Allow building if_ffec as a module.
if_ffec bugfixes related to harvesting of hardware-maintained statistics...
After harvesting the hardware statistics counters and summing them into the
interface stats, properly clear the hardware counters back to zero. On imx5
and earlier hardware it is necessary to disable collection of stats while
writing zeroes to all the registers. On imx6 and newer it turns out it's
not even possible to write zeroes, instead you have to toggle a special
"zero everything" control bit in a register.
Count incoming packets with a bad start frame delim as input errors, and
incoming packets dropped due to no fifo space as input drops.
Remove all code related to harvesting the hardware stats less often than
once per second. It turns out the 32-bit stats registers are backed by
16-bit counters under the hood, and they can easily roll over if you only
harvest them once every 3 seconds like the old code was doing. Now we just
read all the regs once a second.
The combination of not properly zeroing the stats registers and 16-bit
counters sometimes wrapping between harvest calls resulted in basically
unusable statistics before these changes.
Add new mlx5ib(4) driver to the kernel source tree which supports
Remote DMA over Converged Ethernet, RoCE, for the ConnectX-4 series of
PCI express network cards.
There is currently no user-space support and this driver only supports
kernel side non-routable RoCE V1. The krping kernel module can be used
to test this driver. Full user-space support including RoCE V2 will be
added as part of the ongoing upgrade to ibcore from Linux 4.9. Otherwise
this driver is feature equivalent to mlx4ib(4). The mlx5ib(4) kernel
module will only be built when WITH_OFED=YES is specified.
Sponsored by: Mellanox Technologies
r320628, r319201, r320629, r320630, r320631, r320632.
r317518:
Import Amazon Elastic Network Adapter (ENA) HAL to sys/contrib/
Import from vendor-sys/ena-com/1.1.4.1
SVN rev.: 317516
Version: 1.1.4.1
r318647:
Add support for Amazon Elastic Network Adapter (ENA) NIC
ENA is a networking interface designed to make good use of modern CPU
features and system architectures.
The ENA device exposes a lightweight management interface with a
minimal set of memory mapped registers and extendable command set
through an Admin Queue.
The driver supports a range of ENA devices, is link-speed independent
(i.e., the same driver is used for 10GbE, 25GbE, 40GbE, etc.), and has
a negotiated and extendable feature set.
Some ENA devices support SR-IOV. This driver is used for both the
SR-IOV Physical Function (PF) and Virtual Function (VF) devices.
ENA devices enable high speed and low overhead network traffic
processing by providing multiple Tx/Rx queue pairs (the maximum number
is advertised by the device via the Admin Queue), a dedicated MSI-X
interrupt vector per Tx/Rx queue pair, and CPU cacheline optimized
data placement.
The ENA driver supports industry standard TCP/IP offload features such
as checksum offload and TCP transmit segmentation offload (TSO).
Receive-side scaling (RSS) is supported for multi-core scaling.
The ENA driver and its corresponding devices implement health
monitoring mechanisms such as watchdog, enabling the device and driver
to recover in a manner transparent to the application, as well as
debug logs.
Some of the ENA devices support a working mode called Low-latency
Queue (LLQ), which saves several more microseconds. This feature will
be implemented for driver in future releases.
r319197:
Add mbuf defragmentation to the ENA driver
When mbuf chain is too long and device cannot handle that number
of segments in DMA transaction, mbuf chain will be defragmented.
Initially, driver was dropping all mbuf chains that were exceeding
supported number of segments.
r319198:
Add locks before each ena_up and ena_down
Lock only ena_up and ena_down calls in ioctl handler, instead of whole
ioctl. Locking ioctl with sx lock that is sleepable, is not allowed in
some cases, e.g. when multicast options are being changed.
Additional locking was added in deatch function to prevent race condition
with ioctl function.
r319199:
Add error handling to the ENA driver if init of the reset task fails
Also, to simplify cleaning routine, reset task is initialized before
allocating statistics and other resources.
r319200:
Move ENA's hw stats updating routine to separate task
Initially, stats were being updated each time OS was requesting for
the first statistic.
