential NULL reference, depends of /etc/hosts.conf format
Fix the bug when service name fetched always from beginning of the line,
not from parsed token.
programs which use strtok() too in the same time.
Fix potential NULL reference, depends of /etc/hosts.conf format
Fix the bug when service name fetched always from beginning of the line,
not from parsed token.
remapping mechanism in the following manner: if given an entry +@foo
and there is no netgroup named 'foo,' try searching for a regular
user group called 'foo' and build the cache using the members of
group 'foo' instead. If both a netgroup 'foo' and a user group 'foo'
exist, the 'foo' netgroup takes precedence, since we're primarily
interested in netgroup matching anyway.
This allows access control schemes based on ordinary user groups
(which are also available via NIS) rather than netgroups, since
netgroups on some systems are limited in really brain-damaged ways.
Note: if you put +::0:0:::::: in /etc/master.passwd as your only NIS
entry, it will cause all NIS uids and gids to be remapped to zero. This
is *intentional*. That's the way it's supposed to work. Enabling NIS with
no remapping at all is done with +:::::::::, not +::0:0::::::. Similarly,
+:::::::::/bin/csh will remap the shells of all NIS users to /bin/csh.
Or, you could do +wpaul:::::::::/bin/csh to remap NIS user wpaul's shell
to /bin/csh but leave everyone else alone.
ypserv to do a yp_match() with an a null or empty key causes much havok.
(Note that this could be construed as a denial of service attack if used
maliciously.)
my network because setnetgrent() was trying to do a lookup on group "".
It seems that an attempt to do a yp_match() (and possible yp_next())
on a null or empty key causes Sun's ypserv in SunOS 4.1.3 to exit
suddenly (and without warning). Our ypserv behaves badly in this
situation too, thoush it doesn't appear to crash. In any event, getpwent,
getnetgrent and yp_match() and yp_next() are now extra careful not to
accidentally pass on null or empty arguments.
Also made a small change to getpwent.c to allow +::::::::: wildcarding,
which I had disabled previously.
in.c: when an interface address is deleted, keep its multicast membership
. records (attached to a struct multi_kludge) for attachment to the
. next address on the same interface. Also, in_multi structures now
. gain a reference to the ifaddr so that they won't point off into
. freed memory if an interface goes away and doesn't come back before
. the last socket reference drops. This is analogous to how it is
. done for routes, and seems to make the most sense.
- Have the +@netgroup/-@netgroup caches handle the +user/-user cases too.
- Clean up getpwent() to take advantage of the improved +user/-user handling.
function calls. Broken tracking of open partitions gets fixed as a side
effect. Races in sdopen() and sdioctl() become more numerous than before.
Close the device in sdsize(). Media removal could not have worked right
when unused swap devices were held open. There may now be a problem
with used swap devices not being held open.
Fix ancient operator precedence bug in sddump(). It may have been
possible to attempt dumping to unloaded media.
Remove NetBSD ifdefs. We're too different now, and the NetBSD driver was
already too different for them to be relevant.
Remove support for soft write protection. There are no ioctls to set it,
and this driver never set it either. It was used in the wd driver to
disable writing to unlabelled disk, but we want to support writing to
foreign partitions on unlabeled disks.
Clean up some formatting and restore some old-style function headers.
happen normally when there is heavy write activity to a file since the
vnode isn't locked (NFS plays fast and loose with vnode locks). This change
"fixes" PR#267.
ultra14f.c and eliminate constants.
Correct EISA slot scan loops to look at slots 1 to 15 inclusive (off
by 1 errors all over the place). Other drivers need this, I will get
to it after a little more work.
Correct the ultrastore EISA probe so that it starts after the last
EISA slot probed instead of starting over from slot 0.
We need an eisa.h to move a lot of common constants into. I will
write it if someone tells me where it should go (sys/eisa?).
#include <i386/isa/isa.h>
return IO_EISASIZE instead of hard coded 0x1000.
if_ep.c:
Remove commented out disabling of interrupts that gave a
"comment withing a comment" warning.
for +@netgroup/-@netgroup entries. This saves the getpwent functions
from having to do all the work.
- Fix potential bug: when pwd_mkdb writes the YP-enabled flag to the secure
password database, it uses the wrong database descriptor. (It uses the
descriptor from the non-secure database, which is already closed by the time
things are being written into the secure dastabase).
password databases:
#define _PW_KEYPLUSBYNUM '5' /* special +@netgroup entries */
#define _PW_KEYMINUSBYNUM '6' /* special -@netgroup entries */
#define _PW_KEYPLUSCNT '7' /* number of +@netgroup entries */
#define _PW_KEYMINUSCNT '8' /* number of -@netgroup entries */
This is to help getpwent.c in libc build the +@netgroup/-@netgroup
caches.
members over shared library members. This modification causes the linker
to use the first definition it sees for a symbol instead of having
priorities based on the library type. This modification should allow
gdb to compile again.
Obtained from:
Email conversation with Paul Kranenbury, but implemented completely by
me. If it doesn't work, it's my fault not his.
VTEXT not always getting cleared when it is supposed to. Added check to
make sure that vm_object_remove() isn't called with a NULL pager or for
a pager for an OBJ_INTERNAL object (neither of which will be on the hash
list). Clear OBJ_CANPERSIST if we decide to terminate it because of no
resident pages.
Fixed the I/O statistics
Allow WD1007 type controllers to work
Support MULTI-BLOCK I/O
Correct delay to use port 0x84, reading the status register
might not be a long enough delay.
Changed probe message to match SCSI type devices.
was the wrong size. This is the likely cause of panics reported by
Lars Fredriksen and Paul Richards related to a -1 blkno when paging
via the swap_pager.
Submitted by: John Dyson
1) Supports PCI to PCI bridge devices (and tries to initialise them,
even if the BIOS is brain dead).
2) Supports shared PCI interrupts. Interrupt handlers now MUST return
'0' if they found nothing to do, '1' otherwise.
New features tested with i486 systems based on the Intel Saturn and
a DEC 4channel Ethernet card only, but expected to work on most systems.
The option PCI_REMAP has been removed !
Submitted by: Wolfgang Stanglmeier <[email protected]>
It's time to start moving in the directions we've had in mind for awhile.
SGML for everything new and old stuff moved into a location where it can slowly
be aged and removed (basically, Text/).
Delete bogus localhost.rev.
Add prototype localhost.rev and a script to create it automatically.
(NB to installl people: you should ask ``do you have a full-time connection
o the Internet?'', run this script, and enable named if the answer is
yes.)
1. Move all system configuration variables into /etc/sysconfig
2. Adapt other files to use it.
3. Add a host of new variables for micro-managing your system in various
ways. For 2.1, /etc/sysconfig will be machine-edited so that the user
doesn't even have to care at all about the various funny names we picked.
4. Enable dset. We won't get it debugged if we never use it, and no one
has said anything negative about it yet, so here goes!
5. Try to use one consistent style throughout.
sd.c: Julian's removal of subdriver requests
st.c, scsi_tape.h: Julian's suport of compressed tape drives
Note: compressed tape drives are still not working fully.
scsiconf.h, scsi_base.c, scsi_driver.c: address problems in probes
and error console logs
to the user address space unless pcb_onfault is set. The code is currently
commented out because iBCS2 and process debugging parts of the kernel
need to be changed/fixed first.
Submitted by: Sebastian Strollo <[email protected]>
- In /usr/src/lib/libc/yp/yplib.c, function yp_first when clnt_call
fails with (r != RPC_SUCCESS) ysd->dom_vers should be set to 0! This
ensures that /var/yp/bindings/dom.vers will be read again on retry.
What happens now is that when our server is down and someone tries to
use yp they will continue to try until kingdom come. So:
if(r != RPC_SUCCESS) {
clnt_perror(ysd->dom_client, "yp_first: clnt_call");
ysd->dom_vers = -1;
^^^^ change to 0
goto again;
}
fix Dennis Fortin's problem for good, if I've got it figured out right.
(The problem was that a `struct ifaddr' could get deleted out from under
the current requester, thus leaving him with an invalid interface pointer
and causing even more bogus accesses.)
Remove private mkdir command for /usr/include/g++, this is now
handled by mtree.
Make the whole file fit in 80 column output, sort the SRCS list and
split into .c and .cc sources.
Use $Id$ instead of $FreeBSD$ since we pulled support for this.
Add DPADD to match LDADD and now include <bsd.prog.mk> to define
the DPADD values (This is a hack until the .mk stuff can be corrected
so that ${LIB*} is visiable in bsd.lib.mk.)
Optimize beforeinstall target by eliminating a subshell.
that everyone else does: you can now use +host/-host, +user,-user and
+@netgroup/-@netgroup in /etc/hosts.equiv, /.rhosts, /etc/hosts.lpd and
~/.rhosts. Previously, __ivaliduser would only do host/user matches,
which was lame. This affects all the r-commands, lpd, and any other
program/service that uses ruserok().
An example of the usefullness of this feature would be a hosts.equiv
file that looks like this:
+@equiv-hosts
Since the netgroup database can now be accessed via NIS, this lets you
set up client machines once and then never have to worry about them
again: all hosts.equiv changes can now be done through NIS. Once I
finish with getpwent.c, we'll be able to do similar wacky things
with login authentication too. (Our password field substitution
will finally be on par with everyone else's, and I'll finally be
able to fully integrate my FreeBSD machine into my network without
having to worry about the grad students sneaking into it when I'm
not looking. :)
Danger Will Robinson! I tested this thing every which way I could, but
Murphy's Law applies! If anybody spots a potential security problem with
the way my matching algorithm works, tell me immediately! I don't want
crackers snickering and calling me names behind my back. :)
work because parse_netgrp() doesn't recurse properly. Fixed by
changing
if (parse_netgrp(spos))
return(1);
to
if (parse_netgrp(spos))
continue;
inside parse_netgrp(). (Lucky for me I happen to have a fairly complex
'live' netgroup database to test this stuff with.)
as tn3270 can replace _putchar(0 with their own routine and still keep
using the __cputchar() routine used by all of the other curses routines.
Reviewed by: "Andrey A. Chernov, Black Mage" <[email protected]>
>Description:
ctm(1) sometimes did not free up all used resources (open pipes and
processes, heap memory). This happened whenever one of the passes
ended prematurely, and it became very apparent when running it on
a bunch of already applied deltas, resulting in a ``gunzip: resource
temporarily unavailable'' due to the maxproc # exhausted.
in all other places here.
This is a hack, the interface should be changed to use off_t's
everywhere around, but this will require to update all the programs
that happen to use libkvm.
/usr/src/bin. Note that some patches are still needed in that directory.
I (Joerg) finished most of Philippe's cleanup. /bin/sh will still
need *allot* of work, however.
Submitted by: [email protected] (Philippe Charnier)
routines (and merged local changes). The changed vnode_pager_uncache
gets rids of the bogosity that you can call the routine without
having the vnode locked. The changed vnode_pager_umount properly locks
the vnode before calling vnode_pager_uncache.
It was previously after the VOP_RENAME and the reference and lock on
the vnode had already been lost, allowing interesting internel
inconsistencies. This is one of the two reasons why freefall was crashing
every hour or two (the other being nullfs bugs).
Don't call vnode_pager_uncache in revoke(). revoke() is only allowed on
VCHR and VBLK vnodes.
- Added support for reading netgroups from NIS/YP in addition to the
local /etc/netgroups file. (Note that SunOS and many other systems only
support reading netgroups via NIS, which is a bit odd.)
- Fix Evil Null Pointer Dereferences From Hell (tm) that caused
parse_netgrp() to SEGV when expanding netgroups that include
references to other netgroups. Funny how nobody else noticed this.
This is the first step in implimenting +@netgroup substitution in
getpwent.c and any other places that could use it and don't already
support it (which is probably everywhere).
during the FS sync. The system would appear to hang momentarily
if there was a large backlog of I/O. This is because the vnode
remains locked during the output - preventing normal character
I/O. The problem was exacerbated by the FFS contiguous block
allocation fixes and a semi-broken disksort(). The inode/date
will still be synced during a normal FS dismount and whenever
the inode is changed for other reasons.
libskey contains references to _crypt and can't resolve it unless
-lcrypt occurs after it in the link command. This only occurs when
linking statically.
libskey contains references to _crypt and can't resolve it unless
-lcrypt occurs after it in the link command. This only occurs when
linking statically.
Change the library order so libcrypt is the last library in the list.
libskey contains references to _crypt and can't resolve it unless
-lcrypt occurs after it in the link command. This only occurs when
linking statically.
libskey contains references to _crypt and can't resolve it unless
-lcrypt occurs after it in the link command. This only occurs when
linking statically.
by heading off possible null pointer dereferences in grscan(). Also
change getgrnam() slightly to properly handle the change: if grscan()
returns an rval of 1 and leaves a '+' in the gr_name field and YP is
enabled, poll the YP group.byname map before giving up. This should
insure that we make every effort to find a match in the local and
YP group databases before bailing out.
probe of the device and shouldn't affect normal operation. It seems that
some version of the aic7870 are extreamly slow in clearing their interrupt
register so the added delay is required to ensure we don't poll a stale
interrupt value.
Clean up debugging printfs and stuff superflous output into #ifdef AHC_DEBUG.
Ensure that sdtrpending and wdtrpending are cleared in all cases after
we recieve an SDTR or WDTR message.
With this commit, the 294x should work or at least be much closer to
working properly.
default switches, template functions get EXTERNAL linkage in each file
in which they occur, causing multiple definition errors during
linking. The enclosed patch (from gnu.g++.bug) appears to solve the
problem (I enclose the accompanying message as well).
This patch fixes the multiply defined template functions bug
which was introduced in 2.6.1.
Submitted by: "Justin T. Gibbs" <[email protected]>
Obtained from: Jason Merrill at cygnus support on G++ mailing list
a device specific shutdown routine for devconf. Assign the value of this
to the kern_devconf struct. Implement a device shutdown routine for if_de
that disables the device. This will stop the device from corrupting memory
after a reboot.
VFCF_NETWORK (this FS goes over the net)
VFCF_READONLY (read-write mounts do not make any sense)
VFCF_SYNTHETIC (data in this FS is not real)
VFCF_LOOPBACK (this FS aliases something else)
cd9660 is readonly; nullfs, umapfs, and union are loopback; NFS is netowkr;
procfs, kernfs, and fdesc are synthetic.
- Do ntp right
- Move recenrly-added and long-standing junk from rc.local into rc, so
. that rc.local truly is LOCAL.
- Fix named invocation to use the correct boot file location.
submitting them as context diffs for the following files:
sys/netinet/ip_mroute.c
sys/netinet/ip_var.h
sys/netinet/raw_ip.c
usr.sbin/mrouted/igmp.c
usr.sbin/mrouted/prune.c
The routine rip_ip_input in raw_ip.c is suggested by Mark Tinguely
([email protected]). I have been running mrouted with these patches
for over a week and nothing has seemed seriously wrong. It is being run in
two places on our network as a tunnel on one and a subnet querier on the
other. The only problem I have run into is that mrouted on the tunnel must
start up last or the pruning isn't done correctly and multicast packets
flood your subnets.
Submitted by: Soochon Radee <[email protected]>
one is much more intelligent, not only that it would accept multiple
man page locations, it also behaves like ``make'' in that it will only
deal with cat pages that are out of date (by default).
Wolfram also wrote a man page for it.
Submitted by: [email protected] (Wolfram Schneider)
declares them to return char *. For some reason, this causes no problems
with the old compiler tools, but doing a 'make world' with gcc 2.6.3 in a
seperate DESTDIR got me this error:
yacc -d /usr/src/usr.bin/compile_et/error_table.y
cc -O2 -I. -I/usr/src/usr.bin/compile_et/../../lib/libcom_err -I/mnt/usr/include -c y.tab.c -o error_table.o
In file included from /usr/src/usr.bin/compile_et/et_lex.lex.l:11,
from /usr/src/usr.bin/compile_et/error_table.y:233:
/mnt/usr/include/stdlib.h💯 conflicting types for `malloc'
/usr/src/usr.bin/compile_et/error_table.y:80: previous declaration of `malloc'
/mnt/usr/include/stdlib.h:104: conflicting types for `realloc'
/usr/src/usr.bin/compile_et/error_table.y:80: previous declaration of `realloc'
*** Error code 1
Stop.
Declaring malloc and realloc to return void * fixes this. It could be that
the new gcc is a bit more picky about these things.
now returns NULL and sets a global 'mb_map_full' when the map is full.
m_clalloc() has further been taught to expect this and do the right thing.
This should fix the "mb_map full" panics that several people have reported.
when I'm not sure whether or not that directory exists."
Today I discovered that rebuilding /usr/include completely from scratch
doesn't work, because the libss Makefile tries to install headers into
/usr/include/ss, which 'make includes' does not create. The result is that
the libss Makefile plants the header files in /usr/include as individual
files called 'ss,' with the second one overwriting the first, and the
third one overwriting the second. So instead of a directory called
/usr/include/ss, you end up with just one file called /usr/include/ss with
only the last header file in it. Check out /usr/include/ss on freefall
and you'll see what I mean.
I've modified the beforeinstall target in the libss Makefile to check
for the presence of the ${DESTDIR}/usr/include/lbss directory and to
create it if it isn't already there. Hopefully I did it right.
with individual devices for each type of sound card:
opl, sb, sbxvi, sbmidi, pas, mpu, gus, gusxvi, gusmax, mss, uart
EXCLUDE_* options are no longer required to be included in the config file.
They are automatically determined by local.h depending on the devices
included.
Move #includes in local.h to os.h so files are included in the proper
order to avoid warnings.
soundcard.c now has additional code to reflect the device driver
routines needed.
Define new EXCLUDE_SB16MIDI for use in sb16_midi.c and dev_table.h.
#ifndef EXCLUDE_SEQUENCER or EXCLUDE_AUDIO have been added to
soundcard.c and sound_switch.c where appropriate.
Probe outputs changed to reflect new device names.
Readme.freebsd not needed. Update sound.doc with new config instructions.
Reviewed by: wollman
list? (It should be added at the bottom to the sites serving export-
restricted code, please)
Country Site and Maintainer
======= ========================================================
Brazil ftp://ftp.iqm.unicamp.br/pub/FreeBSD
Pedro A M Vazquez <[email protected]>
Reviewed by: roberto
Submitted by: Mark Murray <[email protected]>
in the man page. ifconfig -au affects all interfaces marked as up,
and ifconfig -ad affects only the interfaces marked down. ifconfig -a
still handles everything. This change is purely for compatibility with
SunOS, for those who might be accustomed to the SunOS ifconfig's
behavior.
established. This way, automatic scripts are possible that might
control the SLIP connection. It's unacceptable for a daemon that's
being controlled by a variety of signals to not leave its PID
somewhere. The file name contains the terminal path name component of
the associated tty device, so it should be unique even with multiple
parallel slattach's running. The file will be unlinked at regular exit.
Also found a minor bug in the option handling by compiling with -Wall.
commit by bde.
