Pull chrome platform updates from Benson Leung:
"cros_ec_typec:
- Clean up use of cros_ec_check_features
cros_ec_*:
- Rename and move cros_ec_pd_command to cros_ec_command, and make
changes to cros_ec_typec and cros_ec_proto to use the new common
command, reducing duplication.
sensorhub:
- simplify getting .driver_data in cros_ec_sensors_core and
cros_ec_sensorhub
misc:
- Maintainership change. Enric Balletbo i Serra has moved on from
Collabora, so removing him from chrome/platform maintainers. Thanks
for all of your hard work maintaining this, Enric, and best of luck
to you in your new role!
- Add Prashant Malani as driver maintainer for cros_ec_typec.c and
cros_usbpd_notify. He was already principal contributor of these
drivers"
* tag 'tag-chrome-platform-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_proto: Use ec_command for check_features
platform/chrome: cros_ec_proto: Use EC struct for features
MAINTAINERS: Chrome: Drop Enric Balletbo i Serra
platform/chrome: cros_ec_typec: Use cros_ec_command()
platform/chrome: cros_ec_proto: Add version for ec_command
platform/chrome: cros_ec_proto: Make data pointers void
platform/chrome: cros_usbpd_notify: Move ec_command()
platform/chrome: cros_usbpd_notify: Rename cros_ec_pd_command()
platform/chrome: cros_ec: Fix spelling mistake "responsed" -> "response"
platform/chrome: cros_ec_sensorhub: simplify getting .driver_data
iio: common: cros_ec_sensors: simplify getting .driver_data
platform/chrome: cros-ec-typec: Cleanup use of check_features
platform/chrome: cros_ec_proto: Fix check_features ret val
MAINTAINERS: Add Prashant's maintainership of cros_ec drivers
Pull watchdog updates from Wim Van Sebroeck:
- f71808e_wdt: convert to watchdog framework
- db8500_wdt: Rename driver (was ux500_wdt.c)
- sunxi: Add compatibles for R329 and D1
- mtk: add disable_wdt_extrst support
- several other small fixes and improvements
* tag 'linux-watchdog-5.16-rc1' of git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: db8500_wdt: Rename symbols
watchdog: db8500_wdt: Rename driver
watchdog: ux500_wdt: Drop platform data
watchdog: bcm63xx_wdt: fix fallthrough warning
watchdog: iTCO_wdt: No need to stop the timer in probe
watchdog: s3c2410: describe driver in KConfig
watchdog: sp5100_tco: Add support for get_timeleft
watchdog: mtk: add disable_wdt_extrst support
dt-bindings: watchdog: mtk-wdt: add disable_wdt_extrst support
watchdog: rza_wdt: Use semicolons instead of commas
watchdog: mlx-wdt: Use regmap_write_bits()
watchdog: rti-wdt: Make use of the helper function devm_platform_ioremap_resource()
watchdog: iTCO_wdt: Make use of the helper function devm_platform_ioremap_resource()
watchdog: ar7_wdt: Make use of the helper function devm_platform_ioremap_resource_byname()
watchdog: sunxi_wdt: Add support for D1
dt-bindings: watchdog: sunxi: Add compatibles for D1
ar7: fix kernel builds for compiler test
dt-bindings: watchdog: sunxi: Add compatibles for R329
watchdog: meson_gxbb_wdt: add timeout parameter
watchdog: meson_gxbb_wdt: add nowayout parameter
...
MFD_SIMPLE_MFD_I2C should select the MFD_CORE to a prevent build error:
aarch64-linux-ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_probe':
drivers/mfd/simple-mfd-i2c.c:55: undefined reference to `devm_mfd_add_devices'
Cc: <[email protected]>
Fixes: c753ea3178 ("mfd: simple-mfd-i2c: Add support for registering devices via MFD cells")
Signed-off-by: Robert Marko <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Considering the current transition of the GPIO subsystem, remove all
dependencies of the legacy GPIO interface (linux/gpio.h and linux
/of_gpio.h) and replace it with the descriptor-based GPIO approach.
Signed-off-by: Maíra Canal <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/YXDEBCiSnXYRQPXt@fedora
show() must not use snprintf() when formatting the value to be
returned to user space.
Fix the following coccicheck warning:
drivers/mfd/janz-cmodio.c:157: WARNING: use scnprintf or sprintf.
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Signed-off-by: Qing Wang <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Without the header, the MODULE_DEVICE_TABLE() declaration fails:
drivers/mfd/altera-a10sr.c:153:1: error: data definition has no type or storage class [-Werror]
153 | MODULE_DEVICE_TABLE(of, altr_a10sr_spi_of_match);
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Up to now tps65912_device_exit() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Up to now stmpe_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Up to now mc13xxx_common_exit() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
The resource_size defines that:
res->end - res->start + 1;
The origin original code is:
sysmgr_config.max_register = res->end - res->start - 3;
So, the correct fix is that:
sysmgr_config.max_register = resource_size(res) - 4;
Fixes: d12edf9661 ("mfd: altera-sysmgr: Use resource_size function on resource object")
Signed-off-by: Kai Song <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
The Arizona driver has both some devices which only have an I2C
interface and some which only have a SPI interface. Currently both of
these share an of_match table, but this means inapproriate compatibles
are available for each interface. Tidy this up by creating a table for
each interface listing only the appropriate compatibles.
Reported-by: Mark Brown <[email protected]>
Signed-off-by: Charles Keepax <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding a SPI device ID table.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <[email protected]>
Reviewed-by: Baolin Wang <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding a SPI device ID table.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding a SPI device ID table.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Early exits from for_each_child_of_node() should decrement the
node reference counter. Reported by Coccinelle:
drivers/mfd/mfd-core.c:197:2-24: WARNING:
Function "for_each_child_of_node" should have of_node_put() before goto around lines 209.