To read statistics from hw, condvar was used. cv_timedwait cannot be
called when unsleepable lock is held, and this happens when FreeBSD
is requesting statistic.
Seperate task is reading statistics from NIC each 1 second.
r319201:
Introduce additional locks when releasing TX resources and buffers in ENA
There could be race condition with TX cleaning routine when cleaning mbufs,
when it was called directly from main sending thread (ena_mq_start).
r320625:
Add missing lock upon initialization of the interface
Lack of this lock was causing crash if down was called in
parallel with the initialization routine.
r320626:
Acquire locks before calling drbr_flush()
It is required to hold lock that is associated with buffer ring before
flushing drbr.
r320628:
Unmask all IO irqs after driver state is set as running
If driver left MSI-x handlling routine because interface was put down,
it is not unmasking IRQs, so any requesting interrupt will be awaiting
for unmasking.
On ena_up() routine all interrupts are being unmasked and any awaiting
interrupt will be handled right away.
If handler was executed before driver state was set as running, handling
routine is being ended immediately, leaving IO irqs for given queue
masked.
r320629:
Call drbr_advance() before leaving TX routine
If drbr_advance() is not called before doing cleanup and packet is
already enqueued for sending (tx_info is holding pointer to mbuf), then
mbuf is cleaned both in drbr_flush() and in cleanup routine, when all
mbufs hold by tx_buffer_info are being released.
This causes panic, because mbuf is released twice.
r320630:
Remove RX mtx from ENA driver
RX lock is no longer required. There can only be one RX cleanup task
running at a time, RX cleanup cannot be executed if interface is not
yet initialized and ena_down() will not free any RX resources if any io
interrupt is being handled - RX cleanup task is only called from an
interrupt handler.
r320631:
Fix creation of dma tags and TSO settings
TSO settings were not reflecting real HW capabilities.
DMA tags were created with wrong window - high address was the same as
low, so excluding window was not working.
Capabilities of TX dma transaction were not set properly - TSO max size
had been increased and size of one segment had been adjusted.
r320632:
Replace mbuf defragmentation with collapse
Collapse should be more effective than defragmentation.
Added missing declaration of ena_check_and_collapse_mbuf().
Submitted by: Michal Krawczyk <[email protected]>
Jakub Palider <[email protected]>
Jan Medala <[email protected]>
Obtained from: Semihalf, Amazon.com Inc.
Sponsored by: Amazon.com Inc.
r314651:
sys/modules: normalize .CURDIR-relative paths to SRCTOP
This simplifies make output/logic
Tested with: `cd sys/modules; make ALL_MODULES=` on amd64
r318439:
Normalize .PATH on SRCTOP
This will help Jenkins dedupe 9 warnings between the static build and
the module build of ipsec(4).
Missed in SRCTOP conversion in r314651.
MFC with: r314651
r318440:
Normalize SYSDIR on SRCTOP instead of .CURDIR
This is being done to simplify pathing for CFLAGS and source files.
r318007:
Add intermediary Makefile for compiling all items in the directory
r318008:
Only compile tests/ if MK_TESTS != no or ALL_MODULES is defined
r318009:
Add MK_TESTS to kern.opts.mk to support r31800
MFC with: r318008
Pointyhat to: ngie
r318011:
Mark this Makefile SUBDIR_PARALLEL
I inserted the necessary SUBDIR+= .WAIT in the previous commit
r314659:
usr.sbin: normalize paths using SRCTOP-relative paths or :H when possible
This simplifies make logic/output
r314676:
Fix build after r314656
Some of the changes I introduced to use .ALLSRC were correct in spirit,
but incorrect in reality -- in particular, ../Makefile.inc hadn't been
pulled in via bsd.init.mk (via bsd.lib.mk, bsd.prog.mk), so the value
of .ALLSRC (evaluated immediately) was empty. .include bsd.init.mk
explicitly so we can be certain that the values used as dependencies in
the targets are defined when the target recipe has been evaluated.