Fix bugs in floating point formatting. The 4.4lite version is similar
to revision 1.3 in old-cvs and is missing all of jtc's fixes in revision
1.4 in old-cvs. Revision 1.2 in ncvs fixed one of the old bugs but
introduced at least one new one (for %.0e).
old-cvs log:
revision 1.4
date: 1993/11/04 19:38:22; author: jtc; state: Exp; lines: +33 -20
My work from NetBSD to make printf() & friends ANSI C compliant.
Fixes several bugs in floating point formatting:
1. Trailing zeros were being stripped with %e format.
2. %g/%G formats incorrect.
3. Lots of other nits.
and M_IPFW for firewall chans memory on the same opportunity,
theese types of memory are unique enough to have own identifiers and
besides vmstat looks much more useful and right for those now
- Don't define NO_IMPLICIT_EXTERN_C here. It is already the default
(defined in i386/bsd.h).
- Don't lose the fixed comment about FUNCTION_PROFILER.
- Don't lose the define of NO_PROFILE_DATA.
Replace the unused define of COMMENT_BEGIN by the less-unused define
of ASM_COMMENT_START. COMMENT_BEGIN was only defined in i386-specific
files and was not used in any part of gcc-2.6.3. ASM_COMMENT_START
is defined for several targets and is used for stuff that we don't
support (dwarf).
stuff. I'd like to have it in CVS, and i figured that this might be
the best place to go.
Someone (phk?) could install it into /usr/local/bin on freefall, for
convenience.
Suggested by: phk
2.Implment Redail function as working correctly.
3.Clean up a code as I notice.
4.Now, RTT getting close to 50ms with ISDN/TA 38400bps !!
Reviewed by: [email protected]
Submitted by: [email protected]
Fixed the MAKEDEV pattern for SCSI processor type driver so it doesn't
screw up ptys. Does anyone want to suggest a better name than "pt0" for
SCSI processor devices before 2.1?
allow Q_SYNC regardless of "target" uid, we allow it with -1;
fix bug that caused all ops to refer to user quotas, not group.
Submitted by: Mike Karels
To use this: recompile src/gnu/usr.bin/cc, compile your kernel. The
files you want to profile should be compiled with '-a -g'. "strip -x"
the kernel and run. You don't need to profile all files in the kernel.
My next commit is the program to extract the data from the running kernel.
basic-block profiling:
1. use a .stabs(25) symbol to link all the data structures together with.
The regular method isn't safe for the kernel.
2. add a BB before the prologue and add a BB after the epilogue, this
alows us to find the length of any counted BB. This is a cheap and somewhat
reasonable measure of actual cost.
1. We always keep one 16th of the vnodes on the freelist, so that the
namecache doesn't get trashed. It used to be that it wasn't a problem, but
the only vnodes getting released these days are directories and things which
Clean up and improve the namecache.
1. We always keep one 16th of the vnodes on the freelist, so that the
namecache doesn't get trashed. It used to be that it wasn't a problem, but
the only vnodes getting released these days are directories and things which
gets forced out of the VM/cache. The latter is not numerous enough to keep
the pool of vnodes needed for the namecache sufficiently big.
2. Purge invalid entries in the namecache as soon as we notice them. This
avoids a stale entry pushing out a valid entry on the LRU list.
3. Speed up the lookup in the namecache by avoid a special case branch.
4. Make the cache purge routines do the thing they're supposed to, and in
a decently efficient manner.
5. Make the size of the namecache follow the number of vnodes, so that we
can always point to all the vnodes we have in core.
6. Readability has gone way up.
7. Added a "options NCH_STATISTICS" feature that will gather more
detailed statistics on the performance of the namecache.
Reviewed by: davidg
1. We always keep one 16th of the vnodes on the freelist, so that the
namecache doesn't get trashed. It used to be that it wasn't a problem, but
the only vnodes getting released these days are directories and things which
Clean up and improve the namecache.
1. We always keep one 16th of the vnodes on the freelist, so that the
namecache doesn't get trashed. It used to be that it wasn't a problem, but
the only vnodes getting released these days are directories and things which
gets forced out of the VM/cache. The latter is not numerous enough to keep
the pool of vnodes needed for the namecache sufficiently big.
2. Purge invalid entries in the namecache as soon as we notice them. This
avoids a stale entry pushing out a valid entry on the LRU list.
3. Speed up the lookup in the namecache by avoid a special case branch.
4. Make the cache purge routines do the thing they're supposed to, and in
a decently efficient manner.
5. Make the size of the namecache follow the number of vnodes, so that we
can always point to all the vnodes we have in core.
6. Readability has gone way up.
7. Added a "options NCH_STATISTICS" feature that will gather more
detailed statistics on the performance of the namecache.
Reviewed by: davidg
(cvs is dumping core on me :-( )
1. We always keep one 16th of the vnodes on the freelist, so that the
namecache doesn't get trashed. It used to be that it wasn't a problem, but
the only vnodes getting released these days are directories and things which
gets forced out of the VM/cache. The latter is not numerous enough to keep
the pool of vnodes needed for the namecache sufficiently big.
2. Purge invalid entries in the namecache as soon as we notice them. This
avoids a stale entry pushing out a valid entry on the LRU list.
3. Speed up the lookup in the namecache by avoid a special case branch.
4. Make the cache purge routines do the thing they're supposed to, and in
a decently efficient manner.
5. Make the size of the namecache follow the number of vnodes, so that we
can always point to all the vnodes we have in core.
6. Readability has gone way up.
7. Added a "options NCH_STATISTICS" feature that will gather more
detailed statistics on the performance of the namecache.
Reviewed by: davidg
if a signal is received.
This fixes a bug where killing the process would cause a
"No manual entry for XXX" to be printed even if the manpage
was found.
o less restrictive, you can choise uid, gid ...
o invite user into some groups
o encrypted passwords with crypt
o batch mode (for instance, this works now:
$ adduser -batch jkh guest,uuadmin "Jordan K. Hubbard" passwd
see manpage for more details)
Submitted by: Wolfram Schneider <[email protected]>
object has fallen off the end of the cached list - this is likely the
last reference to the vnode and it should be reused before non file
vnodes that are already on the free list (VDIR mostly).
the copy built from here was overwritten by the other copy and the other
copy was put in library-building command lines twice. ld now objects to
duplicated modules.
Fix it so that calls to extend_get won't dereference 0 when "swap
on sd.." calls sdsize() on systems with no SCSI devices.
This probably really fixes Poul's "boot with no SCSI" problem.
first place and we were too long in finding out. Now we know, and the
damage is hard to fix. This is part one: ld will not link gcc dynamic,
if specified as "-lgcc".
Suggested by: dyson & davidg
both define ttydefchars[] as globals. This was fixed in 1.1.5
by making ttydefchars[] static like it should always have been.
Submitted by: Bruce Evans <[email protected]>
$Id$ information, and other code to make sound driver compile and work
correctly with FreeBSD.
Integrate changes obtained from Sujal Patel. These changes are:
o local.h: reverse option logic from EXCLUDE_* to AUDIO_*
o pas2_mixer.c: small addition
o ad1848.c: minor change with macro names
o sequencer.c: minor change with note check
o many spelling corrections in comments in about every other file
- Implement ether_hostton()
- Implement ether_aton()
- Modify ether_aton() and ether_ntoa() to match the semantics of the
SunOS versions of these functions.
- Neaten up ether_hostton() and ether_ntohost() a little.
- Get rid of ether_print() since it isn't needed for rarpd and it isn't
documented as a standard ethers(5) function.
rarpd.8:
- Make it clear that the 'ipaddr' that rarpd looks for in /tftpboot
is actually in hexadecimal (as in /tftpboot/803B4032) since those who
are not versed in the black art of system administration are not likely
to know this.
disables dysfunctional disinformed namei's,
needlessly negating namei cache."
These hacks cuts the number futile attempts made by cc and ccp to find
cross-compilers and other weird stuff. A make of the BOOTFLP kernel
has 20% less namei calls now, that is from 30647 down to 24563 calls.
of queuing mails only can be restored by uncommenting a CFLAGS+= line
in the makefile, so sites that _really_ need this (perhaps some huge
mail hubs) can still have it. The majority of FreeBSD boxes is better
served with an immediate delivery (and last time i've been asking on
the list, nobody complained).
messages like this:
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <ST506>
wd0: size unknown, using BIOS values: 615 cyl, 4 head, 17 sec, bytes/sec 512
npx0 at 0xf0-0xff irq 13 on motherboard
npx0: changing root device to wd0a
^^^^^^
The spurious 'npx0: ' pops up if you have a 386 with a 387 FPU.
Make the sound configuration a little neater
(see /sys/i386/isa/sound/Readme.freebsd)
Add support for the Microsoft Sound Source.
Document the sound options again.
Submitted by: Sujal Patel <[email protected]>
Obtained from: Voxware
NetBSD ld code except for local changes for dlopen() and friends and
the hashing on the minor value of the shlibs. We should be binary
compatible now with all their libraries.
Obtained from: NetBSD
directory (instead of the same directory as the source files) and that
#includes in those files do not contain the path to the source file.
Obtained from: J.T. Conklin via NetBSD
Support sliced devices better. E.g.:
`sh MAKEDEV sd0' creates [r]sd0 and [r]sd0s[1-4] as well as [r]sd0[a-h]
(the extra devices created by default won't hurt apart from wasting inodes).
`sh MAKEDEV sd0s1[a-h]' creates [r]sd0s1[a-h] (any partition creates all).
`sh MAKEDEV sd0s5' creates [r]sd0s5.
Support unit numbers 0-31 (was 0-6).
For wd:
Remove support for creating DOSpartitions wd*[i-m]. These will get removed
if you run MAKEDEV on `all' or on wd*.
Don't print debugging messages by default.
Initialize the compatibility slice here and not in the machine-dependent
code.
Fix initialization of the label for the whole disk slice.
Make it clear that write protection of labels doesn't apply when there is
no label.
table; arptab.c is really a hacked up version of arp.c that only
supports adding temporary entries. (This stuff is nasty -- I wish I
knew what was so wrong with SIOCSARP/SIOCGARP/etc... that made the
BSD developers decide to take it out.) The idea here is that the
client issuing the rarp is expected to be in the middle of booting
and would therefore be unable to answer arp queries from other machines
on the wire. Having rarpd stuff a temporary entry for the booting
host into the local arp table helps keep arp requests from going unanswered.
Also added ether_print() and ether_ntoa() to the ether_addr.c module.
Eventually I'll get ether_aton() and ether_hostton() written and
then this file can be dropped straight into libc. (Assuming no one
objects, of course. :)
be 486 chip sets that can't tolerate bursts > cache line size.
This should really made dependent on the particular buggy
chip sets, but for now we'll play safe ...
is a pain in ...wel.. trying to fix this
* from/to/via position indepenndant syntax
* "any" for 0/0 host address
* addf/addb default keyword in case you skip it..
* pass = accept new action, seems to be somewhat better
in particular cases
* on = via (as on ed0 instead of via ed0,loook at
reject tcp on ed0 from hacker )
Let "grey delete" be a function key (default is 0x7f)
Fix the xor cursor again..
Made the backspace key generate del as default
Made CTRL-space generate nul as default.
Feb. 10th snapshot. The keyboard probe in the bootblock seems to
have been singled out as the cause of these problems, so I've beefed it
up alittle. This pushes us right up to the edge of the size limit:
the second stage boot is now 7152 bytes in size, just 8 bytes under
the wire. On the other hand, the new probe now does almost exactly
what syscons does, so hopefully this will do the trick. It seems
to work properly on my hardware, but then so did the old probe.
compiler.
Be carefull about over usage of volatile, it really killed performance
in a few areas and there was a better place to make things volatile in
almost all cases. The driver can now receive at full speed without RNR
errors.
list or something since there are many contributors now but very few on
the order of folks like Bill or Satoshi or Jean-Marc.. This seems unfair.
Suggestions?
"Yes Virginia, there is a rarpd."
(Before anyone asks, this *not* the rarpd from NetBSD. It did come from
the same place as theirs, however.)
This is a port of the rarpd program included with the tcpdump-2.0
source code (which I finally unearthed after scrounging around
some of the darker corners of the Internet). It's as close to the
original as I could keep it except for the following changes:
- The original program was based on an older version of the Berkeley
Packet Filter which used different filter programming instructions.
Fortunately, an updated RARP packet filter is available right in the
BPF man page so this was easy to fix.
- The old code didn't know how to deal with variable length addresses
in ifreq buffers. This has been fixed.
- Some byte order weirdness had to be fixed. The sanity checks in
rarp_check() needed some htons()es, and the rarp_reply() function
needed to properly set the ether_type field in the ethernet header
to ETHERTYPE_REVARP before transmitting the packet, otherwise
the bytes in ether_type would wind up reversed. It is important to note
that using htons(ETHERTYPE_REVARP) will not work. This is odd, because
the NetBSD rarpd uses htons(ETHERTYPE_REVARP). (Praise be to tcpdump:
I would never have been able to track this silliness down without it.)
- The update_arptab() function has been castrated. It depends on
SIOCSARP which has been deprecated in 4.4BSD. The NetBSD people
don't seem to be using this function either. It wouldn't be too
hard to replace this with equivalent code from arp.c, but it
might not be necessary.
- I put together an ether_ntohost() support function that allows
both local (/etc/ethers) and NIS lookups. This stuff should go
in libc at some point, but nothing else seems to need it for now,
so it can wait a while.
As you may have guessed, you need to have the Berkeley Packet Filter in
your kernel in order to use this program. The good news is that together
with the recently added bootparamd, you can use finally use a FreeBSD
box to boot Sun boxes over the network. (This was my whole motivation
for getting this stuff to work: I have this one subnet that has a whole
bunch of Sun3 X-terminals on it with only two Sun4 workstations, both
of which are locked in peoples' offices. If those two machines crash
(and they do every so often) then none of the X-terms will boot. Now I
can use a spare PC that I have as a boot server. :)
New functions create - vm_object_pip_wakeup and pagedaemon_wakeup that
are used to reduce the actual number of wakeups.
New function vm_page_protect which is used in conjuction with some new
page flags to reduce the number of calls to pmap_page_protect.
Minor changes to reduce unnecessary spl nesting.
Rewrote vm_page_alloc() to improve readability.
Various other mostly cosmetic changes.
from the code in strftime.c . This affects both the library code
and all the commands using it (e.g. date +%s).
Note that %s is not required by ANSI, but we've already got it in 1.1.5.1.
Suggested by: [email protected] (Luigi Rizzo)
New functions create - vm_object_pip_wakeup and pagedaemon_wakeup that
are used to reduce the actual number of wakeups.
New function vm_page_protect which is used in conjuction with some new
page flags to reduce the number of calls to pmap_page_protect.
Minor changes to reduce unnecessary spl nesting.
Rewrote vm_page_alloc() to improve readability.
Various other mostly cosmetic changes.
thinking that it would work :( The install program never get a destination
directory. Here is another patch that should also be added. I think this
should be the last one for these makefiles :)
[Note: I realize that there are more things wrong than this, but this should
at least get the tree compiling again! -jkh]
Submitted by: John Hay <[email protected]>
than at compile time.
Should have same functionality as old libforms but with new mechanism.
Lots of new features that use the new mechanism are still to be added.
work if you don't have the obj link. Here is a patch for it. It will still
work if you don't have an obj link:)
(I stuck a ${DESTDIR} in front of the absolute path to /usr/include... /phk)
Reviewed by: phk
Submitted by: John Hay <[email protected]>
(a) bring back ttselect, now that we have xxxdevtotty() it isn't dangerous.
(b) remove all of the wrappers that have been replaced by ttselect
(c) fix formatting in syscons.c and definition in syscons.h
(d) add cxdevtotty
NOT DONE:
(e) make pcvt work... it was already broken...when someone fixes pcvt to
link properly, just rename get_pccons to xxxdevtotty and we're done
manual page can now also be read.
Change the references in MAKEDEV from com to tty and delete flog and add
sd instead.
Need much more work, but for today, after i lost my first changes through
a new sup :-), that's enough.
if all free blocks are in the same bucket (i.e. NRPOS == 1).
Else a free block is choosen, possibly from a different cylinder,
even if the block succeeding bpref was free ...
Submitted by: se
Try to deduce maximum number of PCI buses in system (working around
chip set bugs).
Better check for devices at multiple addresses (aliases).
Reviewed by: se
Submitted by: <[email protected]> Wolfgang Stanglmeier
DEC 21050 chip in particular, don't have specs of other such chips).
This should add support for Multiple-Ethernet PCI cards (e.g. Znyx 314).
Reviewed by: se
Submitted by: <[email protected]> Wolfgang Stanglmeier
may not properly initialize this field in all cases, and this would
result in very anti-social behavior (overwriting on some other random
device/location).
Submitted by: John Dyson
I hope I'm doing this right.
This is an initial version of bootparamd for FreeBSD based on a public
domain rpc.bootparamd implementation by a gentleman named Klas Heggemann.
This program has apparently been around for a while. The README explicitly
lists the code as public domain, so I guess it's safe to use.
This program is needed for booting diskless SunOS and Solaris machines.
rarpd is also required, but that's in the works too.
I have made two changes to this code:
- Implemented NIS lookups. If /etc/bootparams contains a '+' then the
bootparams map is consulted.
- Allow 0.0.0.0 as a user-specified router address. The SunOS rpc.bootparamd
returns this value in many cases.
to properly resolve some definitions in <nfs/nfs.h>. I suppose nobody noticed
this before because no one's tried to build bootparamd in FreeBSD until
now.
(Yes, you read that right: I've got bootparamd ready to go. And
rarpd is on the way. :)
Include proper files for 2.x.
Remove old unused argument to ixreset (int uba)
Nolonger convert ether_type to host byte order.
Use arp_ifinit in place of arpwhohas.
Change cb_ias to be non volatile.
o Supporting SYNC SIO device (But need a device driver)
- add "set speed sync"
o Fixing bug for Predictor-1 function.
o Add new parameter that re-sent interval for set timeout commands.
o Improving RTT (Round Trip Time) and reducing processor time.
- Previous Timer service was using polling, and now using
SIGALRM ;-)
- A 0.94beta2 will not work correctly....
-- Follows are additinal feature not including 0.94beta2
o Support Proxy ARP
- add "enable/disable proxy" commands
o Marging common routine in CHAP/PAP.
o Enhancing LCP/IPCP log information.
o Support local Authfication connection on port 300x and tty.
- You can set up pair of your "hostname -s" and
password in ppp.secret. if either ppp.secret file nor
your hostname line don't exist, It will notify a message
and working as same as previous version.(Backword compatibility)
- If you did set up them, It's allow connection but nothing to do
except help and passwd command.
- add "passwd yourpasswd" commands
o Support afilter - keep Alive filter that a packet can send/receiving
according to ifilter/ofilter but doesn't count it as preventing idle
timer expires.
- Same syntax of other filters.
o Fixing bugs reported by current user for previous one. Thanks !!
Reviewed by: Atsushi Murai ([email protected])
Fixes to ypbind:
- Correctly report the fact that we've bound to a new server when
logging the 'server OK' message.
- Report 'server not responding' just once instead of every
5 seconds while searching for a new server. (Prevents overstuffing
the syslog.)
