Let firmware do its best first, and if it can't, try software recovery.
I would remove software timeout handler completely, but found bunch of
complains on command timeout on sparc64 mailing list few years ago, so
better be safe in case of interrupt loss.
For 24xx and above use 2 vectors (default and response queue).
For 26xx and above use 3 vectors (default, response and ATIO queues).
Due to global lock interrupt hardlers never run simultaneously now, but
at least this allows to save one regitster read per interrupt.
There were two copies of the code: one in generic code was half-broken, and
another in platform code was never called. Leave only one in generic code
and working.
Instead of single isp_intr() function doing all possible magic, introduce
four different functions to handle mailbox operation completions, async
events, response and ATIO queues. The goal is to isolate different code
paths to make code more readable, and to make easier support for multiple
interrupt vectors. Even oldest hardware in many cases can identify what
code path it should run on interrupt. Contemporary hardware can assign
them to different interrupt vectors.
It was implemented to reduce context switches when uploading firmware to
card's RAM. But this mechanism is not used last 10 years since all mbox
operations are now polled, and it was never used for cards produced in
last 15 years. Newer cards can use DMA to upload firmware.
This change fixes DMA resource leak on driver unload. Also it removes
DMA resources allocation for hardcoded number of requests before fetching
the real number from firmware. Also it prepares ground for more flexible
IRQs allocation according to firmware capabilities.
Always null-terminate ccb_pathinq.(sim_vid|hba_vid|dev_name)
The sim_vid, hba_vid, and dev_name fields of struct ccb_pathinq are
fixed-length strings. AFAICT the only place they're read is in
sbin/camcontrol/camcontrol.c, which assumes they'll be null-terminated.
However, the kernel doesn't null-terminate them. A bunch of copy-pasted code
uses strncpy to write them, and doesn't guarantee null-termination. For at
least 4 drivers (mpr, mps, ciss, and hyperv), the hba_vid field actually
overflows. You can see the result by doing "camcontrol negotiate da0 -v".
This change null-terminates those fields everywhere they're set in the
kernel. It also shortens a few strings to ensure they'll fit within the
16-character field.
PR: 215474
Reported by: Coverity
CID: 1009997 1010000 1010001 1010002 1010003 1010004 1010005
CID: 1331519 1010006 1215097 1010007 1288967 1010008 1306000
CID: 1211924 1010009 1010010 1010011 1010012 1010013 1010014
CID: 1147190 1010017 1010016 1010018 1216435 1010020 1010021
CID: 1010022 1009666 1018185 1010023 1010025 1010026 1010027
CID: 1010028 1010029 1010030 1010031 1010033 1018186 1018187
CID: 1010035 1010036 1010042 1010041 1010040 1010039
This allows to properly handle cases when target wants to receive or send
more data then initiator wants to send or receive. Previously in such
cases isp(4) returned CAM_DATA_RUN_ERR, while now it returns resid > 0.
- Move private data about ATIOs/INOTs from per-LUN to per-channel data.
This allows active commands to continue operation after LUN destruction.
This also simplifies lookup of the data by tag in some situations.
- Unify three restart_queue processing implementations.
- Complete all ATIOs from restart_queue on LUN disable.
- Delete ATIO private data when command completed or aborted, not depending
on the ATIO being requeued, that was ugly hack and could never happen. CAM
should always call ether XPT_CONT_TARGET_IO with status or XPT_ABORT.
- Implement XPT_ABORT for queued ATIOs/INOTs to allow CAM do graceful
shutdown, not depending on LUN disable, as it is done in ahd(4)/targ(4).
- Unify isp_endcmd() arguments to make it more usable in generic code.
- Remove never really used LUN state reference counter.
For some reason isp_handle_platform_notify_fc() allocated INOT just
before calling isp_handle_platform_target_tmf(), which also allocates
INOT. It seems to be a braino introduced in r196008.
All resources lack of which may put CTIO into the queue are either
per-channel or potentially per-queue, but none of them are per-LUN.
This is a first step to fix live LUN disabling. Before this change
any CTIOs held in a queue in time of disabling were just leaked.
------------------------------------------------------------------------
r313568 | ken | 2017-02-10 15:02:45 -0700 (Fri, 10 Feb 2017) | 68 lines
Change the isp(4) driver to not adjust the tag type for REQUEST SENSE.
The isp(4) driver was changing the tag type for REQUEST SENSE
commands to Head of Queue, when the CAM CCB flag
CAM_TAG_ACTION_VALID was NOT set. CAM_TAG_ACTION_VALID is set
when the tag action in the XPT_SCSI_IO is not CAM_TAG_ACTION_NONE
and when the target has tagged queueing turned on.