Reminder: thou shalt separate out separate functional changes before
committing them.
(YUGE) Pointyhat to: ngie
In collaboration with: bdrewery
Add ipfw_pmod kernel module.
The module is designed for modification of a packets of any protocols.
For now it implements only TCP MSS modification. It adds the external
action handler for "tcp-setmss" action.
A rule with tcp-setmss action does additional check for protocol and
TCP flags. If SYN flag is present, it parses TCP options and modifies
MSS option if its value is greater than configured value in the rule.
Then it adjustes TCP checksum if needed. After handling the search
continues with the next rule.
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D10150
Move logging via BPF support into separate file.
* make interface cloner VNET-aware;
* simplify cloner code and use if_clone_simple();
* migrate LOGIF_LOCK() to rmlock;
* add ipfw_bpf_mtap2() function to pass mbuf to BPF;
* introduce new additional ipfwlog0 pseudo interface. It differs from
ipfw0 by DLT type used in bpfattach. This interface is intended to
used by ipfw modules to dump packets with additional info attached.
Currently pflog format is used. ipfw_bpf_mtap2() function uses second
argument to determine which interface use for dumping. If dlen is equal
to ETHER_HDR_LEN it uses old ipfw0 interface, if dlen is equal to
PFLOG_HDRLEN - ipfwlog0 will be used.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
MFC r304043:
Add three helper function to manage tables from external modules.
ipfw_objhash_lookup_table_kidx does lookup kernel index of table;
ipfw_ref_table/ipfw_unref_table takes and releases reference to table.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
MFC r304046, 304108:
Add ipfw_nat64 module that implements stateless and stateful NAT64.
The module works together with ipfw(4) and implemented as its external
action module.
Stateless NAT64 registers external action with name nat64stl. This
keyword should be used to create NAT64 instance and to address this
instance in rules. Stateless NAT64 uses two lookup tables with mapped
IPv4->IPv6 and IPv6->IPv4 addresses to perform translation.
A configuration of instance should looks like this:
1. Create lookup tables:
# ipfw table T46 create type addr valtype ipv6
# ipfw table T64 create type addr valtype ipv4
2. Fill T46 and T64 tables.
3. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
4. Create NAT64 instance:
# ipfw nat64stl NAT create table4 T46 table6 T64
5. Add rules that matches the traffic:
# ipfw add nat64stl NAT ip from any to table(T46)
# ipfw add nat64stl NAT ip from table(T64) to 64:ff9b::/96
6. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Stateful NAT64 registers external action with name nat64lsn. The only
one option required to create nat64lsn instance - prefix4. It defines
the pool of IPv4 addresses used for translation.
A configuration of instance should looks like this:
1. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
2. Create NAT64 instance:
# ipfw nat64lsn NAT create prefix4 A.B.C.D/28
3. Add rules that matches the traffic:
# ipfw add nat64lsn NAT ip from any to A.B.C.D/28
# ipfw add nat64lsn NAT ip6 from any to 64:ff9b::/96
4. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6434
MFC r304048:
Replace __noinline with special debug macro NAT64NOINLINE.
MFC r304061:
Use %ju to print unsigned 64-bit value.
MFC r304076:
Make statistics nat64lsn, nat64stl an nptv6 output netstat-like:
"@value @description" and fix build due to -Wformat errors.
MFC r304378 (by bz):
Try to fix gcc compilation errors (which are right).
nat64_getlasthdr() returns an int, which can be -1 in case of error,
storing the result in an uint8_t and then comparing to < 0 is not
helpful. Do what is done in the rest of the code and make proto an
int here as well.
MFC r309187:
Fix ICMPv6 Time Exceeded error message translation.
MFC r314718:
Use new ipfw_lookup_table() in the nat64 too.
MFC r315204,315233:
Use memset with structure size.
Add ipfw_nptv6 module that implements Network Prefix Translation for IPv6
as defined in RFC 6296. The module works together with ipfw(4) and
implemented as its external action module. When it is loaded, it registers
as eaction and can be used in rules. The usage pattern is similar to
ipfw_nat(4). All matched by rule traffic goes to the NPT module.
