The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an
original error code. Stop calling request_threaded_irq() with the invalid
IRQ #s.
Fixes: 9ba96ae507 ("usb: omap1: Tahvo USB transceiver driver")
Acked-by: Felipe Balbi <[email protected]>
Signed-off-by: Sergey Shtylyov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
The driver neglects to check the result of platform_get_irq()'s calls and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing them both to fail with -EINVAL, overriding
an original error code. Stop calling request_threaded_irq() with the
invalid IRQ #s.
Fixes: c33fad0c37 ("usb: otg: Adding twl6030-usb transceiver driver for OMAP4430")
Acked-by: Felipe Balbi <[email protected]>
Signed-off-by: Sergey Shtylyov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling request_irq() with the invalid IRQ #s.
Fixes: 0807c500a1 ("USB: add Freescale USB OTG Transceiver driver")
Acked-by: Felipe Balbi <[email protected]>
Signed-off-by: Sergey Shtylyov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
The B_SESS_VLD_WAKEUP_EN bit 6 was added by a mistake in a previous
commit. This bit corresponds to B_SESS_END_WAKEUP_EN, which we don't use.
The B_VBUS_VLD_WAKEUP_EN doesn't exist at all and B_SESS_VLD_WAKEUP_EN
needs to be in place of it. We don't utilize B-sensors in the driver,
so it never was a problem, nevertheless let's correct the definition of
the bits.
Fixes: 35192007d2 ("usb: phy: tegra: Support waking up from a low power mode")
Signed-off-by: Dmitry Osipenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Some devices need an extra delay after losing VBUS, otherwise VBUS may
be detected as active at suspend time, preventing the PHY's suspension
by the VBUS detection sensor. This problem was found on Asus Transformer
TF700T (Tegra30) tablet device, where the USB PHY wakes up immediately
from suspend because VBUS sensor continues to detect VBUS as active after
disconnection. We need to poll the PHY's VBUS wakeup status until it's
deasserted before suspending PHY in order to fix this minor trouble.
Fixes: 35192007d2 ("usb: phy: tegra: Support waking up from a low power mode")
Reported-by: Maxim Schwalm <[email protected]> # Asus TF700T
Tested-by: Maxim Schwalm <[email protected]> # Asus TF700T
Reviewed-by: Peter Chen <[email protected]>
Signed-off-by: Dmitry Osipenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
The USB charger type and status was already propagated to userspace
through kobject_uevent_env during charger notify work. Nevertheless the
uevent could be lost e.g. because it could be fired at an early kernel
boot stage, way before udev daemon or any other user-space app was able
to catch it. Registering uevent hook for introduced usb_phy_dev_type
will allow to query sysfs 'uevent' file to restore that information at
any time.
Reviewed-by: Peter Chen <[email protected]>
Signed-off-by: Grzegorz Jaszczyk <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
The commit 2a6c0b82e6 ("USB: PHY: JZ4770: Add support for new
Ingenic SoCs.") introduced the initialization function for different
chips, but left the relevant code involved in the resetting process
in the original function, resulting in uninitialized variable calls.
Fixes: 2a6c0b82e6 ("USB: PHY: JZ4770: Add support for new Ingenic SoCs.").
Signed-off-by: 周琰杰 (Zhou Yanjie) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Reformat the code (add one level of indentation before the values),
to align the code in the macro definition section.
Tested-by: 周正 (Zhou Zheng) <[email protected]>
Co-developed-by: 漆鹏振 (Qi Pengzhen) <[email protected]>
Signed-off-by: 漆鹏振 (Qi Pengzhen) <[email protected]>
Signed-off-by: 周琰杰 (Zhou Yanjie) <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
Add support for probing the phy-jz4770 driver on the JZ4780 SoC,
the X1000 SoC and the X1830 SoC from Ingenic.
Tested-by: 周正 (Zhou Zheng) <[email protected]>
Co-developed-by: 漆鹏振 (Qi Pengzhen) <[email protected]>
Signed-off-by: 漆鹏振 (Qi Pengzhen) <[email protected]>
Signed-off-by: 周琰杰 (Zhou Yanjie) <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
1.Modify the macro definition to unify "#define USBPCR_XXXX n"
into the "#define USBPCR_XXXX (n << USBPCR_XXXX_LSB)" style,
so as to unify the code style in the "jz4770_phy_init()" and
simplify the code.
