This patch converts all remaining users to use the new block cipher type
where applicable. It also changes all simple cipher operations to use
the new encrypt_one/decrypt_one interface.
Signed-off-by: Herbert Xu <[email protected]>
hostap_cs driver
- added support for Proxim Harmony PCI W-Lan Card (uses pd6729 based
pcmcia2pci bridge)
Signed-off-by: Christian Steineck <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Coverity CID 1160 & 1161
Remove some dead code from bcm43xx_sysfs.c in 2.6.18-rc6
Signed-off-by: Darren Jenkins <[email protected]>
Signed-off-by: Larry Finger <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This patch prints out the ucode debug status to sysfs. So, users can
watch the microcode status of their hardware.
Signed-off-by: Martin Langer <[email protected]>
Signed-off-by: Larry Finger <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This patch prints microcode revision, patchlevel, date and time to
KERN_INFO. Also, version 4.xx microcodes (rev>0x128) will be rejected
by the driver, because they still do not work.
Signed-off-by: Martin Langer <[email protected]>
Acked-by: Michael Buesch <[email protected]>
Signed-off-by: Larry Finger <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This patch removes code that was make obsolete when the wireless
statistics in bcm43xx-softmac were changed, but was overlooked at that
time. The value of bcm->stats.link_quality computed here is never used.
Signed-off-by: Larry Finger <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This patch adds bitrate information to the scan result in the Prism54
driver, like some/most other driver do.
Signed-off-by: Jean Tourrilhes <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Inspired by an e-mail by Stephen Hemminger I decided to remove all
unneeded packed attributes from the code where the member variables are
already aligned. This avoids horrible code being generated on some
architectures.
Signed-off-by: Ulrich Kunitz <[email protected]>
Signed-off-by: Daniel Drake <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Tested by Vincent TOUCHARD
zd1211 chip 0b05:170c v4802 high 00-11-d8 AL2230_RF pa0 g---
Signed-off-by: Daniel Drake <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Tested by Martin Dummer.
zd1211 chip 0b3b:5630 v4330 high 00-01-e3 RF2959_RF pa0 ---
Signed-off-by: Daniel Drake <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This patch fixes an out of sequence step in the bcm43xx_init_board
routine for bcm43xx-softmac.
Signed-off-by: Larry Finger <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This fixes various bugs in the init and shutdown code
that would lead to lockups and crashes.
Signed-Off-By: Larry Finger <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Caused by a documentation issue I mixed up fields of the zd_status
structure. This patch fixes it and improves also the average
computation, which is now using only measurements of packets sent
by the access point.
Signed-off-by: Ulrich Kunitz <[email protected]>
Signed-off-by: Daniel Drake <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Found by inspection. The STRIP driver does neigh_lookup() but never
releases. This driver shouldn't being doing gratuitous arp anyway.
Untested, obviously, because of lack of hardware.
Signed-off-by: Stephen Hemminger <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
This patch sets the floor of wireless level (signal) and noise at
-110 dBm, which makes them be comatible with RCPI, as discussed by
Simon Barber. With this change, bcm43xx-softmac and bcm43xx-d80211
behave the same.
Signed-Off-By: Larry Finger <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
When bcm43xx-softmac is given an ifdown/ifup sequence, the value for
bcm->mac_suspended ends up wrong, which leads to a large number of
assert(bcm->mac_suspended>=0) messages. This one-line patch fixes
this problem.
Signed-off-by: Michael Buesch <[email protected]>
Signed-Off-By: Larry Finger <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This patch enables the ipw2200 driver to support passive scanning as
offered by the wireless extensions. For this, I enhanced the ipw_wx_set_scan
function in such a way that it differentiates between a passive and an
active scan request. Additionally, I added a new function called
ipw_request_passive_scan that is similiar to the ipw_request_scan
function to perform passive scans. Last but not least, I added a field
(in fact it is a work_struct struct) called request_passive_scan to
the ipw_priv struct.
Signed-off-by: Thomas King <[email protected]>
Signed-off-by: Zhu Yi <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Fix by removing dependency between priv->action_sem and rtnl semaphore.
Signed-off-by: Zhu Yi <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
If we don't disable the card in the pci .shutdown method, there might be
pending interrupts still in the interrupt line after a reboot on some
platform. This patch fixes the problem by disable the hardware in the pci
.shutdown method.
Signed-off-by: Zhu Yi <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
When command error log debug is enabled, we write every host command and
parameters into a buffer. But we didn't alloc the parameter buffer for this
case. The patch adds struct cmdlog_host_cmd so that the buffer is allocated
from the stack.