- Apply patch from Sebstian Strollo to implement '-s' (secure) flag.
ypbind will reject connections from servers that do not originate
from a reserved TCP port.
- Apply patch from Sebastian Strollo to detect when a YP server has
crashed and come back up on a different port number.
is close to 1000000 / 960 usec so the confusion probably didn't matter.
Test for COMCONSOLE before testing for RB_SERIAL so that the RB_SERIAL
test can be optimized away if COMCONSOLE is 1.
Simplify and Uniformize style of previous commit.
(b) add a function callback vector to tty drivers that will return a pointer
to a valid tty structure based upon a dev_t
(c) make syscons structures the same size whether or not APM is enabled so
utilities don't crash if NAPM changes (and make the damn kernel compile!)
(d) rewrite /dev/snp ioctl interface so that it is device driver and i386
independant
This patch fixes the concurrency problem, and adds a possibly useful -f switch
(which you can read about in the man page :-) ). It also removes the absolute
path from the invocation of ctm. I'll write a note about how to use a script
with sendmail and procmail or some such, and people can fix their PATH there.
BTW, this patch changes ctm_rmail.1, ctm_rmail.c and error.c in the ctm_rmail
directory.
Stephen.
Reviewed by: phk
Submitted by: Stephen McKay <[email protected]>
I'm never going to generate one, so this is a guard against hackers mostly.
Reviewed by: phk
Submitted by: Stephen McKay <[email protected]>
Obtained from:
Now I know that there was talk of moving it to the release/Makefile or the
etc/Makefile, but I don't think it was ever decided where.
Reviewed by: phk
Submitted by: John Hay <[email protected]>
the values that it doesn't print by defaults. This seems wrong. I want
to be able to see the total number of sectors more than edit it. The
default d_secperunit of (sectors/track * tracks/cylinder * cylinders) is
bogus if sectors/track is only an approximation and more bogus if
sectors/track and tracks/cylinder are dummy values such as 4096 and 1
to defeat ufs's pessimizations.
labels.
Please test the slice/label features:
cd /dev; sh MAKEDEV svn0
cd /var/tmp; dd if=/dev/zero of=vnfile bs=8192 count=1024
vnconfig -c /dev/rvn0 /var/tmp/vnfile
fdisk /dev/rvn0 # invent a geometry, create one BSD partition
disklabel -r -w vn0 floppy # a convenient (bogus) label
disklabel -e vn0 # edit label to match device
newfs /dev/rvn0a
mount /dev/vn0a /mnt
...
The steps after the fdisk could name the device vn0s1 instead of vn0.
Fix the sign of the adjustment after writing a label.
Writing of labels should work now.
Merge adjust_label() into fixlabel(). Detect more errors and don't
write if there is an error. Adjust sectors/unit and total sectors
to the numbers on the slice.
Add a function dsname() to print slice device names consistently, and
use it.
If you invoke config with the `-n' flag or have NO_CONFIG_CLOBBER in
your environment, config will behave the same way it used to. This is
now _documented_ as well. Rip out all the CONFIG_DONT_CLOBBER cruft;
some of it wasn't even correct anyway.
PCI BIOS mappings are retained, except if option PCI_REMAP
is specified in the kernel config file.
There is now a list of attach addresses, and the first
address that seems to make some device registers appear
is chosen.
Reviewed by: se
Submitted by: wolf
Removed screensavers from syscons, they are now LKM's. This makes it
possible to do some really "interesting" screensavers...
Fixed bug that sometimes caused garbage to appear when leaving
"scroll-lock" history.
Reformattet indentation, it got too deep for a normal 80 pos screen.
Split up in syscons.c & syscons.h for use with the saver-lkm's.
Temporarily removed -s option from vidcontrol, savers should now
be loaded with modload.
that 9 bits aren't lost in the conversion. Changed all callers to expect
this. This allows paging on large (>2GB) filesystems.
Submitted by: John Dyson
Use request==VM_ALLOC_NORMAL rather than object!=kmem_object in deciding
if the caller is "important" in vm_page_alloc(). Also established a new
low threshold for non-interrupt allocations via cnt.v_interrupt_free_min.
vm_pageout.c:
Various algorithmic cleanup. Some calculations simplified. Initialize
cnt.v_interrupt_free_min to 2 pages.
Submitted by: John Dyson
Various more tweaks from John Dyson to improve read ahead calculations.
vfs_subr.c:
Only wakeup if numoutput is 0 in vwakeup().
Submitted by: John Dyson
metadata aren't thrashed by regular file I/O.
Added mechanism to limit the amount of outstanding I/O on a given vnode.
Pagedaemon wakeup policy changed to skew priority a little in favor of
file caching.
Slight code reorganization to improve clarity.
Added a few more comments.
Submitted by: John Dyson
IP addresses and/or protocol+port, but in the case where both are
supplied, it happily accepts the command but ignores the proto+port
It also attempts to handle the case where the second IP address
is omitted, but this doesn't work.
Reviewed by: [email protected]
Submitted by: [email protected]
commands per target. I could have followed the route of the ncr driver
and gone to great lengths to get the SCSI subsystem to support more, but
I think I'll use the time saved to help Julian and Peter make tagged
queuing a better handled generic feature. This also includes some comment
and enum clean up and a possible fix for the hanging PCI controllers.
the same as when initializing the in-core copies. Adjust checksums in
labels after adjusting labels. This finishes fudging the on-disk label to
make it coherent with the in-core label.
Handle EIO during initialization better.
Initialize the compatibility slice to the whole disk If there are no real
slices.
Don't warn about adjusting offsets in the label to make the 'c' partition
start at 0. The 'c' offset is now always absolute on-disk and 0 in-core
so an adjustment is usually required.
Don't confuse LABEL_PART with RAW_PART so much.
Check for partitions being within slices differently.
pager(). Almost completely rewrote vm_mmap(); when John gets done with
the bottom half, it will be a complete rewrite. Deprecated most use of
vm_object_setpager(). Removed side effect of setting object persist
in vm_object_enter and moved this into the pager(s). A few other
cosmetic changes.
returned to user mode without enabling ASTs. The problem fixed itself
at the next syscall or non-FPU trap, if any. It hung the system for
a test process that masked SIGFPE's and divided by zero. The faulting
division was returned to endlessly and this gave plently of opportunities
for the swi_ast_phantom case to be reached; after it was reached the
system hung because the ASTs for preemption and SIGINT handling were
disabled.
via sysctl(8). The initial value of maxprocperuid is maxproc-1,
that of maxfilesperproc is maxfiles (untill maxfile will disappear)
Now it is at least possible to prohibit one user opening maxfiles
-Guido
Submitted by:
Obtained from:
the same as the changes made in the repository. This is often seen by
people with remote CVS trees that have applied their local patches to the
master site. a 'cvs update' will show bogus conflicts.
Obtained from: CVS mailing list, Stig<[email protected]>
In diffutils 2.6 and 2.7, diff3 -A complains about identical overlapping
changes. They're different from the ancestor but not from each other...
Why bother? The patch below fixes this nonsense and preserves [B]ackwards
compatiblity with the -B flag (also --show-bogus-conflicts).
Party on...
Stig
Since functions will come and go from libcompat as they are deprecated
it makes no sense to build a shared library out of it as it will change.
Based on freedback from Terry and Jonas on the mailing lists.
Slight change to reverse collapsing so that vm_object_deallocate doesn't
have to be called recursively.
Removed half of a previous fix - the renamed page during a collapse doesn't
need to be marked dirty because the pager backing store pointers are copied
- thus preserving the page's data. This assumes that pages without backing
store are always dirty (except perhaps for when they are first zeroed, but
this doesn't matter).
Switch order of two lines of code so that the correct pager is removed
from the hash list. The previous code bogusly passed a NULL pointer to
vm_object_remove(). The call to vm_object_remove() should be unnecessary
if named anonymous objects were being dealt with correctly. They are
currently marked as OBJ_INTERNAL, which really screws up things (such as
this).
requires complications to adjust the offsets to relative when a block
containing the label is read and back to absolute when such a block is
written. The adjustment is not made on the whole disk slice.
Don't allow setting the offset of partition C to nonzero in in-core labels.
This will cause some (nonstandard) disktab entries to fail. They will
need to be changed to have relative offsets (and no partitions outside
of the slice).
Don't write protect the (nonexistent) label on the whole disk slice.
Writing labels and bootstraps should work right now (except if there is
no DOSpartition table).
just thinking about it.
Two changes need to be made to allow 'config kernel swap generic' to
work properly without requiring any compile-time flags:
/usr/src/usr.sbin/config/mkswapconf.c: we need to define a dummy stub
for the setconf() function to replace the one in swapgeneric.c that
isn't available in non-generic configurations.
/usr/src/sys/i386/i386/autoconf.c: the -a boot flag causes setroot()
to be skipped and lets setconf() prompt the user for a root device.
If you skip setroot() in a non-generic kernel, you could get severely
hosed. To avoid this, we silently ignore the -a flag if rootdev != NODEV.
(rootdev is always initialized to NODEV in swapgeneric.c, so if
we find that rootdev is something other than NODEV, we know we're
not using a generic configuration.)
probation.. Another vanishing act and I won't hesitate to nuke this back
out again. He hasn't been heard from very much since he was over here to
visit! :-)
2) bump reference counts by 2 instead of 1 so that an object deallocate
doesn't try to recursively collapse the object.
3) mark pages renamed during the collapse as dirty so that their contents
are preserved.
Submitted by: John and me.
in an (unlikely) border case (maxgroups==1 and the user is on
an /etc/group line for the same group and that group only ...).
Now this case is dealt with as before ...
Test for correct execution of cache test script by NCR,
and give meaningful error description if it fails.
(A cache problem was reported before.)
Don't wait forever for cache test to complete (to protect
against faulty hardware).
Submitted by: wolf
444 -> root.wheel
root -> root.wheel
uucp -> uucp.wheel (perhaps this should be .dialer, but .wheel is safer)
missing -> root.wheel
chown to root is usually bogus because mknod had to be run by root to
create the inode. Setting the group explictly is currently necessary
because MAKEDEV does nothing to ensure that its working directory has
a suitable group.
Driver authors! Please fix any bogons in MAKEDEV that involve your
drivers. The sound devices are still world writable...
briefly over it, and see some serious architectural issues in this stuff.
On the other hand, I doubt that we will have any solution to these issues
before 2.1, so we might as well leave this in.
Most of the stuff is bracketed by #ifdef's so it shouldn't matter too much
in the normal case.
Reviewed by: phk
Submitted by: HOSOKAWA, Tatsumi <[email protected]>
for now (there are too many minors to create by default). The special
sliced disk case ssd*|svn*|swd*) can almost replace the standard disk
case sd*|vn*|wd*) now (it just creates a few more devices), but there
will have to be special cases to allow creating slices 6-31 and partitions
on slices 2-31.
Fix bogus default cases.
Slice 0 is now for the first BSD slice. The first BSD slice is
the first DOSpartition with id 0xa5 or the whole disk if their
are no DOSpartitions (except the latter is not yet implemented).
Existing partitions on it work the same as in 2.0 except the
'd' partition is no longer special and partitions are relative
to the skice.
Slice 1 is now for the whole disk and gets a read-only label
describing the disk. Previously, slice 0 was for the whole disk
and there was no label on it.
Slices 2-31 are for DOSpartitions. Slice 0 is an alias for one
of these if there is a BSD slice. Previously, slices 1-31 were
for DOSpartitions.
diskslice_machdep.c:
Expand whole disk slice to include all DOSpartitions. More work
is required for >1024 cylinders and to rewrite the label iff the
driver is unsure about the geometry.
subr_diskslice.c:
New function dsisopen() to help handle media changes.
mapping from numbers to names is messy for backwards compatibility.
E.g., for driver "sd", unit "0":
slice 0: omit the slice number for compatibility; names are sd0[a-h].
slice 1: omit the partition letter 'c' because the whole disk device
shouldn't have anything to do with partitions; sd0 is the
only name.
slices 2-31: subtract 1 from slice number to compensate for the
compatibility slice 0; names are sd0s[1-30][a-h].
Support slice numbers in device names. The syntax is `<driver name>
[<unit number>] ['s' <slice number>] [<partition letter>]'. Only
`['s' <slice number>]' is new here. The slice number defaults to 0
so that there is no change in the output from config if this new
feature is not used.
Replace some magic disk numbers by `dk' slice and label macros.
mkswapconf.c:
Improve the output formatting:
Generate <> style includes.
Print minor numbers in hex so that slice numbers are easy to see and edit.
Print the rootdev and dumpdev names in comments like the swapdev names.
Add the `lc' option to default. Having getty understand the issues of
CAPS-only terminals is a nop these days, but `lc' avoids hassles for
people with CAPS-only user names.
Suggested by: Don Yuniskis
weekly:
Modify the call to makewhatis, now that our makewhatis can take the
entire ${MANPATH} as a single argument.
The existing ypbind exhibits some truly anti-social behavior. After
initially establishing a binding with an NIS server, the following events
take place:
- ypbind waits for 60 seconds before trying to broadcast a ping again
- after the 60 seconds expires, ypbind sends out broadcasts every 5 seconds
come hell or high water.
These broadcasts travel far and wide, even to NIS servers in other domains
which dutifully log the packets even though they don't respond to them.
This leads to lots of unnecessary traffic and bloated log files.
This behavior has been fixed/changed. Here's what happens now:
- We still broadcast every 5 seconds at startup, just like before.
- Once bound, we send out packets once every 60 seconds to the server
we're bound to AND NO ONE ELSE.
- If we fail to receive a reply from our server within FAIL_THRESHOLD
seconds, we assume our server has croaked and go back to broadcasting
everywhere every 5 seconds again until somebody answers. FAIL_THRESHOLD
is currently set to 20 seconds.
Other fixes/improvements:
- ypbind now logs 'server not responding' and 'server OK' messages where
appropriate.
Thanks to Thomas Graichen <[email protected]> for
reporting the problem and guilt-tripping me into fixing it. :)
when ttselect() is improved. This requires using an array of tty structs
and not using ttymalloc().
Fix an off by 1 error. Some caclulations seem to be off by a factor
of NCY. NCY defaults to 16, which gives 256 tty structs occupying
0xd000 bytes. The minor number encoding only allows 16 ttys.
Update the types of timeout functions to 2.0.
- Overflow now calculated right
- Close works ok,does not looses tty
- Better overflow handling now the snooping stops
on overflow,but programm notified and can reconnect if
it want to..Default maximal buffer set to 664 K and this
is probably too much..:)))
Utility still to come
Restore fixes to flushing that were lost in the previous commit.
Clean up snoop changes.
Add my TODO list from 1.1.5. The improvements in 1.1.5 should be "obtained"
first.
tape drive. I traced it to sys/scsi/scsi_base.c where some code were added
to print the return values of the sense command. My tape drive returned a
extended flags value of 0x20, so the key that is the lower 4 bits, is 0.
The code uses "key-1" to index into a table and then the kernel go to never-
never land.
Here is a fix for this. Will somebody please apply it?
Submitted by: John Hay
It boots FreeBSD from a running MS-DOS system.
It's compiled using some MS-DOS tools, but there is a binary
hidden in the uuencoded file. (Go ahead, flame me if you can come up
with a solution for the problem. Just saying "this is bad" doesn't count!)
Rod, you were right: one would have to deal with weird interfaces to the
memory managers, and it seems that Christian found them all, and made them
work.
Thanks Christian!
Reviewed by: phk
Submitted by: DI. Christian Gusenbauer <[email protected]>
Christians README:
------------------
Hi Everybody!
This is version 1.5 of "fbsdboot", a program that allows you to boot a kernel
from a MS-DOS partition or a FreeBSD partition. This program runs using DOS.
It works with various memory managers (like EMM386, 386MAX) under certain
circumstances.
First, a FreeBSD kernel is always loaded to memory starting at 0x100000. To
assure that loading the kernel *does not* overwrite memory used by memory
managers, high memory for the kernel is allocated and after loading the kernel
it's moved to 0x100000.
Second, there are many ways to switch to protected mode which is necessary to
start the kernel. Each BIOS gives you the possibility to use INT15H (AH=89H)
to do that. But some memory-managers like 386max does not allow you to use
this method.
An other way to do the switch is to use DPMI services, but they do not
guarantee, that the protected mode application is executed with privilege
level 0. Therefore this method is *not* used.
VCPI services offer another way to switch to protected mode, and VCPI servers
are built into "emm386.exe", "386max" and "qemm". That's why, this method is
implemented in fbsdboot.exe.
Fbsdboot.exe tries to switch to protected mode using VCPI services. If they're
not available INT15H is used to do the switch. If that fails, it's not possible
for this version of fbsdboot.exe to boot a kernel :-(.
You can get commandline options of fbsdboot if you start it with "-?" as option!
I don't know, if fbsdboot works with QEMM, as I don't have the possibility to
test it.
Enjoy and have fun!
Christian.
[email protected]
PS: Many thanks to Bruce Evans for his assistance!
Submitted by: Rich
Make conditionals on BIOSWAIT consistent with usage in io.c.
If you had 'BOOTWAIT=0' in your /etc/make.conf then biosboot wouldn't
compile. It was '#if' in io.c and '#ifdef' in probe_keyboard.c so I
changed the latter to '#if'.
Even if BOOTWAIT is undefined then '#if BOOTWAIT' becomes
'#if 0' so it should compile either way with this change.
The "strings" program chokes if you try using "-n".
>How-To-Repeat:
Try "strings -n SOMENUMBER SOMEFILE".
>Fix:
Here's a "diff -u" patch that corrects the problem.
Submitted by: Lon Willett <lon%[email protected]> via NetBSD
in the script. The result is the following :
203 [23:47] root@keltia:/build/cvs-1.4A2# manctl
/usr/sbin/manctl: 165: Syntax error: ";" unexpected
Here is the fix :
Submitted by: Ollivier Robert <[email protected]>
New config option "NCR_IOMAPPED" makes the driver use port I/O.
Put back in 53c815 defines, submitted by Mikael Hybsch <[email protected]>.
These had got lost between cvs rev. 1.14 and now ...
pci.c:
Really write config space register.
Assign ports starting at 0xbc00.
Submitted by: wolf
Reviewed by: se
expiration timer of anything which would expire later than that. (There
should be a way to call this from ip_sysctl() as well, but there currently
isn't.)
high load:
1) If there ever get to be more than net.inet.ip.rtmaxcache entries
in the cache, in_rtqtimo() will reduce net.inet.ip.rtexpire by
1/3 and do another round, unles net.inet.ip.rtexpire is less than
net.inet.ip.rtminexpire, and never more than once in ten minutes
(rtq_timeout).
2) If net.inet.ip.rtexpire is set to zero, don't bother to cache
anything.
Users-beware..
It is tested and working for me but probably have some bugs i
didn't noticed so test it and reply...
It can:
look at what's sent to the user from tty device
snoop on pty's,vty's and serial tty's
It (still) can't:
write to tty
see what user types in local echo mode
It is probably bad styled and
very dependant on tty_pty.c,sio.c and syscons.c
I would be really happy if another ppl would make their
changes because i am not sure this is the best snoop
we can have..but it is good..:)))))
I took 53 and it was too late when Jordan sayd
it better been 60..besides i have no clue how to make it 60..