Reviewed by: hrs
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6420
MFC r304049:
Add `stats reset` command implementation to NPTv6 module
to be able reset statistics counters.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
MFC r304076:
Make statistics nat64lsn, nat64stl an nptv6 output netstat-like:
"@value @description" and fix build due to -Wformat errors.
MFC r314507:
Fix NPTv6 rule counters when one_pass is not enabled.
Consider the rule matching when both @done and @retval values
returned from ipfw_run_eaction() are zero. And modify ipfw_nptv6()
to return IP_FW_DENY and @done=0 when addresses do not match.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
Remove the kernel optoion for IPSEC_FILTERTUNNEL, which was deprecated
more than 7 years ago in favour of a sysctl in r192648.
MFC r305122:
Remove redundant sanity checks from ipsec[46]_common_input_cb().
This check already has been done in the each protocol callback.
MFC r309144,309174,309201 (by fabient):
IPsec RFC6479 support for replay window sizes up to 2^32 - 32 packets.
Since the previous algorithm, based on bit shifting, does not scale
with large replay windows, the algorithm used here is based on
RFC 6479: IPsec Anti-Replay Algorithm without Bit Shifting.
The replay window will be fast to be updated, but will cost as many bits
in RAM as its size.
The previous implementation did not provide a lock on the replay window,
which may lead to replay issues.
Obtained from: [email protected]
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D8468
MFC r309143,309146 (by fabient):
In a dual processor system (2*6 cores) during IPSec throughput tests,
we see a lot of contention on the arc4 lock, used to generate the IV
of the ESP output packets.
The idea of this patch is to split this mutex in order to reduce the
contention on this lock.
Update r309143 to prevent false sharing.
Reviewed by: delphij, markm, ache
Approved by: so
Obtained from: [email protected]
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D8130
MFC r313330:
Merge projects/ipsec into head/.
Small summary
-------------
o Almost all IPsec releated code was moved into sys/netipsec.
o New kernel modules added: ipsec.ko and tcpmd5.ko. New kernel
option IPSEC_SUPPORT added. It enables support for loading
and unloading of ipsec.ko and tcpmd5.ko kernel modules.
o IPSEC_NAT_T option was removed. Now NAT-T support is enabled by
default. The UDP_ENCAP_ESPINUDP_NON_IKE encapsulation type
support was removed. Added TCP/UDP checksum handling for
inbound packets that were decapsulated by transport mode SAs.
setkey(8) modified to show run-time NAT-T configuration of SA.
o New network pseudo interface if_ipsec(4) added. For now it is
build as part of ipsec.ko module (or with IPSEC kernel).
It implements IPsec virtual tunnels to create route-based VPNs.
o The network stack now invokes IPsec functions using special
methods. The only one header file <netipsec/ipsec_support.h>
should be included to declare all the needed things to work
with IPsec.
o All IPsec protocols handlers (ESP/AH/IPCOMP protosw) were removed.
Now these protocols are handled directly via IPsec methods.
o TCP_SIGNATURE support was reworked to be more close to RFC.
o PF_KEY SADB was reworked:
- now all security associations stored in the single SPI namespace,
and all SAs MUST have unique SPI.
- several hash tables added to speed up lookups in SADB.
- SADB now uses rmlock to protect access, and concurrent threads
can do SA lookups in the same time.
- many PF_KEY message handlers were reworked to reflect changes
in SADB.
- SADB_UPDATE message was extended to support new PF_KEY headers:
SADB_X_EXT_NEW_ADDRESS_SRC and SADB_X_EXT_NEW_ADDRESS_DST. They
can be used by IKE daemon to change SA addresses.
o ipsecrequest and secpolicy structures were cardinally changed to
avoid locking protection for ipsecrequest. Now we support
only limited number (4) of bundled SAs, but they are supported
for both INET and INET6.
o INPCB security policy cache was introduced. Each PCB now caches
used security policies to avoid SP lookup for each packet.
o For inbound security policies added the mode, when the kernel does
check for full history of applied IPsec transforms.
o References counting rules for security policies and security
associations were changed. The proper SA locking added into xform
code.
o xform code was also changed. Now it is possible to unregister xforms.
tdb_xxx structures were changed and renamed to reflect changes in
SADB/SPDB, and changed rules for locking and refcounting.