2.Remove unused macro definitions to simplify the code.
Tested-by: 周正 (Zhou Zheng) <[email protected]>
Suggested-by: Paul Cercueil <[email protected]>
Signed-off-by: 周琰杰 (Zhou Yanjie) <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
No idea why this driver is using a char device node, statically
allocated, with no dynamic allocation or hook up with devtmpfs, along
with a reserverd major number, for "special" operations, not all of
which ever were implemented.
So just rip it out, as no one must be using it because no modern system
will ever actually create the /dev/ node it needs.
Cc: Felipe Balbi <[email protected]>
Reviewed-by: Ran Wang <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
This file has a HUGE debugging sysfs file that spews out a lot of
information all at once, which violates the one-value-per-file rule for
sysfs. If this is really needed, it should go into debugfs, but given
the age of this driver, I strongly doubt anyone is using it anymore.
So just remove the file entirely, it was never documented, so obviously,
no one actually needed it :)
Cc: Felipe Balbi <[email protected]>
Reviewed-by: Ran Wang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Kerneldoc expects arg descriptions to be in the format '@.*: '. If either
the '@' or the ':' is omitted then kerneldoc complains that the description
is missing. Add the missing ':'s here.
Also provide a new description for 'event'.
Fixes the following kernel build W=1 warnings:
drivers/usb/phy/phy.c:106: warning: Function parameter or member 'work' not described in 'usb_phy_notify_charger_work'
drivers/usb/phy/phy.c:172: warning: Function parameter or member 'nb' not described in 'usb_phy_get_charger_type'
drivers/usb/phy/phy.c:172: warning: Function parameter or member 'state' not described in 'usb_phy_get_charger_type'
drivers/usb/phy/phy.c:172: warning: Function parameter or member 'data' not described in 'usb_phy_get_charger_type'
drivers/usb/phy/phy.c:194: warning: Function parameter or member 'usb_phy' not described in 'usb_phy_set_charger_current'
drivers/usb/phy/phy.c:194: warning: Function parameter or member 'mA' not described in 'usb_phy_set_charger_current'
drivers/usb/phy/phy.c:244: warning: Function parameter or member 'usb_phy' not described in 'usb_phy_get_charger_current'
drivers/usb/phy/phy.c:244: warning: Function parameter or member 'min' not described in 'usb_phy_get_charger_current'
drivers/usb/phy/phy.c:244: warning: Function parameter or member 'max' not described in 'usb_phy_get_charger_current'
drivers/usb/phy/phy.c:281: warning: Function parameter or member 'usb_phy' not described in 'usb_phy_set_charger_state'
drivers/usb/phy/phy.c:281: warning: Function parameter or member 'state' not described in 'usb_phy_set_charger_state'
drivers/usb/phy/phy.c:427: warning: Function parameter or member 'dev' not described in 'devm_usb_get_phy'
drivers/usb/phy/phy.c:427: warning: Function parameter or member 'type' not described in 'devm_usb_get_phy'
drivers/usb/phy/phy.c:456: warning: Function parameter or member 'type' not described in 'usb_get_phy'
drivers/usb/phy/phy.c:500: warning: Function parameter or member 'dev' not described in 'devm_usb_get_phy_by_node'
drivers/usb/phy/phy.c:500: warning: Function parameter or member 'node' not described in 'devm_usb_get_phy_by_node'
drivers/usb/phy/phy.c:500: warning: Function parameter or member 'nb' not described in 'devm_usb_get_phy_by_node'
drivers/usb/phy/phy.c:558: warning: Function parameter or member 'dev' not described in 'devm_usb_get_phy_by_phandle'
drivers/usb/phy/phy.c:558: warning: Function parameter or member 'phandle' not described in 'devm_usb_get_phy_by_phandle'
drivers/usb/phy/phy.c:558: warning: Function parameter or member 'index' not described in 'devm_usb_get_phy_by_phandle'
drivers/usb/phy/phy.c:590: warning: Function parameter or member 'dev' not described in 'devm_usb_put_phy'
drivers/usb/phy/phy.c:590: warning: Function parameter or member 'phy' not described in 'devm_usb_put_phy'
drivers/usb/phy/phy.c:627: warning: Function parameter or member 'type' not described in 'usb_add_phy'
drivers/usb/phy/phy.c:721: warning: Function parameter or member 'event' not described in 'usb_phy_set_event'
Cc: Felipe Balbi <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
In the function tegra_usb_phy_probe(), if usb_add_phy_dev() failed,
the return value will be given to err, and if usb_add_phy_dev() succeed,
the return value will be zero. Thus it is unnecessary to repeated check
here.