Jordan- pleeease don't kill me..(This is also useful(??) device..)
the symlinks for yppasswd & friends (we still can't use hard links
because passwd is installed immutable). This would have been simpler
if the LN_FLAGS variable hadn't chosen to wait until now before leaping
out of the /usr/share/mk directory and biting me in the ass. (And thus,
I was enlightened.)
EDSS1 is the "Euro-ISDN", 1TR6 is the soon obsolete german ISDN Interface.
Obtained from: Dietmar Friede <[email protected]> and
Juergen Krause <[email protected]>
This is only one part - the rest to follow in a couple of hours.
This part is a benign import, since it doesn't affect anything else.
ports for the destination IP addr/port.
Nobody reported this btw , while a lot of other things reported-
probably ppl does not use destination ports at all????
entire kernel.
Unfortunately we didn't send him a copy of the style guide before he did it.
I'm trying to find all the benign and downright sound bits and will commit
them without any other explanation than "YF fix" if they are merely cosmetic.
Reviewed by: phk
Submitted by: [email protected] (Yves Fonk)
add a an ioctl call to set the transfer block size (SNDCTL_DSP_SETBLKSIZE)
and add the select system call to the drivers. They also fix a problem with
the #EXCLUDE macros for the PAS-16 card.
Submitted by: Jim Lowe <[email protected]>
Bruce finally caught this bogon for me, Thank you Bruce !
Due to some part of the VM/buffer/pmap magic doing clustering, this bogon
managed to work better than 99.9% of the time. Amazing.
If You ever again see a weird message from the gzip code, please tell me.
in here that just made it a heck of a lot more confusing to maintain.
Somebody like Joerg can reality-check this at some point, when they have more
time. For now, it works.
now we're back to the old way. By way of amends, I cleaned up all the
casting evils and generally neated this file up as much as possible. It
still, however, needs to die.
The group was wrong if MAKEDEV was run in a directory with group other
than wheel. This may have messed up the group in recent SNAPs
(sysinstall/obj should have group bin).
Reset the umask to 77 after running MAKEDEV.local. Some cases depend on
the 77 default. MAKEDEV.local and all cases should probably set the
umask explictly and not depend on a default. Most cases already set it.
so that the interface won't have the effect of blocking other senders
during bulk transfers (i.e. hogging the ethernet). It improves performance
in all of my tests by reducing collisions and I believe it to be a Good
Thing.
Bob Braden <[email protected]>.
NB: This has not had David's TCP ACK hack re-integrated. It is not clear
what the correct solution to this problem is, if any. If a better solution
doesn't pop up in response to this message, I'll put David's code back in
(or he's welcome to do so himself).
I have seen two strange things in it :-).
The first: in CLEANFILES is CPIO3 referenced, that leads to the
deletion of half of the scripts that are in the source. Intended ?
Second: The comment above the CPIO3= line says that bininst must be
the last on the floppy, but setup follows it now ?
And I reply:
This was all wrong! Fixed! Thanks!
Submitted by: ats
TS_WOPEN state when CLOCAL is toggled from on to off while there
is no carrier. There is no way back, and with sio there is no way
forward either (TS_ISOPEN will never be set again for the current
open). This bug was observed in 1.1 and was fixed in 1.1.5.
`depend' wasn't supported. This seems to have only broken `make depend'
in gnu/usr.bin/ld.
bsd.prog.mk:
Build the man pages in ${MANDEPEND} at build time.
1) ypserv is started with nis_serverflags, not yppasswddflags (that's what
I get for cutting & pasting without paying attention).
2) ypbind can also be started with arguments, so turn nis_client to
nis_clientflags.
isn't important; it is only used to prevent symlink loops from looping
forever. 32 is a quite reasonable default.
Submitted by: Ed Hudson <[email protected]>
1. add iosize command, and show it in `ls'
2. add a probe command
3. add an attach command
[the latter 2 do the obvious thing - call the device's routine and print the
status returned].
newline must be part of the pattern space i.e. `echo a|sed -e P' must print
a
a
and not
aa
This is consistent with gnu sed, SunOS, Ultrix (and probably others!)
We pretend we have one head with two megabyte worth of sectors per cylinder.
The code try to access another head in what it belives to the same
physical cylinder, because it belives that it would be faster than
waiting for the next free sector under this head to come around.
Most modern drives doesn't have a "classical" geometry, and thus
we end up fooling ourselves doing the above optimization. With this
change we will fill a cylinder sequentially if we can, and thus get
much more mileage from the track-buffer/cache built into the drives.
As a result a lot of seeks to the next or previous track should be
avoided by this.
(My disk is a lot less noisy actually...)
You can still get the old behaviour, by specifying zero for the
numbers.
This will also solve the problem with newfs barfing at really big
drives.
Obtained from: adult advice from Kirk.
You will normally have to have a VLB or other 32bit IDE "controller" for
this to work.
Depending on your setup, this may gain you 20-100 % speed from your disk.
Reviewed by: phk
Submitted by: [email protected]
have three variables:
EXEC_DEPENDS - A list of "prog:dir" pairs of other ports this
package depends on. "prog" is the name of an
executable. make will search your $PATH for it and go
into "dir" to do a "make all install" if it's not found.
LIB_DEPENDS - A list of "lib:dir" pairs of other ports this package
depends on. "lib" is the name of a shared library.
make will use "ldconfig -r" to search for the
library. Note that lib can be any regular expression,
and you need two backslashes in front of dots (.) to
supress its special meaning (e.g., use
"foo\\.2\\.:${PORTSDIR}/utils/foo" to match "libfoo.2.*").
DEPENDS - A list of other ports this package depends on being
made first. Use this for things that don't fall into
the above two categories.
DEPENDS behaves exactly like before, so old Makefiles will still work
the same. The two variables are lists of pairs as described above.
For instance, if your program depends on unzip and libjpeg.5.*, use
the following definitions:
EXEC_DEPENDS= unzip:${PORTSDIR}/archivers/unzip
LIB_DEPENDS= jpeg\\.5\\.:${PORTSDIR}/graphics/jpeg
gmake:${PORTSDIR}/utils/gmake is automatically added to EXEC_DEPENDS
if USE_GMAKE is defined.
If NO_DEPENDS is defined, the list will just be printed out one by one.
Add a missing apostrophe that suggests inverting the frequency to get
tick size. It read better before because `CLK_TCK' suggests a tick
size although it is actually a frequency.
Define CLK_TCK only if _ANSI_SOURCE is not defined.
Don't include <machine/limits.h> to get the definition of CLK_TCK.
CLK_TCK should never have been defined there, and the inclusion
polluted the namespace.
message instead of relying on the fact that we are scheduled to send them.
The old method worked 99.9% of the time, but someone reported some periferals
that did MSG_REJECT at odd times (sometimes before we could send an SDTR
or WDTR) that we would construe as the response to an SDTR or WDTR message.
This also removes a possible race condition where after a bus reset (the
result of a command time out not during intial probe time), we might queue
two commands both requesting SDTR, WDTR or both.
i reported today earlier..tested and works OK..
( To those who want to experience bug try running aub
with old version of socket.ph and with new one or just any
perl script "requiring " <sys/socket.ph> or <sys/cdefs.ph> )
in serious system instability. Changed a B_INVAL to a B_NOCACHE so that
buffer data is properly disposed of.
Submitted by: John Dyson, Rick Macklin, and [email protected]
as an NIS client. The pw_breakout_yp routines that are used to populate the
_pw_passwd structire only do anything if the bits in the pw_fields member
_pw_passwd are cleared. Unfortunately, we can get into a state where
pw_fields has garbage in it right before the YP lookup functions are
called, which causes the breakout functions to screw up in a big way.
Here's how to duplicate the problem:
- Configure FreeBSD as an NIS client
- Log in as a user who's password database records reside only in
the NIS passwd maps.
- Type ps -aux
Result: your processes appear to be owned by 'root' or 'deamon.'
/bin/ls can exhibit the same problem.
The reason this happens:
- When ps(1) needs to match a username to a UID, it calls getpwuid().
- root is in the local password file, so getpwuid() calls __hashpw()
and __hashpw() populates the _pw_passwd struct, including the pw_fields
member. This happens before NIS lookups take place because, by coincidence,
ps(1) tends to display processes owned by root before it happens upon
a proccess owned by you.
- When your UID comes up, __hashpw() fails to find your entry in the
local password database, so it bails out, BUT THE BITS IN THE pw_fields
STRUCTURE OF _pw_passwd ARE NEVER CLEARED AND STILL CONTAIN INFORMATION
FROM THE PREVIOUS CALL TO __hash_pw()!!
- If we have NIS enabled, the NIS lookup functions are called.
- The pw_breakout_yp routines see that the pw_fields bits are set and
decline to place the data retrieved from the NIS passwd maps into the
_pw_passwd structure.
- getpwuid() returns the results of the last __hashpw() lookup instead
of the valid NIS data.
- Hijinxs ensue when user_from_uid() caches this bogus information and
starts handing out the wrong usernames.
AAAARRRRRRRRRGGGGGGHHHHHHHHHH!!!
*Please* don't tell me I'm the only person to have noticed this.
Fixed by having __hashpw() check the state of pw_fields just before
bailing out on a failed lookup and clearing away any leftover garbage.
What a fun way to spend an afternoon.
definitions taken from the PCI specs. Part of them were typed
in by Wolfgang Stanglmeier, the (at that time unneeded) rest
by Charles Hannum (thanks !).
may be the result of reselect following too fast for
the driver to notice. Not the final solution, but the
problem has been seen only with very few devices.
Reviewed by: se
Submitted by: wolf (Wolfgang Stanglmeier)
Fixed long standing bug in freeing swap space during object collapses.
Fixed 'out of space' messages from printing out too often.
Modified to use new kmem_malloc() calling convention.
Implemented an additional stat in the swap pager struct to count the
amount of space allocated to that pager. This may be removed at some
point in the future.
Minimized unnecessary wakeups.
vm_fault.c:
Don't try to collect fault stats on 'swapped' processes - there aren't
any upages to store the stats in.
Changed read-ahead policy (again!).
vm_glue.c:
Be sure to gain a reference to the process's map before swapping.
Be sure to lose it when done.
kern_malloc.c:
Added the ability to specify if allocations are at interrupt time or
are 'safe'; this affects what types of pages can be allocated.
vm_map.c:
Fixed a variety of map lock problems; there's still a lurking bug that
will eventually bite.
vm_object.c:
Explicitly initialize the object fields rather than bzeroing the struct.
Eliminated the 'rcollapse' code and folded it's functionality into the
"real" collapse routine.
Moved an object_unlock() so that the backing_object is protected in
the qcollapse routine.
Make sure nobody fools with the backing_object when we're destroying it.
Added some diagnostic code which can be called from the debugger that
looks through all the internal objects and makes certain that they
all belong to someone.
vm_page.c:
Fixed a rather serious logic bug that would result in random system
crashes. Changed pagedaemon wakeup policy (again!).
vm_pageout.c:
Removed unnecessary page rotations on the inactive queue.
Changed the number of pages to explicitly free to just free_reserved
level.
Submitted by: John Dyson
argument is now more than just a single flag. (kern_malloc.c)
Used new M_KERNEL value for socket allocations that previous were
"M_NOWAIT". Note that this will change when we clean up the M_ namespace
mess.
Submitted by: John Dyson
some comparisons as it is more correct (we want the kernel page tables
included).
Reorganized some of the expressions for efficiency.
Fixed the new pmap_prefault() routine - it would sometimes pick up the
wrong page if the page in the shadow was present but the page in object
was paged out. The routine remains unused and commented out, however.
Explicitly free zero reference count page tables (rather than waiting
for the pagedaemon to do it).
Submitted by: John Dyson
*so many problems*.. Too bad the snaps themselves don't get made as a
consequence.. :-)
Bump the date forward Yet Another Day. David has some changes he wants to
see rolled in, so I guess we're down for Feb 2nd as the snap date!
correctly (specified wrong fields to awk). Note that the files in question
are noe the local /etc/master.passwd and /etc/passwd files: this Makefile
expects there to be a seperate master.passwd file under /var/yp for NIS
database creation.
Submitted by: wolf (Wolfgang Stanglmeier)
Most PCI specific files moved from sys/i386/pci to sys/pci.
One PC specific file (pcibus.c) new in sys/i386/isa.
Submitted by: wolf (Wolfgang Stanglmeier)
Obtained from:
Most PCI specific files moved from sys/i386/pci to sys/pci.
One PC specific file (pcibus.c) new in sys/i386/isa.
of hard links: since passwd is installed immutable, an attempt to make
a hard link to it during a 'make install' would fail. I didn't notice
this conflict because my /usr directory is an NFS filesystem mounted from a
SunOS server, so the special file mode flags had no effecti when I tested
everything on my machine. Live and learn.
one line long.
Fixed a bug in the input field with cursor positioning at the end of
the field.
Make the print_status function available to apps so they can print
status messages.
Updated the example for the new fib parser.
executes after it finishes updating the raw master.passwd file. The script
is just there to invoke /var/yp/Makefile to build new maps and yppush them.
We could have yppasswdd run /var/yp/Makefile directly, but this allws a bit
more flexibility: the user may decide to run some other commands too.
- FreeBSD's NIS server can supply a master.passwd map, which has
more fields in it than a standard passwd map, so we need a
_master_pw_breakout() fuction.
- When doing passwd map lookups, look for master.passwd.* by attempting
a _yp_first() on master.passwd.byname. If it exists, we're being served
by a FreeBSD NIS server and we should use this map.
- If we aren't the superuser, retrieve only the standard passwd maps.
If we're being served by a FreeBSD system, then the passwd map has
no passwords in it, and it won't serve us the master.passwd map unless
we're superuser anyway.
There's a small speed hit for the superuser inherent in the check for
the master.passwd map, but this lets us dynamically decide what to do
rather than rely on a non-standard config file somewhere. Since all
of this is bypassed for normal users, they shouldn't notice the
difference.
This is a ported/modified version of the yppush program from the
yps-0.21 package from the NYS project. This program is used to propagate
updated NIS maps from an NIS master to an NIS slave. It's normally invoked
by /var/yp/Makefile.
This version of yppush has been modified in the following ways:
- Cleared up several Linux/BSD incompatibilities, largely involving
header files.
- converted from GDBM to DB with extreme predjudice. (well, not really...)
- removed lots of ugly debugging code that really didn't do anyone any good.
- Fixed a couple of inaccurate/badly formatted error messages.
- Renamed some functions to avoid collisions with certain YP routines
hidden inside libc.
- Small signal handling kludge: Linux has different struct sigaction
that us.
- Incorporated some functions from the yps-0.21 library that yppush was
dependent on.
Like ypxfr, this works, but could use come cleaning up.
This is a ported/modified version of the ypxfr program from the yps-0.21
package from the NYS project. This program is normally invoked by ypserv
when it receives a yppush command from an NIS master. It can also be
run from the command line to grab copies of maps when initializing a
slave server.
This program has been hacked in the following ways:
- rpcgen'ed new yp_xdr.c, yp_svc.c and yp_clnt.c files. The old ones were
rather grody.
- Changed certain function names (prefended a _ to them) to avoid conflicts
with certain functions lurking within libc. One major problem here is
that ypxfr needs to bind to a YP master in order to work correctly,
but it can't use the _yp_bind function inside libc because that
function only lets you bind to a domain, not a specific host. Lots
of head scratching here.
- Converted from GDBM to DB at gunpoint.
- Removed lots of really nasty looking DEBUG code to try to reduce clutter.
- Incorporated some of the library code supplied with yps-0.21 on which
ypxfr was dependent.
This program still needs to be cleaned up just as a matter of principle:
I get all icky just looking at it sometimes.
This is a ported/modified version of yppasswd from the NYS yppasswd-0.5
package. This package has code in it from both Olaf Kirch and Theo
de Raadt. There are GPL references and BSD-style copyright all over the
place... hopefully I won't get flamed into oblivion for commiting this.
This program has been modified from the original in the following ways:
- Changed the ALLOW_CHFN and ALLOW_CHSH compile-time options into
run-time options.
- Demolished the password update functions and replaced them with
routines to handle FreeBSD-style passwordd databases. It is expected
that a seperate master.passwd file will be maintained for use with
the NIS maps. yppasswd will have to be told where it is:
% yppasswdd -m /var/yp/master.passwd
A /var/yp/passwd file will be generated from /var/yp/master.passwd by
/var/yp/Makefile. When yppasswdd has finished modifying the master.passwd
file, it will invoke /usr/libexec/yppwupdate, which is a script that
will run /var/yp/Makefile to generate new maps and push them.
Note that there are copies if pw_util.c and pw_copy.c here. This is
deliberate: they are *not* identical to the originals. Very similar, yes,
but not identical. *sigh*
This is a hacked-up port of the ypserv-0.11 server from the NYS project
written by Peter Eriksson.
The original package included some map creating and dumping tools and
was based on GDBM. This version has been modified in the following
ways:
- GDBM replaced with DB and many weird hacks made to the read_database()
function because of this.
- implimented the ypxfr service (using ypxfr from the yps-0.21 package,
aso from the NYS project)
- added code to check the TCP port from which NIS requests originate:
the server will refuse to serve the master.passwd.{byname|byuid} maps
if the request doesn't come from a privileged port. Normally, only the
superuser can issue such a request. Requests for the passwd.{bynam|byuid}
maps aren't affected. There will be a small change made to getpwent.c
in libc to complement this.
- added code to do DNS lookups via actual resolver queries instead of
relying on gethostbyname() and friends. The author noted in the original
documentation that a loop condition could arise where the server would
query itself for hostsname lookups. Using direct DNS lookups prevents
this from happening.
- added code to properly fork() the server into the background unless
invoked with the -debug flag.
- Added combined syslog/perror function.
- fixed a few bugs (which were probably introduced by all the other
changes)
- Created a bmake Makefile.
Note that this package can be linked against the tcp_wrapper package
to provide address-based authentication, but this isn't done by default
since the tcp_wrapper package isn't part of FreeBSD.
This program is used for both generating and dumping NIS maps. It's very
similar to the 'makedbm' command in SunOS. This program was ported from
the yps-0.21 package. It's close to the original except for the GDBM to
DB conversions. This was simple compared to the other YP components.
This is the first round of changes to incorporate YP server functionality
into FreeBSD. This particular change allows passwd to change either the
local or NIS password, as well as the NIS GECOS and shell information.
Essentially, I've taken passwd(1) and yppasswd from the yppasswd-0.5
distribution (which is part of the NYS project -- a project to provide
a GNU GPL'ed suite of NIS tools) and rammed them into each other
at high speed. I've tried my best to make this co-exist with the
Kerberos stuff, but since I don't run Kerberos I don't have an easy
way to verify that it all works. If you choose any Kerberos flags
then the YP checks should be bypassed, but that may not be enough.