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D9352
MFC r313331:
Add removed headers into the ObsoleteFiles.inc.
MFC r313561 (by glebius):
Move tcp_fields_to_net() static inline into tcp_var.h, just below its
friend tcp_fields_to_host(). There is third party code that also uses
this inline.
MFC r313697:
Remove IPsec related PCB code from SCTP.
The inpcb structure has inp_sp pointer that is initialized by
ipsec_init_pcbpolicy() function. This pointer keeps strorage for IPsec
security policies associated with a specific socket.
An application can use IP_IPSEC_POLICY and IPV6_IPSEC_POLICY socket
options to configure these security policies. Then ip[6]_output()
uses inpcb pointer to specify that an outgoing packet is associated
with some socket. And IPSEC_OUTPUT() method can use a security policy
stored in the inp_sp. For inbound packet the protocol-specific input
routine uses IPSEC_CHECK_POLICY() method to check that a packet conforms
to inbound security policy configured in the inpcb.
SCTP protocol doesn't specify inpcb for ip[6]_output() when it sends
packets. Thus IPSEC_OUTPUT() method does not consider such packets as
associated with some socket and can not apply security policies
from inpcb, even if they are configured. Since IPSEC_CHECK_POLICY()
method is called from protocol-specific input routine, it can specify
inpcb pointer and associated with socket inbound policy will be
checked. But there are two problems:
1. Such check is asymmetric, becasue we can not apply security policy
from inpcb for outgoing packet.
2. IPSEC_CHECK_POLICY() expects that caller holds INPCB lock and
access to inp_sp is protected. But for SCTP this is not correct,
becasue SCTP uses own locks to protect inpcb.
To fix these problems remove IPsec related PCB code from SCTP.
This imply that IP_IPSEC_POLICY and IPV6_IPSEC_POLICY socket options
will be not applicable to SCTP sockets. To be able correctly check
inbound security policies for SCTP, mark its protocol header with
the PR_LASTHDR flag.
Differential Revision: https://reviews.freebsd.org/D9538
MFC r313746:
Add missing check to fix the build with IPSEC_SUPPORT and without MAC.
MFC r313805:
Fix LINT build for powerpc.
Build kernel modules support only when both IPSEC and TCP_SIGNATURE
are not defined.
MFC r313922:
For translated packets do not adjust UDP checksum if it is zero.
In case when decrypted and decapsulated packet is an UDP datagram,
check that its checksum is not zero before doing incremental checksum
adjustment.
MFC r314339:
Document that the size of AH ICV for HMAC-SHA2-NNN should be half of
NNN bits as described in RFC4868.
PR: 215978
MFC r314812:
Introduce the concept of IPsec security policies scope.
Currently are defined three scopes: global, ifnet, and pcb.
Generic security policies that IKE daemon can add via PF_KEY interface
or an administrator creates with setkey(8) utility have GLOBAL scope.
Such policies can be applied by the kernel to outgoing packets and checked
agains inbound packets after IPsec processing.
Security policies created by if_ipsec(4) interfaces have IFNET scope.
Such policies are applied to packets that are passed through if_ipsec(4)
interface.
And security policies created by application using setsockopt()
IP_IPSEC_POLICY option have PCB scope. Such policies are applied to
packets related to specific socket. Currently there is no way to list
PCB policies via setkey(8) utility.
Modify setkey(8) and libipsec(3) to be able distinguish the scope of
security policies in the `setkey -DP` listing. Add two optional flags:
'-t' to list only policies related to virtual *tunneling* interfaces,
i.e. policies with IFNET scope, and '-g' to list only policies with GLOBAL
scope. By default policies from all scopes are listed.