Signed-off-by: Zhang Shengju <[email protected]>
Signed-off-by: Tang Bin <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
A call to 'regulator_get()' is hidden in 'twl6030_usb_ldo_init()'. A
corresponding put must be performed in the error handling path, as
already done in the remove function.
While at it, also move a 'free_irq()' call in the error handling path in
order to be consistent.
Reviewed-by: Dan Carpenter <[email protected]>
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
This patch corrects the SPDX License Identifier style in
header files related to Physical Layer USB driver configuration.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <[email protected]>
Signed-off-by: Nishad Kamdar <[email protected]>
Link: https://lore.kernel.org/r/20200419123559.GA4505@nishad
Signed-off-by: Greg Kroah-Hartman <[email protected]>
The driver uses only GPIO Descriptor Consumer Interface so include
proper header. This fixes compile test failures (e.g. on i386):
drivers/usb/phy/phy-tegra-usb.c: In function ‘ulpi_phy_power_on’:
drivers/usb/phy/phy-tegra-usb.c:695:2: error:
implicit declaration of function ‘gpiod_set_value_cansleep’ [-Werror=implicit-function-declaration]
drivers/usb/phy/phy-tegra-usb.c: In function ‘tegra_usb_phy_probe’:
drivers/usb/phy/phy-tegra-usb.c:1167:11: error:
implicit declaration of function ‘devm_gpiod_get_from_of_node’ [-Werror=implicit-function-declaration]
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Dmitry Osipenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Tools like Coccinelle may erroneously recommend to use the
devm_platform_ioremap_resource() API for the registers mapping because
these tools are not aware about the implementation details of the driver.
Let's add a clarifying comments to the code, which should help to stop
future attempts to break the driver.
Signed-off-by: Dmitry Osipenko <[email protected]>
Acked-by: Thierry Reding <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Instead of using the legacy GPIO API and keeping track on
polarity inversion semantics in the driver, switch to use
GPIO descriptors for this driver and change all consumers
in the process.
This makes it possible to retire platform data completely:
the only remaining platform data member was "wakeup" which
was intended to make the vbus interrupt wakeup capable,
but was not set by any users and thus remained unused. VBUS
was not waking any devices up. Leave a comment about it so
later developers using the platform can consider setting it
to always enabled so plugging in USB wakes up the platform.
Cc: Daniel Mack <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Acked-by: Robert Jarzmik <[email protected]>
Acked-by: Felipe Balbi <[email protected]>
Acked-by: Sylwester Nawrocki <[email protected]>
Acked-by: Philipp Zabel <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
The last user of the phy generic platform data was
deleted in commit 1e041b6f31
("usb: dwc3: exynos: Remove dead code"). So get rid of
the platform data, which rids us of another consumer of
the legacy GPIO API at the same time. Make sure we
only inlcude <linux/gpio/consumer.h> which is all we use.
Alter the usb_phy_gen_create_phy() function prototype to
not pass any platform data as this is just hardcoded to
NULL at all locations calling it in the kernel.
Move the devm_gpiod_get* calls out of the if (of_node)
parenthesis, as these calls are generic and do not depend
on device tree, they are used by any hardware description.
Cc: Marek Szyprowski <[email protected]>
Cc: Felipe Balbi <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
It's unlikely that two drivers could manage PHY's state simultaneously in
practice, nevertheless the utmip_pad_count checking should be under lock,
for consistency.
Signed-off-by: Dmitry Osipenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
It is much more intuitive if reset is treated as asserted when GPIO value
is set to 1. All NVIDIA Tegra device-trees are properly specifying active
state of the reset-GPIO since 2013, let's clean up that part of the code.
Signed-off-by: Dmitry Osipenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Zhiwei Yang