I'll modify it some more if it turns out I broke something. For now,
support for localand NIS passwords is pretty solid:
- If you simply type 'passwd,' the program checks to see if you exist
in the local pwd.db database. If not, you get bounced to YP.
- If you try to force local functionality with the -l flag and you
don't exist locally, you get an error.
The -y flag can be used to force YP functionality. -f and -s let you
change your full name and shell (respectively). -f *and* -s let you
change all of your 'account information.'
ypchfn, ypchsh, yppasswd and ypchpass are all links to passwd.
You can now specify separate attributes for selected/not selected
cases individually for each field and also an attr for the form as
a whole so you can now have colored backgrounds for the form and
different coloured fields etc.
Update the example.
Change the copyright to a BSD style one.
Include bteasy, bootsd, sdboot and termcap entries using file2.c
Remove all traces of "termcap.small".
The policy in this program regarding termcap is:
| If $TERM is set
| do nothing special, rely on usual termcap.
| else
| use compiled in (via file2c) termcap entries
Now it matches the man page and also the only other commercial implementation
i have found so far ( Solaris 2.x).
Changed the name from ss_base to ss_sp.
It will read a file on stdin and write it as decimal integers on stdout,
this is useful for embedding files in c-sources.
There are a few places where this is needed, and this is a better way than
the current practice of hand-editing the sources.
The command:
date | file2c 'const char date[] = {' ',0};'
will produce:
const char date[] = {
83,97,116,32,74,97,110,32,50,56,32,49,54,58,52,55,58,51,51,32,80,83,84,
32,49,57,57,53,10
,0};
The manual page is 2 lines longer than the source :-)
Display update method changed, now allways write in memory buffer,
then periodically update physical display.
Speed improvements (now > 5 times faster than the old syscons).
History now circular buffer, with changeable size.
History scroll by up/down line, up/down page, home and end.
Backtab proberly implemented.
Now space for 96 function keys, 63 allocated standard, default now
SCO/SYSV compat again as in the old days.
New keyboard definition files ~share/syscons/keymaps/*
Misc fixes for old "hacks" that broke SCO/SYSV compat.
More that I forgot before writing this...
> So, the problem is hostnamebyanyaddr() assumes that _res is already
> initialized to proper values, but this is no longer true as of BIND
> 4.9.3. Here is a patch for sendmail 8.6.9 which changes
> hostnamebyanyaddr() to make sure res_init() has been called before using
> _res.retry.
Submitted by: Matt Day <[email protected]> via Terry Lambert
Handles at least Trantor T130 and ProAudioSpectrum adapters.
The pas driver has consequently been removed.
This driver can be configured without without interrupts.
Manpage to follow when PAS16 has been edited in.
Reviewed by: phk
Submitted by: Serge Vakulenko, <[email protected]>
the version installed from /usr/share. It's hard to eliminate old versions
- few Makefiles have `uninstall' targets and sup/ctm tends to blow away
old Makefiles.
This Makefile needs more work. Stuff is built at install time...
case, software cursor now optional case. Driver must provide
raw things (what hardware do for us, exactly) as default case,
all driver features must be _optional_. Modern VGAs have internal
configuration utilities to set cursor shape/blinking which stored
into cards ROM, and syscons nuke out such features completely
by forcing software cursor. Moreover, software cursor is hard
to distinguish on standouted (or near standouted) fields and
tends to disappearse from the screen.
Set "flags 0x4" to enable software cursor now.
o Cleanup screen savers.
o Don't draw cursor if saver or blinker is active.
o Duplicated code moved to functons.
o Add more checks for blinker in progress, character lost otherwise
when blinker restore old contents.
o Reduce blinking counter to 3, too slow in old variant.
o Fix timeout code in scrn_timer(), old variant can reenter iself,
if action takes too long time.
o Disable visual bell for scroll lock mode, saved screen
becomes overwritted otherwise.
(Boot with the -D flag if you want symbols.)
Make it easier to extend `struct bootinfo' without losing either forwards
or backwards compatibility.
ddb_aout.c:
Get the symbol table from wherever the loader put it.
Nuke db_symtab[SYMTAB_SPACE].
boot.c:
Enable loading of symbols. Align them on a page boundary. Add printfs
about the symbol table sizes.
Pass the memory sizes to the kernel.
Fix initialization of `unit' (it got moved out of the loop).
Fix adding the bss size (it got moved inside an ifdef).
Initialize serial port when RB_SERIAL is toggled on.
Fix comments.
Clean up formatting of recently added code.
io.c:
Clean up formatting of recently added code.
netboot/main.c, machdep.c, wd.c:
Change names of bootinfo fields.
LINT:
Nuke SYMTAB_SPACE.
Fix comment about DODUMP.
Makefile.i386:
Nuke use of dbsym.
Exclude gcc symbols from kernel unless compiling with -g.
Remove unused macro.
Fix comments and formatting.
genassym.c:
Generate defines for some new bootinfo fields. Change names of old ones.
locore.s:
Copy only the valid part of the `struct bootinfo' passed by the loader.
Reserve space for symbol table, if any.
machdep.c:
Check the memory sizes passed by the loader, if any. Don't use them yet.
bootinfo.h:
Add a size field so that we can resolve some mismatches between the loader
bootinfo and the kernel boot info. The version number is not so good for
this because of historical botches and because it's harder to maintain.
Add memory size and symbol table fields. Change the names of everything.
Hacks to save a few bytes:
asm.S, boot.c, boot2.S:
Replace `ouraddr' by `(BOOTSEG << 4)'.
boot.c:
Don't statically initialize `loadflags' to 0. Disable the "REDUNDANT"
code that skips the BIOS variables. Eliminate `total'. Combine some
more printfs.
boot.h, disk.c, io.c, table.c:
Move all statically initialzed data to table.c.
io.c:
Don't put the A20 gate bits in a variable.
There is similar bogusness in the pageout daemon that will be fixed soon.
This fixes a panic pointed out to me by Bruce Evans that occurs when
/dev/mem is used to map managed memory.
Don't initialize CLEANFILES here. Many FONTFILES are sources and required
special clean rules to avoid cleaning.
Makefile.tty:
Initialize CLEANFILES. All tty FONTFILES are objects.
cleanup routine, we don't look at bogus data to determine wheter or not
to free the fields of the hostdata struct. This cures the "klogin segfaults
when no kerberos servers are availible" problem.
in the PCnet/Lance family.
Fix attach so 32 bit cards don't call isa_dmacascade.
Add a workaround for 32 bit chips which incorrectly truncate the
ring buffer size.
Fix a bug where CRC errors were reported as framming errors.
Change copyright to a BSD style one.
Added hook for pmap_prefault() and use symbolic constant for new third
argument to vm_page_alloc() (vm_fault.c, various)
Changed the way that upages and page tables are held. (vm_glue.c)
Fixed architectural flaw in allocating pages at interrupt time that was
introduced with the merged cache changes. (vm_page.c, various)
Adjusted some algorithms to acheive better paging performance and to
accomodate the fix for the architectural flaw mentioned above. (vm_pageout.c)
Fixed pbuf handling problem, changed policy on handling read-behind page.
(vnode_pager.c)
Submitted by: John Dyson
implemented the ability to limit bufferspace by memory consumed. (vfs_bio.c)
Fixed recently introduced bugs that caused extra I/O to happen in some
cases. (vfs_cluster.c)
Submitted by: John Dyson
Moved various pmap 'bit' test/set functions back into real functions; gcc
generates better code at the expense of more of it. (pmap.c)
Fixed a deadlock problem with pv entry allocations (pmap.c)
Added a new, optional function 'pmap_prefault' that does clustered page
table preloading (pmap.c)
Changed the way that page tables are held onto (trap.c).
Submitted by: John Dyson
problems in the process:
1. Quoting should work properly now. In particular, Chet's reported bash
make problem has gone away.
2. A lot of memory that just wasn't being free'd after use is now freed.
This should cause make to take up a LOT less memory when dealing with
archive targets.
3. Give proper credit to Adam de Boor in a number of files.
Obtained from: NetBSD (and Adam de Boor)
This command is required to exist in terms of compatibility with the
Posix 1003.2 specification. It actually invokes the lpr service with
the proper options.
page flipping anytime soon and 4k just wastes memory. Performance via the
looback interface will decrease slightly by this change. Idealy, we need
buffers that can have variable sizes, but this requires a rewrite of far
too much code at the moment.
1) Link against object directory version of libcom_err.so.
2) Don't try to install ss_err.h if we haven't made it yet. It's not
on the critical path for `make world' at this point.
1) Don't clone routes to multicast destinations; there is nothing useful
to be gained in this case.
2) Reduce default expiration timer to one hour. Busy sites will still
likely want to reduce this, but for ordinary users this is a reasonable
value to use.
delete them when the ``parent'' goes away
route.h: add glue to track this to rtentry structure. WARNING WILL ROBINSON!
This will be yet another incompatible change in your route-using binaries.
I apologize, but this was the only way to do it. I took this opportunity
to increase the size of the metrics to what I believe will be the final
length for 2.1, so that when the T/TCP stuff is done, this won't happen
again.
1) Changed LIB_SCCS and SYSLIB_SCCS to LIB_RCS and SYSLIB_RCS.
2) Changed sccsid[] variables to rcsid[]
3) Moved all RCSID strings into .text
4) Converted all SCCSID's to RCS $Id$'s
5) Added missing $Id$'s after copyright.
Print out the length of the compiled sequencer program.
aic7xxx.seq:
More optimizations. Replace generic bcopy routine with bcopy_3
and bcopy_4 (ie unroll the loops) since these are the only two cases used.
Initialize SIMODE1 and SXFRCTL1 from the kernel in ahc_init instead of
at each selection/reselection since this is expensive and only needs to
be done once. Condense function returns into previous instruction if possible.
Reorder some sections to kill superflous jumps. These optimizations kill
the ~150k/s penalty adding support for Twin/Wide cards was costing since
the last place in the commaon path of execution where we had to do ugly,
convoluted testing for the type of card in the sequencer has gone away.
Next stop tagged queuing and target mode.
work (mi_switch() counted the last timeslice again but this didn't affect
the exiting process' rusage because the rusage has already been finalized).
Remove stale comment.
the physical device is closed. Previously only the reverse case was handled.
Abuse the cdevsw interface instead of the vfs interface to do this.
Remove unnecessary #includes.
When using cp to copy a file under the following circumstanes:
- original file in on an NFS filesystem
- destination file is on the same NFS filesystem
- the file is less than 8Mbytes in size
- the file is larger than 65536 bytes in size
the cp process can get frozen in device-wait and never wake up (cp uses
mmap() in this case).
A small change to allocbuf() fixes this.
Obtained from:
bios boot block changed to allow booting from both the attached graphics
display and from a serial port. (A specially compiled serial boot block
is no longer necessary.) The boot block should detect the presence or
absence of a keyboard: if there is no keyboard, COM1 is turned into the
console. This simulates the behavior of the Sun boot PROMs. Unplug your
keyboard, attach a terminal to COM1 and you should be ready to go. :)
Obtained from:
sio.c and sioreg.c changed to allow autodetecting the RB_SERIAL flag
passed by the boot blocks so that the kernel can switch to 'serial
console' mode automagically. 'options COMCONSOLE' can still be specified
to force the kernel to always use the serial port as a console.
CONUNIT and CONADDR can also be specified in the kernel config file
if the user wants to shift the console to a different port.
Obtained from:
Added a new flag (RB_SERIAL) which is passed by the boot block to tell
the kernel that it should use a serial port as a console. (The kernel
can still be forced to boot in serial console mode if 'options COMCONSOLE'
is used.)
Put in the much shorter and cleaner version for the calibrate_cycle_counter
for the Pentium that Bruce suggested. Tested here on my Pentium and
it works okay.
1) It was export-controlled.
2) It used some ad-hoc protocol invented by Berkeley in ignorance of the
standard MIT distribution's way of doing it (which makes it useless
to most people).
This should be fixed once we have `kadmin'/`kadmind'.
YP by disallowing `+' entries as logins in all cases. (This handles the
case of a `+' entry in the password file but YP not running, which should
never happen but is easy enough to check for so we'll apply some
prophylaxis.)
spelled g*compiled* symbols from the kernel so that ddb doesn't have to
do it. The symbols are currently removed by dbsym but dbsym will go
away when symbols are loaded by the boot loader.
Document -m option in usage message.
Check for overrunning some arrays.
Fix some misformatting.
sigreturn() sometimes failed for ordinary returns from signal handlers.
Failures of ordinary returns "can't happen" and are badly handled.
"Temporary" fix: allow users to corrupt PSL_RF. This is fairly
harmless. A correct fix would involve saving the old %eflags (and
perhaps the old segment registers) where the user can't get at them.
/usr/src/share/termcap/termcap.src? It defines the sequences emitted
by the PageUp, PageDown and Keypad-[79513] keys.
Submitted by: Thomas Gellekum <[email protected]>
(original "High Sierra") CD format. I've already implemented this for
1.1.5.1 (and posted to -hackers), but didn't get any response to it.
Perhaps i'm the only one who has such an old CD lying around...
Everything is done empirically, but i had three of them around (from
different vendors), so there's a high probability that i've got it
right. :)
WDTR, and message reject handlers so they don't need to exist in the
sequencer. All three of these cases are not on the critical path, so it
makes little sense to use up precious sequencer ram for them.
(SCSI control block) instead of having the host PIO it down. Also
reimplement WDTR and SDTR optimization to remove code in the sequencer
and place the responsibility of knowing when to initiate SDTR or WDTR
on the kernel driver. This vastly shortens the sequencer program yet
yeilds the same performance.
properly from the beginning:
1) The `kern_devconf' struct should be a part of the driver's
`softc' structure (now it is).
2) The `description' should say what the device actually is,
rather than just giving a model number (now it does).
3) The device should be registered even if the probe fails, so
that it can be reconfigured later.
4) For netifs, the device state should follow the IFF_UP flag.
Other network interfaces should follow this example. (Please?) Eventually
there should be a rundown routine doing the equivalent of setting IFF_UP
off, and perhaps more if warranted.
1) Don't spit out an error message if Kerberos is installed but not yet
set up.
2) Don't attempt to verify the ticket you got back, as workstations
are not intended to have srvtab files of their own.
Both behaviors can be re-enabled with KLOGIN_PARANOID.
a number of (ex-)Athena programs. Breaking my own rules for importing
somewhat, as this code does not appear to be actively maintained by anyone
(not that it really needs it).
share/doc/usd/{30.rogue,31.trek}: make fails if the games source
tree is not present (see the mail that I have sent yesterday).
This patch makes the Makefiles test if the games source
tree is present. If it is not present, the Makefiles default to
no operation.
share/doc/usd/{30.rogue,31.trek}: make fails if the games source
tree is not present (see the mail that I have sent yesterday).
This patch makes the Makefiles test if the games source
tree is present. If it is not present, the Makefiles default to
no operation.
[Note: I'm not sure if the Makefile changes might not be collapsable into
a shorter format, but I'll just leave it this way for now and be safe -jkh]
Submitted by: Remy Card <[email protected]>
when creating the obj link. While bsd.prog.mk inconditionnaly creates
a link in /usr/obj, bsd.doc.mk tests if the source tree is contained in
/usr/src. If so, it creates a link to /usr/obj. If the source tree
is contained in another directory, bsd.doc.mk creates an obj subdirectory.
Submitted by: Remy Card <[email protected]>
a program directory has subdirectories, make now prints "===> dir/subdir"
instead of "===> subdir". This is modeled after the rules contained in
bsd.subdir.mk.
Submitted by: Remy Card <[email protected]>
attempted to check for insecure and fatal eflags and segment
selectors, but missed many cases and got the IOPL check back to
front. The other syscalls didn't check at all.
sys_process.c, machdep.c:
Only allow PT_WRITE_U to write to the registers (ordinary and FP).
psl.h, locore.s, machdep.c:
Eliminate PSL_MBZ, PSL_MBO and PSL_USERCLR. We are not supposed
to assume anything about the reserved bits. Use PSL_USERCHANGE
and PSL_KERNEL instead. Rename PSL_USERSET to PSL_USER.
exception.s:
Define a private label for use by doreti when returning to user
mode fails.
machdep.c:
In syscalls, allow changing only the eflags that can be changed on
486's in user mode (no longer attempt to allow benign IOPL changes;
allow changing the nasty PSL_NT; don't allow changing the i586
bits).
Don't attempt to check all the cases involving invalid selectors
and %eip's. Just check for privilege violations and let the invalid
things cause a trap.
procfs_machdep.c:
Call the ptrace register functions to do all the work for reading
and writing ordinary registers and for single stepping.
trap.c:
Ignore traps caused by PSL_NT being set. Previously, users could
cause a fatal trap in user mode by setting PSL_NT and executing an
iret, and a fatal trap in kernel mode by setting PSL_NT and making
a syscall. PSL_NT was cleared too late and not in enough modes to
fix the problem.
Make all traps in user mode (except T_NMI) nonfatal.
Recover from traps caused by attempting to load invalid user
registers in doreti by restarting the traps so that they appear to
occur in user mode.
---
Fix bogons that I noticed while fixing the above:
psl.h:
Fix some comments.
Uniformize idempotency ifdef.
exception.s, machdep.c:
Remove rsvd[0-14]. rsvd0 hasn't been reserved since the 486 came
out. Replace rsvd0 by `align'. rsvd[0-11] used wrong (magic
non-unique) trap numbers. Replace rsvd[1-14] by rsvd.
locore.s:
Enable alignment check flag on 486's and 586's.
machdep.c:
Use a better type for kstack[].
Use TFREGP() to find the registers.
Reformat ptrace functions from SEF to something closer to KNF.
procfs_machdep.c:
The wrong pointer to the registers got fixed as a side effect.
Implement reading and writing of FP registers.
/proc/*/*regs now work (only) for processes that are in memory.
Clean up comments.
trap.c, trap.h:
Remove unused trap types.
unreachable case label in kdb_trap().
Use the correct case labels in kdb_trap() so that normal ddb entry doesn't
print a message.
Change all printf's to db_printf's. Now you can put a breakpoint at printf,
and ddb entry messages don't spam the syslog output.
Cosmetic:
Use ISPL() instead of magic numbers.
Don't compile the unused function kdb_kbd_trap().
Improve some asms.
Print the arg to Debugger().
need to be moved into the qcollapse and rcollapse routines, but I don't
have time at the moment to make all the required changes...this will do
for now.
sense retrieval code that messed up CDROM devices. This code will also
responde correctly to SDTR and WDTR messages from devices that start a
negotiation sequence.
protected drive at open() time has been *totally bogus*! The guy who
submitted it didn't understand all the implications of calling
set_motor(), and the `who' who included the patch into the tree did it
blindly... Pleeeeze, don't commit code to this driver unless you are
really going to understand what it does! This one caused me to pull
out even more hears, and those who know me do know that i ain't got
too many o'them. :-)
misfeature caused troubles when a program attempted to access a shlib
where one with a higher minor number has been hashed. Ldconfig does
only include the highest-numbered shlib anyway, so this is in no way a
limitation of generality.
Caution: after installing the new programs, your /var/run/ld.so.hints
needs to be rebuiult; run ldconfig again as it's done from /etc/rc.