To implement this PF_KEY's sadb_x_policy structure was modified.
sadb_x_policy_reserved field is used to pass the policy scope from the
kernel to userland. SADB_SPDDUMP message extended to support filtering
by scope: sadb_msg_satype field is used to specify bit mask of requested
scopes.
For IFNET policies the sadb_x_policy_priority field of struct sadb_x_policy
is used to pass if_ipsec's interface if_index to the userland. For GLOBAL
policies sadb_x_policy_priority is used only to manage order of security
policies in the SPDB. For IFNET policies it is not used, so it can be used
to keep if_index.
After this change the output of `setkey -DP` now looks like:
# setkey -DPt
0.0.0.0/0[any] 0.0.0.0/0[any] any
in ipsec
esp/tunnel/87.250.242.144-87.250.242.145/unique:145
spid=7 seq=3 pid=58025 scope=ifnet ifname=ipsec0
refcnt=1
# setkey -DPg
::/0 ::/0 icmp6 135,0
out none
spid=5 seq=1 pid=872 scope=global
refcnt=1
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D9805
PR: 212018
Relnotes: yes
Sponsored by: Yandex LLC
[intelspi] Add SPI driver for Intel BayTrail SoC
Add SPI mode (PIO-only) support for Intel Synchronous Serial Port that
can be found in several Intel's products starting from PXA family.
Most of implementations have slight differences in behavior and in
addresses for registers subset. This driver covers only BayTrail SoC
implementation for it's the only hardware I have to test it on.
Driver attaches to ACPI bus only and does not have PCI or FDT support
for now due to lack of hardware to test it on.
"intelspi" is the best name I've managed to come up with. Linux driver
name (spi-pxa2xx) does not make sense because current implementation
does not support actual PXA2xx SoCs. And as far as I know there is no
codename assigned to Intel SSP chip.
Reviewed by: br, manu
Differential Revision: https://reviews.freebsd.org/D8896
For whatever reason, smapi, smbios, vpd are all under the "bios" directory.
smapi is only for i386, so the entire "bios" directory is only built for
i386. Break smapi out, and make only it i386-specific. Then, build the
"bios" directory for both amd64 and i386.
r308696:
New driver for Broadcom NetXtreme-C and NetXtreme-E devices.
r308729:
Add bnxt(4) to the hardware notes.
r308787:
Add missing newline in error mesage
r308813:
Check link status after init
r309028:
Add missing break to switch statement
r309073:
Fix version string
r309078:
Add new device IDs
Approved by: sbruno
Relnotes: yes
Sponsored by: Broadcom Limited
r308898:
[bytgpio] Fix USB disconnect event after listsing pins on gpioc2
- Do not set input flag when reading value from GPIO pin, it is not
required and for gpioc2(S5 bank) setting both input and output flags
leads to some kind of electric interference (curren drop?) that
causes USB devices to disconnect
- Check pad configuration when attaching device and provide IN/OUT
capabilities only for pads that are configured as GPIO. Do not let
user code to configure or change value of non-GPIO pads. There is
no information for NC bank in intel's datasheet so for now function
check is ignored for pins in it
Reported by: Frank H.
MFC after: 3 days
r308940:
[bytgpio] prepare bytgpio(4) for modularization
- Add detach method
- module should depend on gpiobus, not gpio
r308942:
[bytgpio] Add module for bytgpio(4)
MFC after: 3 days
r308944 by hiren@:
r308942 broke kernel build.
Add acpi_if.h to module makefile to fix it.