Fixes: c94bb233a9 ("mfd: Make MFD core code Device Tree and IRQ domain aware")
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 14577/77836 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and charger driver, so using
level sensitive interrupt is here especially important to avoid races.
With an edge configuration in case if first PMIC signals interrupt
followed shortly after by the RTC, the interrupt might not be yet
cleared/acked thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77693 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77686 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Samsung PMIC drivers are used only on Devicetree boards.
Additionally, the PMIC datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
Marek Szyprowski reports that together with DTS change (proper level in
DTS) it fixes RTC alarm failure that he observed from time to time on
TM2e board.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Tested-by: Marek Szyprowski <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
The MODULE_DEVICE_TABLE already creates proper alias. Having another
MODULE_ALIAS causes the alias to be duplicated:
$ modinfo cros_ec_dev.ko
alias: platform:cros-ec-dev
srcversion: F84A69D2156719A4F717A76
alias: platform:cros-ec-dev
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
The description mentioned AD5520, which is a different device.
Fixed the typo.
Signed-off-by: Ramona Alexandra Nechita <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
This update adds new regmap to support the latest EA silicon
which will be selected based on the chip and variant
information read from the device.
Signed-off-by: Carlos de Paula <[email protected]>
Reviewed-by: Adam Thomson <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
RK817 has a power-off bit in SYS_CFG3. Add support for powering
off the PMIC.
Signed-off-by: Ondrej Jirman <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
The intel_pmt driver shows up as a compile option for all arches but is
32-bit and 64-bit x86 specific.
Add a CONFIG dependency on X86 for intel_pmt.
Signed-off-by: Prarit Bhargava <[email protected]>
Reviewed-by: David E. Box <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
The Chrome EC's features are returned through an
ec_response_get_features struct, but they are stored in an independent
array. Although the two are effectively the same at present (2 unsigned
32 bit ints), there is the possibility that they could go out of sync.
Avoid this by only using the EC struct to store the features.
Signed-off-by: Prashant Malani <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Benson Leung <[email protected]>
There was in the past a typo in the coordinate readouts property. The
bindings have been updated, the touchscreen driver as well and now
supports both. However, the MFD driver that is in charge of verifying
the validity of the property only checks the bogus one. Add support for
the correctly spelled DT property.
Fixes: c9aeb249bf ("Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding")
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
One way of knowing which hardware we are dealing with is to check the
compatible string. When this must be done at several places, it's best
and certainly more clear to use a helper for that.
Introduce ti_adc_with_touchscreen() to indicate if there is a touchscreen
controller available (meaning it's an am33xx-like ADC). This helper does
not indicate if it is actually used (that is the purpose of the use_tsc
boolean).
Introducing this helper helps making a difference in the code between
what is generic to both types of ADCs and what is specific to the am33xx
hardware before introducing support for the am437x hardware.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Just checking the number of wires will soon not be enough, add a boolean
to indicate the actual use or not of the touchscreen.
Certain checks only make sense when there is a touchscreen wired. Make
these checks explicitly depend on the presence of the touchscreen.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
The error message if we cannot retrieve the clock tells us that the
touchscreen controller clock was unavailable. This is wrong, this is the
"main" clock for the hardware block, it is not specific to the
touchscreen and won't change when we will introduce ADC1/magnetic reader
support so let's correct this comment.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
We need to retrieve the number of wires used by the "secondary" device
(the touchscreen or the magnetic reader). Let's rename tsc_wires to
become tscmag_wires to clarify the fact that this variable can be used
in both situations.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
While the register list (and names) between ADC0 and ADC1 are pretty
close, the bits inside changed a little bit. To avoid any future
confusion, let's add the TSC prefix when some bits are in a register
that is common to both revisions of the ADC, but are specific to the
am33xx hardware.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
This bit is common to all devices (ADC, Touchscreen, Magnetic reader) so
make it clear that it can be used from any location by operating a
mechanical rename:
s/CNTRLREG_TSCSSENB/CNTRLREG_SSENB/
Signed-off-by: Miquel Raynal <[email protected]>
Acked-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Instead of deriving in the probe and in the resume path the value of the
ctrl register, let's do it only once in the probe, save the value of
this register (all but the subsystem enable bit) in the driver's
structure and use it from the resume callback.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
TI AM335X TRM [1] states that most of the configuration should be set in
the control register in the first place, before actually enabling the
hardware with the subsystem enable bit.
So far only half of the configuration was made in the first step (before
enabling the "subsystem"), which does not make really sense. Also, the
probe and the resume patch were acting differently. Let's harmonize all
this by following these steps:
1/ Configure the CLKDIV register
2/ Configure the CTRL register
3/ Configure the idle configuration
4/ Really enable the device by rewriting the CTRL register with the
subsystem enable bit set.
[1] https://www.ti.com/lit/pdf/spruh73
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Keeping the count of tsc_cells and adc_cells is completely redundant, we
can derive this information from other variables. Plus, these variables
are not used anywhere else now. Let's get rid of them.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Use the number of touchscreen wires (tsc_wires) instead of the flag
indicating a touchscreen cell (tsc_cell) to mimic the logic from the
probe.
Besides keeping a certain harmony in the driver, the main benefit is
that we are going to simplify the number of entries in the main MFD
structure and tsc_cell can now be removed more easily.
Signed-off-by: Miquel Raynal <[email protected]>
Acked-by: Jonathan Cameron <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Linus Torvalds