1) Firewall is not subdivided on forwarding / blocking chains
anymore.Actually only one chain left-it was the blocking one.
2) LKM support.ip_fwdef.c is function pointers definition and
goes into kernel along with all INET stuff.
firewall should *NOT* be compiled into kernel.
Then it can be loaded.This is misc module but i'v
got no problemms with it,so shouldn't you i suppose..
BTW this is very stupid to have one module in CVS
for ALL lkm's...
We have only one firewall chain and one accounting chain now.
No blocking/forwarding so commands changed.
Man pages are somewhat out of date and will be updated ASAP.
No kernel config options anymore besides keyboard language layout.
Virtual consoles are now dynamically allocated, no NCONS anymore.
Software cursor blinking/nonblinking.
Visual bell for laptops (don't beep at meetings :-).
Cursor/bell default type setable via config "flags" instead of as defines.
Cursor/bell type setable via ioctl's.
New video modes 80x30 80x60 for some laptops, and those with multisync monitors.
Scroll-lock history (length currently fixed at 100 lines).
Lots of cleanups, some only commented out for now (will goaway soon).
Support for new features in vidcontrol/kbdcontrol.
Updated manpages.
being cleared in some cases for vnode backed objects; we now do this in
vnode_pager_alloc proper to guarantee it. Also be more careful in the
rcollapse code about messing with busy/bmapped pages.
now marked busy as long as it's being in non-reset state, and the
drives are busy as long as at least one instance is open.
Also reformat everything to fit into 80 columns again.
Changed my mind wrt. error reporting for a write-protected drive and
an open() with write intent; ENXIO has been too weird, now return EIO.
Some portions of the code need to be rewritten to use tprintf()
instead of simple printf()'s, so the messages will also appear on the
session terminal, however.
input forms. It has the following simple fields:
Text fields: Just titles, labels etc.
Input fields: An editable text field that may or may not have an
initial default value.
Labelled input field: This is an input field that has an initial
informative entry in it but it vanishes when you start editing the
field.
Toggle fields: These are fields with a pre-defined list of options
which you cycle through using the space bar.
Action fields: These are button type fields that call functions when
they are selected.
A simple demo is included in examples.
Wangtek PC-02 QIC-02 controller with Cipher 150MB tape drive
Any attemp to open /dev/rwt0 hangs.
The following patch to /sys/i386/isa/wt.c is derived from Mikael
Hybsch's wt driver.
Submitted by: Terry Lee <[email protected]>
perl setuid scripts don't work in 2.1-current for the same reason they were
not working in 1.1.5.1.
Perl 5 has the same "problem" of course.
We have almost POSIX saved uids but we must undefine the following symbols
in order to get setuid perl scripts :
Submitted by: [email protected] (Ollivier Robert)
much higher filesystem I/O performance, and much better paging performance. It
represents the culmination of over 6 months of R&D.
The majority of the merged VM/cache work is by John Dyson.
The following highlights the most significant changes. Additionally, there are
(mostly minor) changes to the various filesystem modules (nfs, msdosfs, etc) to
support the new VM/buffer scheme.
vfs_bio.c:
Significant rewrite of most of vfs_bio to support the merged VM buffer cache
scheme. The scheme is almost fully compatible with the old filesystem
interface. Significant improvement in the number of opportunities for write
clustering.
vfs_cluster.c, vfs_subr.c
Upgrade and performance enhancements in vfs layer code to support merged
VM/buffer cache. Fixup of vfs_cluster to eliminate the bogus pagemove stuff.
vm_object.c:
Yet more improvements in the collapse code. Elimination of some windows that
can cause list corruption.
vm_pageout.c:
Fixed it, it really works better now. Somehow in 2.0, some "enhancements"
broke the code. This code has been reworked from the ground-up.
vm_fault.c, vm_page.c, pmap.c, vm_object.c
Support for small-block filesystems with merged VM/buffer cache scheme.
pmap.c vm_map.c
Dynamic kernel VM size, now we dont have to pre-allocate excessive numbers of
kernel PTs.
vm_glue.c
Much simpler and more effective swapping code. No more gratuitous swapping.
proc.h
Fixed the problem that the p_lock flag was not being cleared on a fork.
swap_pager.c, vnode_pager.c
Removal of old vfs_bio cruft to support the past pseudo-coherency. Now the
code doesn't need it anymore.
machdep.c
Changes to better support the parameter values for the merged VM/buffer cache
scheme.
machdep.c, kern_exec.c, vm_glue.c
Implemented a seperate submap for temporary exec string space and another one
to contain process upages. This eliminates all map fragmentation problems
that previously existed.
ffs_inode.c, ufs_inode.c, ufs_readwrite.c
Changes for merged VM/buffer cache. Add "bypass" support for sneaking in on
busy buffers.
Submitted by: John Dyson and David Greenman
needed and the file wasn't closed when the -t option was used.
Originally by [email protected], but were incomplete.
Submitted by: [email protected] and myself
my mailbox since early last year. Fixes a problem with running out of
fds (by hitting the limit or whatever) when ar is given a long list of
objects. The fix was to add a missing close().
Submitted by: Robert Crowe <[email protected]>
Reenabled "SCIOCOMAND" ioctl.
Restructured so low level drivers can easily request retries.
Added preliminary fixed SCSI devices (should be revisited before 2.1)
Added "ssc" device that can have its' (HBA, ID, LUN) set via ioctl.
shifting. Also correct the original code as Garrett noticed it in mail.
Leave the mishandled code in to use it later if future versions of gcc
are correct. The code was part of the calibrate_cyclecounter routine to
get the speed of the pentium chip.
floppy driver (or in the hardware?). It turned out to be caused by
spurious interrupts, right after an FDC reset.
Also major cleanup in the low-level structure, there are now functions
performing error-checks for the FDC I/O.
Submitted by: (mostly) Peter Dufault <[email protected]>
It used to do this by setting a global <Yuck>. Now we set th VNINACT
flag in the vnode to force a skip of ufs_inactive.
Sorry for missing this file in my last commit folks.
Index: vnode.h
===================================================================
RCS file: /usr/cvs/src/sys/sys/vnode.h,v
retrieving revision 1.14
diff -c -r1.14 vnode.h
*** 1.14 1994/11/14 13:51:53
--- vnode.h 1994/12/03 01:06:27
***************
*** 116,121 ****
--- 116,122 ----
#define VALIASED 0x0800 /* vnode has an alias */
#define VDIROP 0x1000 /* LFS: vnode is involved in a directory op */
#define VVMIO 0x2000 /* VMIO flag */
+ #define VNINACT 0x4000 /* LFS: skip ufs_inactive() in lfs_vunref */
/*
* Vnode attributes. A field value of VNOVAL represents a field whose value
safe way to do this, and envites very unpleasant results. Removed fsck'ing
of all the disks on the system as it provides output that is almost always
meaningless and only envites bug reports.
Reviewed by: Jordan Hubbard
Index descriptions are limited to MAXINDEXSIZE (60) chars. Any description
beyond that is truncated. Also, only the first line is displayed as well.
This allows pkg_info -a -I to be formated in two columns with one line
per package for easy reading.
Reviewed by: jkh
ordering that can prove fatal during large batches of deletes, but this
is much better than it was. I probably won't be putting much more time
into this until Seltzer releases her new version of LFS which has
fragment support. This should be availible just before USENIX.
no more DOS boots to start it up.
Simply did a localized nuke of the OUTB macro in this file. This is
a kludge, since it seems it may actually be necessary in other GUS
files (tbd).
Thanks to: Amancio Hasty & Ken Hornstein
correct console number for the VT_WAITACTIVE ioctl. Invalid console numbers
caused waiting on an invalid pointer.
Use bcopyw() instead of move_up() and move_down(). bcopyw() handles
overlapped copies and should be faster. Actually use bcopy(). bcopy()
is slightly faster if video memory is 16-bit and about twice as fast if
it is 32-bit. bcopy() is said to fail on someGA's, but syscons already
depends on it working for other accesses to video memory.
If nd->swap_nblks is zero in nfs_mountroot(), then the system
comes up without initializing swapdev_vp to an actual vnode pointer.
The swap pager assumes a non-NULL value for swapdev_vp.
The fix is to try initializing local swap if no NFS swap space
is specified.
Remove bogus input operands for fnsave(), fnstcw() and fnstsw().
Change all fwait's to fnop's. This might help avoid hardware bugs.
Wait after fninit with an fnop. This should be safer now.
Fix some spelling and formatting errors.
Use natural sizes for control and status words (u_short, promotes to int).
Don't clobber the SWI_CLOCK_MASK bits in npx0_imask when using IRQ13.
Set the devconf state correctly (always busy, if configured). Improve
code for npx_registerdev() a little (gcc can't keep id->id_unit in a
register for some reason). Don't register a nonexistent npx device.
Print a useful message in npxattach() again (delete references to errors
and not the whole message). Don't print "387 emulator" if there is no
emulator in the kernel.
Use %p for pointers in error messages.
Don't clobber the FPU state when there is an FPU exception. Just clear
the exception flags (after saving the flags as before). This allows
debuggers and SIGFPE handlers to look at the full exception state.
SIGFPE handlers should normally return via longjmp(), which restores a
good FPU state (as before). Returning from a SIGFPE handler may leave
the FPU in the wrong state (as before).
Clear the busy latch _after_ clearing the exception flags so that there
is less chance of getting a bogus h/w interrupt for a control operation.
Clear the saved exception status word when the next FPU instruction is
excuted so that it doesn't stick around until the next exception.
Clear the busy latch after fnsave() in npxsave() in case it was set when
npxsave() was called.
Fixes bugs in the latter: the `all' target was never up to date; there
was no `depend' target. Doesn't work for multiple info files because
it leverages bsd.doc.mk and that is broken. Info should be installed
more like man pages...
Updated to 2.0 .
Included sections about how to use DDB, post-mortem analysis of
a kernel crash where you didn't anticipate it and therefore
didn't config -g it. Added a real-world example of a kgdb session.
values for syncronous negotiation. The 284x series adaptors can now be
supported without the Bios being enabled. If you disable the Bios on the
274x series adaptors, all configuration parameters revert to the default
since there is no way to retrieve them.
You can now sling 14 devices off of a 274xT. In the process of adding
twin channel support, I removed all evident restrictions on supporting
Wide channeled devices, but I do not have a Wide controller to test them
on.
aic7770_seq.h, the pre-compiled header, is no longer needed since config
handles this dependancy.
- /sys/i386/i386/swapgeneric.c is just plain broke. But fear not, for I
have unbroken it. One thing that swapgeneric.c does is walk through the
list of configured devices searching for a boot device. The only easy
way to accomplish this in 2.0 is to use Garret Wollman's kern_devconf
stuff. *BUT*, the head of the kern_devconf linked list (dc_list) is declared
static in /sys/kern/kern_devconf.c. This means that swapgeneric.c can't
see it at link time. I had to remove the 'static' keyword to get around
this little problem. I hope this doesn't break anything anywhere.
*Furthermore,* there's a small matter of making the call to setconf()
in swapgeneric.c disappear when 'config kernel swap generic' isn't used.
You could change /sbin/config to create a dummy setconf() function in
swapkernel.c, but that seems messy somehow. (It's also someting of an
'it isn't broken, why are you fixing it' situation.) My solution was to
do what the NetBSD people did and put an #ifdef GENERIC around the call
to setconf(). If your kernel is called GENERIC or you define 'options
GENERIC,' then you can use 'config kernel swap generic' and it'll work.
That aside, the upshot is that: a) swapgeneric.c actually works, and
and b) the -a boot flag now works as well. If you boot with -a, as in
"Boot: wd(0,a)/kernel -a" you will be presented with a 'root device?'
prompt after the autoconfig phase, at which point you can specify what
device you want mounted as root. Regrettably, you can't specify an NFS
filesystem. Yet. Three files are affected: /sys/i386/i386/swapgeneric.c,
/sys/i386/i386/autoconf.c and /sys/kern/kern_devconf.c.
Submitted by: wpaul
- /sys/i386/isa/if_ed.c doesn't quite know how to deal with SMC EtherEZ
ethernet cards. The EtherEZ looks just like the Elite Ultra, except it
has only 8K of shared memory. The only way to have it properly detected
is to zero and test a few bytes of memory just about the first 8K region.
If it clears properly, it's an Elite Ultra, otherwise it's an EtherEZ.
I've also got an EtherEZ patch for netboot (Makefile, ether.c and ether.h).
- /sys/i386/isa/syscons.c wraps at the next to the last column rather than
the last column, like it should. You don't really notice this unless you
use certain programs that write all the way out to, say, the 80th column,
like VMSmail. Along with a one-line fix for this are some changes to
implement a non-blinking cursor. Put 'options "NOBLINK_CURSOR"' in your
config file and give it a try. :)
Submitted by: wpaul
This might be useful for debugging applications that use a special LDT.
However, printing of all segment registers is currently broken.
Don't print "last exception: " before the FPU opcode and pc, etc. The
opcode and pc, etc., are for the last FPU _instruction_.
Pass the saved exception status word to print_387_status() so that the
exception(s) that caused or will cause a trap can be seen. The kernel
has supported this since 1.1 or before. The kernel still clobbers the
tag word if a trap occurs.
Remove unused null function clear_regs().
cvs is not being used effectively for gdb. Our old changes get clobbered
and our new changes are mixed with "vendor" changes in the same updates
so they will be difficult to untangle for the next release of gdb. The
revision logs get spammed for each release of gdb.
Would you please commit this two-line patch to /sys/i386/isa/b004.c
(the Transputer driver) so that it at least compiles under 2.x
Haven't tried if the driver is working properly, but a kernel with
compiled-in driver has been running for two days now with no apparent
problems.
Submitted by: luigi
This is new version of Seagate ST01/02, Future Domain TMC-885, TMC-950
SCSI driver for FreeBSD. I started from the 2.0R version and mostly
rewrote it. New features are:
1) New probe algorithm. Old driver read the BIOS region of the adapter
memory and find the copyright string. The problem was in the BIOS itself:
it conflicted with IDE disks. The solution was to unplug it and
make the probe algorithm to work without it.
2) Proper timeout handling in numerous places where the driver
polls waiting for some event.
3) Assembler flagments added in critical places, mostly for data transfer
to of from the target. It was possible to make it faster,
but at the price of decreasing reliability.
4) Target-dependent delays when waiting for REQ deassert event.
Some devices seem to be slower (CD-ROMS, some tape drives),
and some seem to be too fast (disks). The driver tests the REQ
deassert timeout for each target and then uses it for polling.
5) Device flags added for SCSI parity control and sense request
priority control.
6) Generic cleanup, after which the driver became much more readable
(at least by me:).
7) Target data parity error logging is limited to avoid log file overflow.
8) Manual page added.
Submitted by: serge
the wild, slippery orgy commence!
Gary Jennejohn, too studly for his own good, has finally come through with
the new, improved gdb 4.13. This gdb features:
o kgdb support - if this works (and I urge folks to test it), we can
finally purge the old and hateful version of kgdb from our source
tree.
o attach/detach support. See comments in README.FreeBSD for more
details.
o Well, it's newer. Our previous version was 4.11.
Comments and flames to gj, of course! :-)
Thanks, Gary. Much appreciated. The previous state of gdb/kgdb has been a
thorn in all of our sides for some time..
Submitted by: gj
- The -a flag now works just as it does in SunOS: '-a' is actually
handled like a wildcard for all interfaces. 'ifconfig -a' displays
the status of all interfaces, 'ifconfig -a netmask 0xffffff00' sets
the netmask of all interfaces, and so forth. I don't know if many
people really need to be able to set the netmasks of all interfaces
at once, but the SunOS ifconfig seems to allow this, so there you
have it.
- An 'ether_status' function has been added to display the ethernet
address of all ethernet interfaces. Again, as in SunOS, you must
be root in order for this to work. The ethernet address is read
from /dev/kmem using kvm_open() and kvm_read(), much in the same
was as it's done with netstat. If you choose to install ifconfig
set-gid kmem then normal users will be able to see the ethernet
address as well, though this may not be desireable. This feature
requires a small change to the ifconfig Makefile: you need to link
with -lkvm in order to use the kvm_*() functions.
Submitted by: wpaul
stat the pathname "" in order to decide that the pathname "/" is
a directory. This caused `cp kernel /' to fail if the kernel has
the POSIX behaviour of not allowing the pathname "" to be an alias
for ".". It presumably also caused `cp /etc/motd /' to fail in
the unlikely event that "." is not stat'able.
Be more careful about concatenating pathnames: don't check that
the pathname fits until prefixes have been discarded (the check
was too strict). Print the final pathname in error messages.
Terminate the target directory name properly for error messages.
Don't add a slash between components if there is already a slash.
Move definition of `stat_imask' to clock.c.
clock.c:
Rename `rtcmask' to `stat_imask' and export it. Rename `clkmask' to
`clk_imask' for consistency.
Only calculate TIMER_DIV(hz) once.
Merge debugging and "garbage" code to produce debugging code and format the
output better.
Make writertc() static inline and use it everywhere. Now all accesses to
the clock registers go through rtcin() and writertc().
Move rtc initialization to cpu_initclocks().
Merge enablertclock() with cpu_initclocks() and remove enablertclock().
The extra entry point was just a leftover from 1.1.5.
Bogus pstat usage message from pstat:
usage: pstat -Tfnstv [system] [-M core] [-N system]
[system] is not mentioned in the man page and I don't
see where it is used in the code either.
Added also a [] around the first options to show them as optional, ATS.
timestamps for an atomic operation such as rename() on a local file
system to be identical.
Uniformize yet another idempotency ifdef. The comment nesting was
bogus.
Embalm. Rewrite to do things much the same as gcc-2: use fistpq for speed
and elegance, and mishandle overflow consistently. __fixunsdfsi() is no
longer called by gcc.
of attributes so that `cp -p' to an msdos file system can succeed under
favourable circumstances (no uid or gid changes and no nonzero flags
except SF_ARCHIVED).
msdosfs_vnops.c:
The in-core inode flags were confused with the on-disk inode flags, so
chflags() clobbered the lock flag and caused a panic.
denode.h, msdosfs_denode.c, msdosfs_vnops.c:
Support the msdosfs archive attibute (ATTR_ARCHIVE) by mapping it to
the complement of the SF_ARCHIVED flag and setting the ATTR_ARCHIVE
bit when a file's modification time is set (but not when a file's
permissions are set; this is the standard wrong DOS behaviour).
denode.h, msdosfs_denode.c:
Remove the DE_UPDAT() macro. It was only used once, and the corresponding
macro in ufs has already been removed.
denode.h:
Don't change the timestamp for directories in DE_TIMES() (be consistent
with deupdat()).
msdosfs_vnops.c:
Handle chown() better: return EPERM instead of EINVAL if there are
insufficient permissions; otherwise, allow null changes.
to be padded to 8 chars. Simply make sure that never more than 8 chars
are printed ( %-.8s ). The former commit otherwise hosed the width
calculation and landed on different positions for the time output.
Also the strlen(xx_out_line) hoses the wide
calculation, so that it sometimes make it much larger than necessary.