Signed-off-by: Zhu Yi <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
The ipw2200 firmware/ucode only support values from 0 to 254. So mark 255
as invalid.
Signed-off-by: Zhu Yi <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
IEEE80211_RADIOTAP_TSFT is defined as the Value in microseconds of the
MAC's 64-bit 802.11 Time Synchronization Function timer when the first bit
of the MPDU arrived at the MAC. Since ipw2200 hardware doesn't provide this
value, we disable this feature from the radiotap header present flag.
Signed-off-by: Zhu Yi <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This patch traps the case when the essid is being set to its
current value. If the essid is being set again and we are already
associated, chances are some other parameters have also been altered.
I think it is safer to do the re-association for this case.
Signed-off-by: Bill Moss <[email protected]>
Signed-off-by: Zhu Yi <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This patch cleanups the ipw_wx_set_essid code and forces a reassociation
when setting the essid to "any". I have tested this patch with iwconfig. It
makes ipw2200 compliant with all the cases mentioned in the iwconfig man
page. The commands
iwconfig iface essid any
iwconfig iface essid -- any
iwconfig iface essid off
iwconfig iface essid on
all seemed to work correctly. None of this worked before the patch.
Note, this patch treats
iwconfig iface essid
iwconfig iface essid ""
The same. It produces an error message: essid: Unknown host.
Since an essid of "" is not mentioned in the iwconfig man page.
Signed-off-by: Bill Moss <[email protected]>
Signed-off-by: Zhu Yi <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
The SIOCGIWFREQ ioctl fills the request structure's freq field by setting
the exponent to 0 and the mantissa to the current channel number. The
iwconfig tool works around this behaviour by looking up the frequency
from the channel table if a frequency below 1kHz is returned, other tools
(e.g. kwlaninfo) don't. According to the comment in the iwconfig source
the driver is supposed to return the frequency, not the channel number.
Signed-off-by: Ingo van Lil <[email protected]>
Signed-off-by: Zhu Yi <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Moving part of the debugging code from IPW_DEBUG to IPW_LL_DEBUG (low level
debugging) and make IPW_DEBUG be always enabled. IPW_LL_DEBUG still needs
to be enabled by selecting CONFIG_IPW2200_DEBUG. But it is highly
deprecated for normal users since it adds higher debug verbosity in driver
hot paths.
Signed-off-by: Zhu Yi <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
hard_start_xmit should return a NETIF_TX_FOO error code.
Signed-off-by: Michael Buesch <[email protected]>
Signed-Off-By: Larry Finger <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Convert the bitfields in the bcm43xx DMA code to properly
aligned u8 booleans. These flags are accessed in the DMA
hotpath, so it's a good idea to waste a few bytes of memory
for the sake of speed by not requiring masking (and probably
shifting) of the bitfields.
Signed-off-by: Michael Buesch <[email protected]>
Signed-Off-By: Larry Finger <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Don't rely on linux/if_arp.h being included by other headers
Signed-off-by: Pavel Roskin <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
SPARC architecture has been fixed, so it's no longer needed.
Signed-off-by: Pavel Roskin <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Calls to bcm43xx_rng_init() and bcm43xx_rng_exit() got
lost due to merge trouble. Re-add them.
Signed-off-by: Michael Buesch <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This is a rewrite of the bcm43xx DMA engine. It adds support
for >1G of memory (for chips that support the extension bits)
and 64-bit DMA (for chips that support it).
Signed-off-by: Michael Buesch <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
The airo driver is currently caching a pid for later use, but with the
implementation of containers, pids themselves do not uniquely identify a
task. The driver is also using kernel_thread() which is deprecated in
drivers.
This patch essentially replaces the kernel_thread() with kthread_create().
It also stores the task_struct of the airo_thread rather than its pid.
Since this introduces a second task_struct in struct airo_info, the patch
renames airo_info.task to airo_info.list_bss_task.
As an extension of these changes, the patch further:
- replaces kill_proc() with kthread_stop()
- replaces signal_pending() with kthread_should_stop()
- removes thread completion synchronisation which is handled by
kthread_stop().
[[email protected]: fix races]
Signed-off-by: Sukadev Bhattiprolu <[email protected]>
Cc: Javier Achirica <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Intersil firmware 1.7.4 (and possibly others) loses the antenna
selection settings when the port is reset.
Signed-off-by: David Acker <[email protected]>
Signed-off-by: Pavel Roskin <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
This bug was introduced during the PCMCIA API conversion and broke
spectrum_cs completely.
Tracked down by Fredrik Tolf <[email protected]>
Signed-off-by: Pavel Roskin <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
Jeff Garzik