Submitted by: peter
r309112:
[bytgpio] Fix pc98 build by disabling bytgpio module for this platform
Reported by: dim
r306530:
Declare a module for evdev and add dependency to ukbd(4) and ums(4)
Prepare for making evdev a module. "Pure" evdev device drivers (like
touchscreen) and evdev itself can be built as a modules regardless of
"options EVDEV" in kernel config. So if people does not require evdev
functionality in hybrid drivers like ums and ukbd they can, for instance,
kldload evdev and utouchscreen to run FreeBSD in kiosk mode.
r306531:
Add dependency to evdev module (if required)
r306532:
Add dependency to evdev module
r306579:
Modularize evdev
- Convert "options EVDEV" to "device evdev" and "device uinput", add
modules for both new devices. They are isolated subsystems and do not
require any compile-time changes to general kernel subsytems
- For hybrid drivers that have evdev as an optional way to deliver input
events add option EVDEV_SUPPORT. Update all existing hybrid drivers
to use it instead of EVDEV
- Remove no-op DECLARE_MODULE in evdev, it's not required, MODULE_VERSION
is enough
- Add evdev module dependency to uinput
Submitted by: Vladimir Kondratiev <[email protected]>
r304555, r304556, r304557, r304558, r304559, r304561, r304563, r304564,
r304565, r304615, r304742, r304743, r304744, r304745, r304748, r304886,
r304991, r305928, r305938, r305987, r306185:
Bring CloudABI support back in sync with HEAD.
- Add support for running 32-bit executables on amd64, armv6 and i386.
- As these new architectures require the use of the vDSO, merge back
vDSO support for 64-bit executables running on amd64 and arm64 as
well. This has the advantage that support for vDSO-less execution
can be phased out when 11.0 becomes unsupported, as opposed to 11.x.
This change has been tested by running the cloudlibc unit tests on all
supported architectures, which seems to work fine.
Add kernel interfaces to call EFI Runtime Services.
MFC r306104:
Fix build of the module outside the kernel tree.
MFC r306209 (by imp):
Change the efi_get_table interface to a void **.
MFC r306351:
Handle TLB shootdown IPI during the EFI runtime calls, on SandyBridges.
default. At least initially, the feature to support multiple TCP stacks is
aimed at supporting advanced use cases and TCP development, but it is not
necessarily aimed at a wide audience. Therefore, there is no need to build
and install the extra TCP stacks by default. Instead, the people who are
using or developing this functionality can add the extra option to build/
install the extra TCP stacks.
However, we do want to build the extra TCP stacks as part of test builds
(e.g. LINT or tinderbox) to ensure that developers who are testing their
changes will know that their changes do not break the additional TCP
stack modules.
After this change, a user will need to add WITH_EXTRA_TCP_STACKS=1 to
make.conf or the kernel config in order to build the extra TCP modules.
Differential Revision: https://reviews.freebsd.org/D6795
Reviewed by: sjg
Approved by: re (kib)
This is an initial work in progress to use the replacement bhnd
bus code for devices which support it.
* Add manpage updates for bhnd, bhndb, siba
* Add kernel options for bhnd, bhndbus, etc
* Add initial support in if_bwn_pci / if_bwn_mac for using bhnd
as the bus transport for suppoted NICs
* if_bwn_pci will eventually be the PCI bus glue to interface to bwn,
which will use the right backend bus to attach to, versus direct
nexus/bhnd attachments (as found in embedded broadcom devices.)
The PCI glue defaults to probing at a lower level than the bwn glue,
so bwn should still attach as per normal without a boot time tunable set.
It's also not fully fleshed out - the bwn probe/attach code needs to be
broken out into platform and bus specific things (just like ath, ath_pci,
ath_ahb) before we can shift the driver over to using this.
Tested:
* BCM4311, STA mode
* BCM4312, STA mode
Submitted by: Landon Fuller <[email protected]>
Differential Revision: https://reviews.freebsd.org/D6191
Make it compile only for i386/amd64 for now as it's been tested there.
It's quite possible it'll show up elsewhere and we can enable it
for other architectures later.
Tested:
* PC Engines APU1C4
Submitted by: Daniel Wyatt <[email protected]>
Reviewed by: adrian, loos
Differential Revision: https://reviews.freebsd.org/D5389
There's some upcoming work to add new chipset support here and I'd
like to only add 802.11n support to one driver, instead of both
urtwn and rtwn.