Simply use always 8 chars for the out_line calculation now. Looks good
this way.
Fix several bugs involving the obsolescent -d and -t options:
-d 0 and -t 0 were ignored
-t -600 was a usage error
-d 'atoi is not suitable for parsing args' and -t duh were not usage errors
Change some error messages to say which call to settimeofday failed.
Restore casts of NULL in function calls.
Finish conversion to using err() instead of perror().
for wd (they both count the number of sectors). The wpms stat is still
moderately bogus for all drivers. Even the count stat could be handled
better (partial blocks should be counted as full blocks; should errors
and retries be counted?).
Fix single-stepping of emulated FPU instructions.
Don't panic if an FPU instruction is attempted but there is no FPU
and no FPU emulator is configured.
v1.9.0 - December 22, 1994. The program won't exit from the interactive shell
if it's working from a tty. For example, it won't exit if you do an mget
on a pattern that won't match anything. Added padding around jmp_buf's
for SunOS. SunOS needs sigjmp_buf's, but plenty of OS's don't support
sigjmp_buf's yet. Fixed the tips to reflect the new archive site.
v1.8.9 - December 20, 1994. Can now set "passive" user variable, or use
passive command to toggle PASV/PORT ftp. Debug mode now prints remote
responses. Can now get around buggy FTP servers like boombox.micro.umn.edu,
that give back invalid port numbers to PASV.
v1.8.8 - December 19, 1994. Now falls back to port FTP if passive FTP fails.
warning handling and allows for link-time warnings with a modified
version of gas.
Note: Not all of the newer bits were updated such as some of the non-x86
machine-dependant code is relevant to FreeBSD right now.
Obtained from: NetBSD
boot(). This is needed so the "serialboot" stuff can share this file,
too.
Everything is #ifdef'ed so it evaluates to nothing when actually been
built in the "biosboot" directory.
The files in this directory are modified version of "biosboot". The
only difference is in that they perform their I/O via a serial port,
so their preferrable usage is to form bootblocks for systems where the
kernel happens to have an "options COMCONSOLE". Most of the code is
actually shared with "biosboot", and make will not (and should not)
descend into this directory by default. It is in the responsibility
of the user to build these bootblocks instead of the original ones.
short, it gets filled uop to its length. This matches the getdomainname
and gethostname manual pages.
(getbootfile also uses this function and I think it should have the same
behaviour)
This also fixes a bug with keyinit where the seed was not saved in
/etc/skeykeys. So S/Key should be fully functional again.
Reviewed by:
Submitted by:
Obtained from:
is supposed to work except "media removal" (shutting down the vn driver)
while some partitions are open.
Fix some errnos: return ENOTTY, not ENXIO for unknown ioctls; return
ENODEV, not ENXIO for the unsupported dump operation.
the APM-bios.
This stabilizes a couple of APM bioses quite a bit.
They all make the mistake of going into 16-bit mode, without clearing the
top half of the 32bit registers.
Later they do a
| movw %si,$0x7331
| movw %ax,0x6(%si)
or something along those lines and crash and burn, because their segment
is already relocated, so adding 0xf0171ce9 to the base of it is bad news.
At least SystemSoft is guilty of this bummer.
Voxware hackers should feel free to work on this some more, it's by no means
a perfect product.
(I have patches for GUS users running 2.x to run their GUS with bidirectional
DMA (talk while listening. All other soundboards must use push-to-talk until
people learn to build real hardware).
Submitted by: amancio hasty & paul traina
and one set by the protocol family. Also add another parameter to
rtalloc1() to allow for any interface flags to be ignored; currently
this is only useful for RTF_PRCLONING. Get rid of rt_prflags and re-unite
with rt_flags. Add T/TCP ``route metrics''.
NB: YOU MUST RECOMPILE `route' AND OTHER RELATED PROGRAMS AS A RESULT OF
THIS CHANGE.
This also adds a new interface parameter, `ifi_physical', which will
eventually replace IFF_ALTPHYS as the mechanism for specifying the
particular physical connection desired on a multiple-connection card.
NB: YOU MUST RECOMPILE `ifconfig' AND OTHER RELATED PROGRAMS AS A RESULT OF
THIS CHANGE.
DE_UPDATE was confused with DE_MODIFIED in some places (they do have
confusing names). Handle them exactly the same as IN_UPDATE and
IN_MODIFIED. This fixes chmod() and chown() clobbering the mtime
and other bugs.
DE_MODIFIED was set but not used.
Parenthesize macro args.
DE_TIMES() now takes a timeval arg instead of a timespec arg. It was
stupid to use a macro for speed and do unused conversions to prepare
for the macro.
Restore the left shifting of the DOS seconds count by 1. It got
lost among the shifts for the bitfields, so DOS seconds counts
appeared to range from 0 to 29 seconds (step 1) instead of 0 to 58
seconds (step 2).
Actually use the passed-in mtime in deupdat() as documented so that
utimes() works.
Change `extern __inline's to `static inline's so that msdosfs_fat.o
can be linked when it is compiled without -O.
Remove faking of directory mtimes to always be the current time. It's
more surprising for directory mtimes to change when you read the
directories than for them not to change when you write the directories.
This should be controlled by a mount-time option if at all.
Improve hzto():
Round up instead of down and then add 1 tick. This fixes sleep(1)
sometimes sleeping for < 1 second and usleep(10000) sometimes sleeping
for as little as 1 usec + syscall time.
Don't do all the calculations at splhigh().
Don't depend on `tick' being a multiple of 1000.
Don't lose accuracy for `sec' between 0x7fffffff / 1000 - 1000 and
0x7fffffff / hz.
Don't assume that longs are 32 bits or that ints have the same size as
longs.
getcwd() has two off-by-one bugs in FreeBSD-2.0:
1. getcwd(buf, size) fails when the size is just large enough.
2. getcwd(buf + 1, 1) incorrectly succeeds when the current directory
is "/". buf[0] and buf[2] are clobbered.
(I modified Bruce's original patch to return the proper error code
[ERANGE] in the case of #2, but otherwise... -DG)
This program demonstrates the bug:
---
#include <stdlib.h>
#include <string.h>
#include <stdio.h>
#include <unistd.h>
int main(void)
{
char buf[5];
int errors;
errors = 0;
if (chdir("/tmp") != 0) {
perror("chdir");
abort();
}
if (getcwd(buf, 5) == NULL) {
perror("oops, getcwd failed for buffer size = size required");
++errors;
}
if (chdir("/") != 0) {
perror("chdir");
abort();
}
buf[0] = 0;
buf[2] = 1;
if (getcwd(buf + 1, 1) != NULL) {
fprintf(stderr,
"oops, getcwd succeeded for buffer size = one too small\n");
++errors;
}
if (buf[0] != 0) {
fprintf(stderr,
"oops, getcwd scribbled on memory before start of buffer\n");
++errors;
}
if (buf[2] != 1) {
fprintf(stderr,
"oops, getcwd scribbled on memory after end of buffer\n");
++errors;
}
exit(errors == 0 ? 0 : 1);
}
pointer returned by realloc(). All callers free the pointer if the
execve fails. Nuke the caching. This essentially restores buildargv()
to the 1.1.5 version. Also fix a memory leak if realloc() fails. Also
nuke similar but non-broken caching in execvp(). malloc() should be
efficient enough.
Prepare for disk slices - more macros for handling disk device numbers,
version of readdisklabel() without DOS goop.
Clean up prototypes.
Uniformize idempotency ifdef.
diskslice.h:
New file.
dkbad.h:
Define more magic numbers.
Declare internalized version of dkbad struct and functions to operate on it.
Uniformize idempotency ifdef.
command available yet.
Changed an entry in getprcent.3 from rpcinfo(8C) to rpcinfo(8).
Changed an entry in getrpcport.3 from 3R to 3.
Changed two entries in rpc.3 from 3N to 3.
worked in the past only because of good fortune. Anyway, use the contig alloc
routine I wrote awhile ago (vm_page_alloc_contig) for the sound code to do
this allocation. Also, specify read+write on the permissions to pmap_enter().
Specifying just read can have unexpected consquences.
2) Change INSTALL_MANPAGES to NO_INSTALL_MANPAGES and document it
3) Add a PKGNAME variable to allow the package name
not to be dictated by stupid DISTNAMEs
4) Add a PATCH_DEBUG option and a slight change to the default
patch system - add --forward to help ensure correct patching
of returning EINVAL since something may depend on them being broken.
Allowing negative limits caused bugs almost everywhere. The recent
fixes for MAXSSIZ checked the limits too late to stop anyone defeating
limits set by root...
match all the port names.
Start using shell functions to avoid duplication.
Make tty* independent of cua*. Restore support for old names (tty0 ==
ttyd0, cua0 = cuaa0...).
Restore making of lpt1 and lpt2 by default.
Keep umask 077 for making vty*. World-ioctable vtys are huge security holes
because of bugs in syscons.
Make vga if a vty is made. It may still be required for X. It got nuked
with pc*.
Start using umask consistently to avoid using chmod.
Added note about lp TCP/IP driver
Added notes about b004, cx, ctx and pcaudio
Updated perl entry to point to ftp site that has it
NOTE: If you have a system running 2.0 please email me ([email protected])
tell what you have so I can include it!
Here's something that should be a big selling point for European users.
Note that Linux still doesn't support anything other than the POSIX locale.
This is a superset of the POSIX locale with support for all the accented
characters. You need this to do compose processing in XFree86 3.x. I'm
using this on my 1.1.5.1 system. Don't know whether it works on 2.0, but
can't think of any reason why it wouldn't.
Submitted by: kaleb
<string.h> isn't supposed to be used by the kernel.
cronix.h is <machine/cronix.h>, not "cronyx.h" (ambiguous) or
<sys/cronyx.h> (nonexistent; caused compile to fail).
cxreg.h is <i386/isa/cxreg.h>, not "cxreg.h".
<i386/isa/cpufunc.h> shouldn't be included directly; it is always
included by <sys/systm.h>.
<i386/include/*.h> is <machine/*.h>
<systm.h> is <sys/systm.h>.
<kernel.h> is <sys/kernel.h>.
<bpfilter.h> is "bpfilter.h". It really is in the current directory.
>Description:
If a process attempts to open a floppy tape device when the
device has been configured in the kernel, but did not probe and attach
on bootup, then a panic will occur.
[Review: The current ft situation is a crock, and this only bandaids
an earlier wound inflicted by making the attach conditional. This urgently
requires a review]
Submitted by: gene
Change a round to a truncate. Problem reported from Christoph Kukulies:
9.8 2 / p did an IOT trap.
There is one remaining problem.: 9.8 2 % p shows on other machines 1.8
but does here in the moment 1.
file anymore after this. My link makes it too painful to make
interactive mods, and I don't have the CVS tree here so making changes
for "previous history" have to get done on freefall, with the corresponding
degree of pain.
Use the correct value of hz (stathz if it is nonzero) for
interpretion of dk_time[] and cp_time[] in iostat.c. Avoid
multiple conversions of this value in iostat.c and vmstat.c
iostat.c:
Implement the display of cp_time[CP_INTR]. Fix the display
of cp_time[CP_IDLE] (the display was always null because
cp_time[CP_INTR] == 0 was displayed instead).
systat.1:
Document the display of cp_time[CP_INTR].
vmstat.c:
Implement the display of cp_time[CP_INTR].
Keep track of interrupt nesting level. It is normally 0
for syscalls and traps, but is fudged to 1 for their exit
processing in case they metamorphose into an interrupt
handler.
i386/genassym.c;
Remove support for the obsolete pcb_iml and pcb_cmap2.
Add support for pcb_inl.
i386/swtch.s:
Fudge the interrupt nesting level across context switches and in
the idle loop so that the work for preemptive context switches
gets counted as interrupt time, the work for voluntary context
switches gets counted mostly as system time (the part when
curproc == 0 gets counted as interrupt time), and only truly idle
time gets counted as idle time.
Remove obsolete support (commented out and otherwise) for pcb_iml.
Load curpcb just before curproc instead of just after so that
curpcb is always valid if curproc is. A few more changes like
this may fix tracing through context switches.
Remove obsolete function swtch_to_inactive().
include/cpu.h:
Use the new interrupt nesting level variable to implement a
non-fake CLF_INTR() so that accounting for the interrupt state
works.
You can use top, iostat or (best) an up to date systat to see
interrupt overheads. I see the expected huge interrupt overheads
for ISA devices (on a 486DX/33, about 55% for an IDE drive
transferring 1250K/sec and the same for a WD8013EBT network card
transferring 1100K/sec). The huge interrupt overheads for serial
devices are unfortunately normally invisible.
include/pcb.h:
Remove the obsolete pcb_iml and pcb_cmap2. Replace them by
padding to preserve binary compatibility.
Use part of the new padding for pcb_inl.
isa/icu.s:
isa/vector.s:
Keep track of interrupt nesting level.
|Message-Id: <[email protected]>
|To: [email protected]
|Subject: A little problem with MAKEDEV
|
|For a while now, MAKEDEV's been kinda neat: you create the cua* files,
|and it deletes the tty* files; you create the tty* files and it
|deletes the corresponding cua* files. K00l! :-)
[Ed Note - I think this behavior was wrong, and this fix better].
incredibly obnoxious, but also makes inverse mappings work when the local
resolver is in a cache-only configuration. (Maybe this is actually
a bug in BIND?)
used as an address value. Then all comparisons should be done unsigned
and not signed. Fix it with a typecast of u_quad_t.
Error can be demonstrated with the current bash in port, do a
ulimit -s unlimited and the machine hangs. bash delivers through
an internal error a large negative value for the stacksize, the
comparison saw this smaller than MAXSSIZ and then tried to expand
the stack to this size.
Now floppy tape support is *disabled* unless you specifically
request otherwise. Poul wanted it this way, and I guess I'm not going to argue
though it may seem counter-intuitive. We can always change it back, later.
make the sequencer code fully compatible with the aic7870 (ie 294x adaptors).
I've also added to my local mods putting the sequencer into "FASTMODE" clock.
This gives upwards of 2M/sec write preformance improvement in some scenarios.
There haven't been any reports of this causing problems, and I have been
reaping the benifits of it for more than a week now.
This also includes a new version of the pre-generated file <ugh>
Obtained from: John Aycock ([email protected]) and myself
determine whether a connection to a given machine is up or not.
In FreeBSD 2.0 (and therefore, I assume, BSD 4.4) the exit code of ping
is always zero, even if no packets were received.
I would like to propose the following change to /usr/src/sbin/ping/ping.c
to restore this useful behaviour:
Submitted by: Denis Fortin
flags & 0x1. Somebody should build a kernel with this and see if
the floppy-tape damaged people can turn it off properly with userconfig.
I can't reproduce the original problem here.
This should have been disabled for some time, but I had screwed up ...
This made spurious values appear for fd0 in systat, when there was
NCR SCSI activity.
comconsole will behave as expected. The true problem should be fixed
instead, Bruce' comment for this:
>Anyway, i found the reason for my problems: somehow, ICRNL isn't in
>effect at `userconfig' time (but only for comconsole?), hence only
ICRNL doesn't apply to cngetc(). cnputc() unconditionally does the
equivalent of ONLCR; perhaps cngetc() should unconditionally do the
equivalent of ICRNL. Ddb must be checking for CR. Userconfig only
checks for NL. Userconfig works with syscons because pccngetc()
does the conversion. This is probably the wrong place to do it.
Allow chown() to return success if the gid isn't changed even if
the gid is not the caller's. Such gids are normal for files created
in world-writable directories sucj as /tmp. This "fixes" annoying
error messages for mv'ing files created in /tmp to another file
system. mv still preserves the foreign gid of /tmp, but now does
it silently.
operation of each clist. Limit the growth of each clist. Clists
can only grow larger than the reserved minimum if there are free
cblocks in a shared pool. The size of this pool is now fixed
(this could be improved). The reserved and maximum sizes are more
carefully allocated for slip and ppp, depending on the mtu. A maximum
MTU of 16384 is now enforced for ppp.
pointer if len is 0. I should have looked at the revision history - I would
have found that Bruce already fixed the bug with len=0 over a month ago.
Whoever said that the bug was in 2.0 was wrong.
1. The pageout daemon used to block under certain
circumstances, and we needed to add new functionality
that would cause the pageout daemon to block more often.
Now, the pageout daemon mostly just gets rid of pages
and kills processes when the system is out of swap.
The swapping, rss limiting and object cache trimming
have been folded into a new daemon called "vmdaemon".
This new daemon does things that need to be done for
the VM system, but can block. For example, if the
vmdaemon blocks for memory, the pageout daemon
can take care of it. If the pageout daemon had
blocked for memory, it was difficult to handle
the situation correctly (and in some cases, was
impossible).
2. The collapse problem has now been entirely fixed.
It now appears to be impossible to accumulate unnecessary
vm objects. The object collapsing now occurs when ref counts
drop to one (where it is more likely to be more simple anyway
because less pages would be out on disk.) The original
fixes were incomplete in that pathological circumstances
could still be contrived to cause uncontrolled growth
of swap. Also, the old code still, under steady state
conditions, used more swap space than necessary. When
using the new code, users will generally notice a
significant decrease in swap space usage, and theoretically,
the system should be leaving fewer unused pages around
competing for memory.
Submitted by: John Dyson
and into ether_input(). It was silly to have bpf want this one way and
ether_input want it another way. Ripped out trailer support from the few
remaining drivers that still had it.
1) make #includes correct
2) fix bugs in address check macros
3) fixed bugs in, and enabled, recopy if heavily fragmented code
4) moved call to bpf tap to be before enqueing packet (probably gratuitous)
5) fixed bug that caused "abnormal interrupt" at boot time/first use
6) added support for reading Zynx address ROM
7) fixed bug that caused broadcasts to not work shortly after booting (only
manifested if not using multicast - e.g. not in FreeBSD 2.0)
8) fixed spelling errors in comments
Submitted by: Matt Thomas
then goes into all the directories a `make kprog' would have and
does it there, too. This should complete the krbdist, except that P-HK
has to figure out where in his build process he wants to build and install
this stuff.
for ioconf.c with the current and suppress the generation if they are
equal. This now prevents all the warnings from the c-compiler about
sio or snd or two adaptecs. This works only if the sio lines are grouped
together in the config files, but it is better than nothing.
a decimal value.
I don't have the time to deal with users typing in partition names
such as "FreeBSD" at the moment so just allow the numerical id to be
specified for the moment.
Could do with some cosmetic tuning regarding placement and things.
Fixed some dialog code (from Andrew).
Pass mountpoints onto stage2 in a struct fstab *mounts[]
Fix all the field connections to conform to the new L&F document.
Removed a layer of menus.
Auto select partition to install into -- first FreeBSD partition
in MBR table. Abort if no FreeBSD partition.
Added a F_BUTTON type.
Fixed up label editor to show free space properly.
Fixed a few bugs.