In most cases when CAM_TAG_ACTION_VALID is not set, it is because
the target is not doing tagged queueing. In those cases, trying to
send a Head of Queue tag may cause problems. Instead, default to
sending a simple tag.
IBM tape drives claim to support tagged queueing in their standard
Inquiry data, but have the DQue bit set in the control mode page
(mode page 10). CAM correctly detects that these drives do not
support tagged queueing, and clears the CAM_TAG_ACTION_VALID flag
on CCBs sent down to the drives.
This caused the isp(4) driver to go down the path of setting the
tag action to a default value, and for Request Sense commands only,
set the tag action to Head of Queue.
If an IBM tape drive does get a Head of Queue tag, it rejects it with
Invalid Message Error (0x49,0x00). (The Qlogic firmware translates that
to a Transport Error, which the driver translates to an Unrecoverable
HBA Error, or CAM_UNREC_HBA_ERROR.) So, by default, it wasn't possible
to get a good response from a REQUEST SENSE to an FC-attached IBM
tape drive with the isp(4) driver.
IBM tape drives (tested on an LTO-5 with G9N1 firmware and a TS1150
with 4470 firmware) also have a bug in that sending a command with a
non-simple tag attribute breaks the tape drive's Command Reference
Number (CRN) accounting and causes it to ignore all subsequent
commands because it and the initiator disagree about the next
expected CRN. The drives do reject the initial command with a head
of queue tag with an Invalid Message Error (0x49,0x00), but after that
they ignore any subsequent commands. IBM confirmed that it is a bug,
and sent me test firmware that fixes the bug. However tape drives in
the field will still exhibit the bug until they are upgraded.
Request Sense is not often sent to targets because most errors are
reported automatically through autosense in Fibre Channel and other
modern transports. ("Modern" meaning post SCSI-2.) So this is not
an error that would crop up frequently. But Request Sense is useful on
tape devices to report status information, aside from error reporting.
This problem is less serious without FC-Tape features turned on,
specifically precise delivery of commands (which enables Command
Reference Numbers), enabled on the target and initiator. Without
FC-Tape features turned on, the target would return an error and
things would continue on.
And it also does not cause problems for targets that do tagged
queueing, because in those cases the isp(4) driver just uses the
tag type that is specified in the CCB, assuming the
CAM_TAG_ACTION_VALID flag is set, and defaults to sending a Simple
tag action if it isn't an ordered or head of queue tag.
sys/dev/isp/isp.c:
In isp_start(), don't try to send Request Sense commands
with the Head of Queue tag attribute if the CCB doesn't
have a valid tag action. The tag action likely isn't valid
because the target doesn't support tagged queueing.
Sponsored by: Spectra Logic
------------------------------------------------------------------------
------------------------------------------------------------------------
r310338 | ken | 2016-12-20 14:17:07 -0700 (Tue, 20 Dec 2016) | 37 lines
Turn on FC-Tape by default in the isp(4) driver.
FC-Tape provides additional link level error recovery, and is
highly recommended for tape devices. It will only be turned on for
a given target if the target supports it.
Without this setting, we default to whatever FC-Tape setting is in
NVRAM on the card.
This can be overridden by setting the following loader tunable, for
example for isp0:
hint.isp.0.nofctape=1
sys/conf/options:
Add a new kernel config option, ISP_FCTAPE_OFF, that
defaults the FC-Tape configuration to off.
sys/dev/isp/isp_pci.c:
If ISP_FCTAPE_OFF is defined, turn off FC-Tape. Otherwise,
turn it on if the card supports it.
share/man/man4/isp.4:
Add a description of FC-Tape to the isp(4) man page.
Add descriptions of the fctape and nofctape options, as well as the
ISP_FCTAPE_OFF kernel configuration option.
Add the ispfw module and kernel drivers to the suggested
configurations at the top of the man page so that users are less
likely to leave it out. The driver works well with the included
firmware, but may not work at all with whatever firmware the user
has flashed on their card.
Sponsored by: Spectra Logic
------------------------------------------------------------------------
Sponsored by: Spectra Logic
utilizing previously unused arg field of struct ccb_notify_acknowledge.
This makes new QUERY TASK, QUERY TASK SET and QUERY ASYNC EVENT requests
really functional for CAM target mode drivers.
This code was originally implemented 7 years ago, but never really worked
due to trivial error. I think this functionality may be not required.
Initiators supporting optional periodic command status checks detected
those terminated commands and retried them 3 seconds later. But thinking
about less featured initiators and the fact that it is our race makes
virtual ports "unknown" it may be good to have this feature.
Alexander Motin