There's also missing support for things like 802.11n, some powersave
work, bluetooth integration/coexistence, etc, and also newer parts
(like 8192EU, maybe some 11ac parts, not sure yet.)
So, this is hopefully the first step in a longer set of steps to unify
rtwn/urtwn and extend it with more interesting chipset and functionality
support.
Reviewed by: kevlo
improve cancellation robustness.
Introduce a new file operation, fo_aio_queue, which is responsible for
queueing and completing an asynchronous I/O request for a given file.
The AIO subystem now exports library of routines to manipulate AIO
requests as well as the ability to run a handler function in the
"default" pool of AIO daemons to service a request.
A default implementation for file types which do not include an
fo_aio_queue method queues requests to the "default" pool invoking the
fo_read or fo_write methods as before.
The AIO subsystem permits file types to install a private "cancel"
routine when a request is queued to permit safe dequeueing and cleanup
of cancelled requests.
Sockets now use their own pool of AIO daemons and service per-socket
requests in FIFO order. Socket requests will not block indefinitely
permitting timely cancellation of all requests.
Due to the now-tight coupling of the AIO subsystem with file types,
the AIO subsystem is now a standard part of all kernels. The VFS_AIO
kernel option and aio.ko module are gone.
Many file types may block indefinitely in their fo_read or fo_write
callbacks resulting in a hung AIO daemon. This can result in hung
user processes (when processes attempt to cancel all outstanding
requests during exit) or a hung system. To protect against this, AIO
requests are only permitted for known "safe" files by default. AIO
requests for all file types can be enabled by setting the new
vfs.aio.enable_usafe sysctl to a non-zero value. The AIO tests have
been updated to skip operations on unsafe file types if the sysctl is
zero.
Currently, AIO requests on sockets and raw disks are considered safe
and are enabled by default. aio_mlock() is also enabled by default.
Reviewed by: cem, jilles
Discussed with: kib (earlier version)
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D5289
rtwnfw got added in r293009 and depends on source-less and
non-free microcode in sys/contrib/dev/rtwn.
PR: 205874
Submitted by: Fabian Keil
Obtained from: ElectroBSD
The mdio driver interface is generally useful for devices that require
MDIO without the full MII bus interface. This lifts the driver/interface
out of etherswitch(4), and adds a mdio(4) man page.
Submitted by: Landon Fuller <[email protected]>
Differential Revision: https://reviews.freebsd.org/D4606
to do is to clean up the timer handling using the async-drain.
Other optimizations may be coming to go with this. Whats here
will allow differnet tcp implementations (one included).
Reviewed by: jtl, hiren, transports
Sponsored by: Netflix Inc.
Differential Revision: D4055
Use hhook(9) framework to achieve ability of loading and unloading
if_enc(4) kernel module. INET and INET6 code on initialization registers
two helper hooks points in the kernel. if_enc(4) module uses these helper
hook points and registers its hooks. IPSEC code uses these hhook points
to call helper hooks implemented in if_enc(4).
default and add a manual page for mlx5en. The mlx5 module contains
shared code for both infiniband and ethernet. The mlx5en module
contains specific code for ethernet functionality only. A mlx5ib
module is in the works for infiniband support.
Supported hardware:
- ConnectX-4: 10/20/25/40/50/56/100Gb/s speeds.
- ConnectX-4 LX: 10/25/40/50Gb/s speeds (low power consumption)
Refer to the mlx5en(4) manual page for a comprehensive list.
The team porting the mlx5 driver(s) to FreeBSD:
- Hans Petter Selasky <[email protected]>
- Oded Shanoon <[email protected]>
- Meny Yossefi <[email protected]>
- Shany Michaely <[email protected]>
- Shahar Klein <[email protected]>
- Daria Genzel <[email protected]>
- Mark Bloch <[email protected]>
Differential Revision: https://reviews.freebsd.org/D4163
Submitted by: Mark Block <[email protected]>
Sponsored by: Mellanox Technologies
Reviewed by: gnn @
MFC after: 3 days
Ed Maste