Subject: Mea culpa -- small fix for netboot fixes
In accordance with the unavoidable principle sof Murphy's Law, I discovered
that the fixes I recently contributed for the netboot code had some small
flaws in them. Two of them were just typos and had no effect on how the
program functioned. The other one was a missing line from the rootopts and
swapopts functions I created in bootmenu.c, which was supposed to initialize
the NFS sotype flag. It defaults to UDP, and you can change it to TCP with
the rootopts or swapopts commands, but then you can't change it back again.
I originally had a line at the top of each function to reinitialize this
flag, but somehow it got lost in the shuffle, probably because I don't
actually have a need for that flag yet.
Submitted by: wpaul
menu items aren't unique enough. After half an hour of head-scratching,
here are the disgusting convolutions required to work around the problem.
Sigh..
Sigh. It's hard to test something that screws up a running system when
it works, so I have to do most of this through the rather laborious process
of making boot floppies! ;-(
Change the reference for the libtermcap libtermlib link from SHLIBDIR
to LIBDIR. SHLIBDIR is undefined in the standard case.
termcap.c:
Initialize a local variable to zero. Otherwise an erroneous free call
can happen and clobber the calling program.
Seen with vi and gdb. If you have TERMCAP set with a terminal entry and
set TERM with something like huhu, vi and gdb core dumps.
That was the good news. The bad news is that bad144 is a proper mess,
and I don't have time to fix it now, so you will probably not be able to
use it anyway.
Sorry guys, go out and buy a 100Mb IDE drive and a paddleboard :-(
If somebody wants to pick up on this: bad144 needs to learn how to
stay inside our slice of the disk. That's the trick.
Go to a single dependancy in files.i386. Using a .c file for the
sequencer code won't work since I need to know the size of the program,
so we just include the generated .h file as:
"../../sys/gnu/misc/aic7770/aic7770_seq.h"
Reviewed by:
Submitted by:
Obtained from:
instead. The entire scheme just doesn't work as envisioned (hint: think
about make depend as well as all). Those extremely rare individuals who
actually hack on the sequencer code will know how to keep stuff in sync,
I *do* get the feeling!
Somehow, I don't think this stuff was tested at all! :-(
I really hope that it actually works, though my hopes are steadily diminishing.
Anyone with 27xx/28xx boards in -current is *strongly encouraged* to give this
stuff a shot! Otherwise, I suspect that we'll be punting this out of
2.0. I haven't found a single part of Justin's commit that wasn't broken
in some way.
in getting mirror-2.3 to work with FreeBSD, i found that timelocal.pl has
a bug. a patch is included below. this needs to be applied to both
src/gnu/usr.bin/perl/lib/timelocal.pl and
src/usr.sbin/xntpd/scripts/monitoring/timelocal.pl
Reviewed by:
Submitted by:
Obtained from:
in getting mirror-2.3 to work with FreeBSD, i found that timelocal.pl has
a bug. a patch is included below. this needs to be applied to both
src/gnu/usr.bin/perl/lib/timelocal.pl and
src/usr.sbin/xntpd/scripts/monitoring/timelocal.pl
Submitted by: jmb
/*
* filename [ standard | optional ] [ config-dependent ]
* [ dev* | profiling-routine ] [ device-driver] [ no-obj ]
* [ compile-with "compile rule" [no-implicit-rule] ]
* [ dependancy "dependancy-list"]
*/
I added
no-obj - This entry does not create anything linkable to the kernel.
dependancy - Add additional dependancy rules to a target.
no-implicit-rule - Don't assume .c -> .o type rules. Config is really
dumb in this area and assumes that everything is a .c file
irregarless of extention. This was the best choice really
since there may even be .c file that you don't want to follow
the standard rules.
This was all done so that the building to the aic7770 assembler and using
the aic7770 assembler in the building of the aic7770 driver could be config
dependant. I can now have an entry like this for the driver:
aic7770 optional ahc device-driver \
compile-with "${CC} $> -o $@" \
dependancy "$S/gnu/misc/aic7770/aic7770.c" \
no-obj no-implicit-rule
aic7770_seq.h optional ahc device-driver \
compile-with "${.CURDIR}/aic7770 -o $@ $S/gnu/misc/aic7770/aic7770.seq"\
dependancy "$S/gnu/misc/aic7770/aic7770.seq aic7770" \
no-obj no-implicit-rule
i386/isa/aic7770.c optional ahc device-driver \
dependancy "aic7770_seq.h"
I also added '\' escaping to newlines so that this doesn't look as gross as
it could have.
Reviewed by: jkh
of config so YOU MUST RECOMPILE CONFIG. Modifying config was the cleanest
solution to integrating this driver into the tree which will become more
obvious in the next commit.
a discussion going on about removing this code from the burden of the
GPL, but it won't happen before Beta, and this code should be tested
before release.
Supports 27/2842 class adaptec cards and is almost capable of supporting
aic7870 based adapters (294X series cards). It does not support Wide
controllers or the second channel on Twin boards although I have work in
progress on getting both channels and running.
I have also added a few performance improvements to this version that give
us approximately a 25% boost over the original driver. These patches have
been submitted to the author.
Obtained from: Linux aic7770 driver (John Aycock - [email protected])
that Poul builds the rest of the dists properly. I'll run this over the
XFree86 dist, but the rest will be up to him. Check bindist rule for
the single line to add - it's trivial.
2. See if swapon() failed and at least print a diagnostic.
3. Use -1 instead of strheight()/strwidth() everywhere.
Reviewed by:
Submitted by:
Obtained from:
Smack the netboot program around so that it will allow the user to
specify mount options. [So that you can boot from a privileged port]
Change the default boot image name in netboot to /kernel, then strip
the leading slash when actually going out to get the NFS file handle.
Added support for 3Com 3c503 cards. Also added another command to
the (trans) that allows you to switch the 3Com's on-board transceiver
on and off. (ether.c, ether.h, bootmenu.c)
Modified the Makefile to support new compile-time options for 3c503
cards:
-DINCLUDE_3COM Include support for 3c503
-D_3COM_BASE=0x300 Define 3c503 base i/o address (if not
specified, 0x300 is the default)
-D_3COM_USE_AUI Disable the 3c503's transceiver by
default (without this flag the transceiver
is on by default)
and it doesn't support --unlink. I think it's time to nuke cpio completely
out of the installation process, unless someone can think of a really good
reason to keep it (and don't say multiple volume extraction since we a) don't
use it anywhere anyway, and b) tar supports that too, now).
for Wine support. The current snapshot of wine works fine with this.
This should go into the beta as the code which it calls in the kernel is
already there, and works fine.
Further investigation showed that prefix was erroneously set to /usr/local
for X11 based ports as well, when the assumption was that they'd really go
into ${X11BASE} (an /etc/make.conf variable that the user's free to set).
Set X11BASE to /usr/X11R6 if the user hasn't already, and assume that
the user really wants prefix to point there when the port is XMKMF based.
that the english in Ugen's two replacement pages is not too impenetrable! :-)
[Note: Poul - please pull these into the BETA branch along with the
other firewall changes]
Submitted by: ugen
struct lfs.
[email protected]:
The pad2 field in struct lfs is a kludge. You
need it because the raw devices has to be written in DEV_BSIZE. The
lfs_maxsymlinklen is needed because the tells the UFS code that we
want to use 4.4BSD directory layout insted of FreeBSD 1.1.5.
Reviewed by: Justin Gibbs
Submitted by: [email protected]
buffering scheme and make it more in tune with FreeBSD's vfs_bio
implementation. The filesystem seems fairly stable, but I wouldn't recommend
it to anyone not willing to experience problems. This is very green code and
has the limitation that YOU CAN ONLY HAVE ONE LFS PARTITION MOUNTED AT A TIME.
What LFS is good for:
Non fsynced writes FASTER THAN FFS
Large deletions Increadibly fast
Reads are a little bit slower than FFS right now, but that is a factor of
how under optimized this code is. LFS should in theory perform at least as
well as FFS under fsync (iozone) type loads, and this is what I'm currently
working on.
Reviewed by: Justin Gibbs
Submitted by: John Dyson
Obtained from:
stages of debugging LFS:
* if we can't bmap, use old VOP code
*/
! if (/* (vp->v_mount && vp->v_mount->mnt_stat.f_type == MOUNT_LFS) || */
! VOP_BMAP(vp, foff, &dp, 0, 0)) {
for (i = 0; i < count; i++) {
if (i != reqpage) {
vnode_pager_freepage(m[i]);
--- 804,810 ----
/*
* if we can't bmap, use old VOP code
*/
! if (VOP_BMAP(vp, foff, &dp, 0, 0)) {
Reviewed by: gibbs
Submitted by: John Dyson
MASTER_SITE_OVERRIDE - If set in the environment, will override everyone's
MASTER_SITES settings. Useful if you'd prefer to point to a
distfiles repository somewhere closer.
MASTER_SITE_FREEBSD - Sets OVERRIDE to be FreeBSD's own master repository.
already C++ safe, or C++ header files.
This fixes the problem with parse errors in header files when compiling C++
files.
Recompiling libg++ also solves the undefined synbols problem.
be callable _after_ installation in 2.1's system admin tools. This is
almost totally revamped now.
2. Support installation from DOS partition or floppy.
3. Many stray bogons eliminated. Perhaps a few introduced. One more
rev should fix this up, once I've spammed my test machine a couple of
times.
4. Installation from CD now *really* possible.
5. Allow user to specify arbitary subdirectories for NFS mountpoints -
UFS, NFS and CD distributions now share many common elements.
was supposed to have already been made, but got botched somewhere.
Don't clobber the last page of memory (where the message buffer is). Some
BIOS don't gratuitously wipe it out on reboot.
Remove bogus declaration of Debugger(). Call Debugger() even if DDB is
not defined, but still call panic() after Debugger() returns, although
most other SCSI drivers just call Debugger().
printf() is inconsistent with the prototype for the library printf() and
gets declared if DIAGNOSTIC is defined because <vm/vm_page.h> includes
<sys/systm.h>.
Notice that the libgcc DOESN'T change number, because there are no
changes.
Also now the gnu2bmake stuff is synchronized again.
I commit this so that others can test too.
You might want to postpone any "make worlds" until tomorrow, to
avoid any problems I didn't see in the first pass.
Thanks to Bruce for rounding up our changes to gcc.
Change the sc_link structure from 8 targets with 8 lun's to
16 targets with 8 lun's. Wide scsi and the ncr 825 does support 16 targets.
scsiconf.c:
move the addition of the trailing NUL's out of a then clause, they are also
needed in the else clause for an unknown device.
Alphabetize.
Write all i/o functions in sleep so that we don't use anything from
NetBSD.
Restore the correct type of u_int for ports. This saves a whole cycle
per i/o on 486's.
Change `inline' back to __inline to avoid compiler warnings with
-Wreally-all.
Don't implement bdb() unless BDE_DEBUGGER is defined. Declare bdb_exists
outside the function to avoid hundreds of compiler warnings.
Let the compiler pick the register in asms if possible.
Implement ffs() using inline asm(). gcc provides a slightly different
one. It was broken in gcc-2.4.5 but works now. Declaring a correct
version inline ensures getting a correct version. FreeBSD-1.1.5 has
an slow inline version but FreeBSD-2.0 has a library version (which
probably never gets used).
Do inb() and outb() without using %edx for constant ports below 0x100.
Remove casts to the same type in queue functions.
Declare prototypes for everything implemented i386/*.s and also for
everything that is normally implemented as an inline here (I don't
like the current complete dependency on gcc). Ifdef out the prototypes
that are declared elsewhere. THere should be a separate header to
declare things implemented in i386/*.s, but then it would be harder
to override declarations with inlines.
${UII}
with the current default exception (un)mask. There should be no such
processes unless you change the mask. Someday the mask should be
changed to the IEEE default of everything masked. The npx state
gets saved so that it can be checked and this may have the side effect
of fixing a bug that was reported for 1.1.5. (npx exceptions may
sometimes leak across exits and clobber another process. I can't see
how this can happen.)
Get some missing/wrong declarations from headers now that the headers
have them.
I couldn't find a better way to avoid compiler warnings about
redundant and/or inconsistent declaration of ffs(). I'd like to
be able to declare prototypes in general headers without committing
to implementing them as `static inline' or `extern', but there
seems to be no way to do this with gcc-2.6.1. E.g.,
int foo(void);
static __inline int foo(void) { return 1; }
causes a warning about the linkage mismatch, while the opposite
order causes a warning about the redundant declaration.
the following.
Move declarations to and from <machine/segments.h>. Make segment stuff
static if possible.
Remove unused (although initialized) global variables _default_ldt,
currentldt, _gsel_tss (rename the latter to the auto variable
gtel_tss).
Use "correct" and consistent types for interrupt handlers.
Remove a mailing address from the code.
Fix type mismatches found by adding prototypes.
Partly support BDE_DEBUGGER. Still broken by conflict with APM. Does
nothing if BDE_DEBUGGER is not defined.
Clean up prototypes and data declarations. Declare most of the segment
functions that are implemented in support.s. Make data private in
machdep.c if possible.
Parenthesize expressions in macros properly!
${Uniformize idempotency ifdef}.
to avoid compiler warnings.
Clean up prototypes: alphabetize; don't use redundant `extern' or
meaningless `extern inline'.
Uniformize idempotency ifdef.
(These functions are implemented in assembler so the compiler can't
check the declarations.)
Clean up prototypes: restore CSRG's alphabetical order, arg names in
prototypes, formatting to fit in 80 columns
Declare a complete prototype for the function pointer *ifa_rtrequest.
radix.h:
Declare a complete prototype for the function pointer *rnh_walktree
and for the function rn_walktree.
Uniformize idempotency ifdef.
Disable the bogus declaration of pmap_bootstrap(). Since its arg list
is machine-dependent, it must be declared in a machine-dependent header.
vm_page.h:
Change `inline' to `__inline' and old-style function parameter lists for
inlined functions to new-style.
`inline' and old-style function parameter lists should never be used in
system headers, even in very machine-dependent ones, because they cause
warnings from gcc -Wreally-all.
$(DESTDIR)/$(LIBDIR) (I need SHLIBDIR. The / was a bug and the
$(...) style was inconsistent.)
Install ordinary libraries in ${DESTDIR}${LIBDIR} instead of in
$(DESTDIR)/$(LIBDIR).
Change remaining $(...) to ${...}.
Define SHLIBDIR?= ${LIBDIR} and install shared libraries in
${DESTDIR}${SHLIBDIR} instead of in ${DESTDIR}${LIBDIR}.
SHLIBDIR may be defined in /etc/make.conf to override the
default of /usr/lib (I use /lib). Other changes are required
for non-default shared library directories to actually work
(ld* and crtso have too many hard-coded paths).
Bruce
more like binaries. This is hard to do using a general rules because
the natural `.sh:' rule has a null suffix and null suffixes are broken.
(With 1.1.5's make they sometimes work and sometimes cause core dumps.
2.0's make has a botched fixed and they never work.)
RANTOUCH may be defined in /etc/make.conf as
`${ECHO} skipping ${RANLIB} -t' to help stop `make install' from
changing the timestamps on unchanged libraries, thus making the
uninstalled binaries appear to be out of date... Other changes
are required to stop install from clobbering the timestamps.
Comment about missing libraries for LIBDES, LIBKDB, LIBKRB, LIBMP, LIBPC
and LIBPLOT.
Don't define LIBDBM since it was replaced by db in libc.
Remove duplication. ${DESTDIR}/usr/lib/... gives /usr/lib/... even when
DESTDIR is not defined.
get truncated to LONG_MAX. Don't lobotomize the merged library source.
Make all private data static.
Use int_parms for the i/o "address" since the "address" is really a number
and is represented as an int.
Add command `flags' to allow changing device flags.
Fix scrolling of device listing. Only scrolling of the current devtab
was controlled. Reprint the header after scrolling.
Rename commands and change strings to match their config(8) keywords:
io -> port
IOaddr -> port
mem -> iomem (abbreviation is io :-()
MemAddr -> iomem
case changes
Don't use NULL for ASCII NUL.
Call strtoul() with base 0 for both numbers and addresses so that input
is consistent and hex and octal can be used for numbers.
Fix entry of irq number. Check the range at no extra cost. It wasn't
possible to enter irq -1.
Format device listing better. Large numbers (such as 0xffffffff for the
GENERIC lpt0 port) messed up the formatting.
Show the unit number in the device listing. Comment about the fields
that aren't shown.
fault was at offset 0 in the object. This resulted in more overhead but
was othewise benign. Added incore() check in vnode_pager_has_page()
to work around a problem with LFS...other than slightly higher overhead,
this change has no affect on UFS.
put the stuff into the right "distribution". As default things end up
in "bindist".
Normal (ie: most) makefiles know naught of this.
More commits will follow, which will direct various parts of the tree
into the distribution we want them in.
Some of the grief of being release-engineer is supposed to go away with this.
later be applied to a number of programs (inetd for instance) to clean
out the bogus code doing the same thing, modulus all the bugs.
If you need to read a '#'-is-a-comment-file, please use these routines.
I realize that the shlib# should be bumped (for the non-US world:
increased by something), but will defer this until something significant
happens.
of the 1.1.5 driver, a recent version of the NetBSD driver, Andres'
transmission start threshold code, and all other relavent changes to the driver
since it was brought into 2.0. The multicast support from NetBSD has not be
folded in yet. I've tested it under high loads for two weeks and it is now
robust enough to be included in the GENERIC kernel.
Reviewed by: gibbs
Submitted by: [email protected] (Andres Vega Garcia)
often on USENET.
Added comments regarding the new 'extended IDE' controllers, which work with
FreeBSD but do not use the extended features.
Minor formatting changes.
input fields. It reads a template file passed to init_forms(char *)
and creates a curses based form editor. See the examples directory
for a basic demo.
1.2MB barrier again. I tell ya, Poul, it's a losing game! You shave
50 bytes off, the next change takes 100 back, and this is just ALPHA!
The 1.2MB weenies will _just have to buy new drives_!
scsi adapter. Let it work on every adapter. Someone want to rewrite
this to be coupled with the adapter specification in the config file,
so that you can say which adapters need it ?
cosmetique) because we already have right things there or his changes
are incorrect.
Fix mcd_subchan to return position, inspired by idea from
[email protected], but different implementation.
Add an interrupt handler for trigger-happy users.
Add domain to resolv.conf
More general cleanup in preparation for this script being split into
several scripts.
You can get ps easily to core dump, if you are running a "make depend"
on a kernel in one window and a "ps -auxww" in another. The ww will
try to give you the full argument list of the command that can
now be 64Kb large, but ps expected only 4Kb large arg arrays and
doesn't check for overflows.
This attempts to make the installion a little less grating by not
clearing the screen every time a like-sized dialog is going to splat
on top of another one. If you don't want the screen to clear, set
clear="", otherwise leave it set to (or set it back to) "--clear".
It can't be set to "" all the time since then small dialogs appearing
on top of big dialogs look funky.
I'm going to re-roll the boot floppies to have this in, and hopefully
Poul will update it into his world tree before making the bin tarballs.
Be a real shame to leave this incorrect! Very sorry, Soren! It was
simply an updating oversight! :-(
Loaded 100 of 10438 files, more files were not shown because too many files have changed in this diff.
Show more
Reference in new issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
Peter Wemm